linux-4.19.x.patch

diff --git a/arch/arm/boot/dts/acme-acqua.dts b/arch/arm/boot/dts/acme-acqua.dts
new file mode 100644
index 000000000..264af2980
--- /dev/null
+++ b/arch/arm/boot/dts/acme-acqua.dts
@@ -0,0 +1,301 @@
+/*
+ * acme-acqua.dts - Device Tree file for Acqua A5 Board
+ *
+ *  Copyright (C) 2014 Atmel,
+ *		  2014 Nicolas Ferre <nicolas.ferre@atmel.com>
+ * 
+ *	2020 Sergio Tanzilli <tanzilli@acmesystems.it>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "sama5d31.dtsi"
+
+/ {
+	model = "Acme Systems Acqua SOM";
+	compatible = "acme,acqua", "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		bootargs = "mem=256M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait consoleblank=0";
+	};
+
+	memory {
+		reg = <0x20000000 0x10000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			hlcdc: hlcdc@f0030000 {
+				status = "disabled";
+				hlcdc-display-controller {
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888_alt>;
+					port@0 {
+						hlcdc_panel_output: endpoint@0 {
+							remote-endpoint = <&panel_input>;
+						};
+					};
+				};
+			};
+		
+			/* MicroSD mounted on the SOM */
+		
+			mmc0: mmc@f0000000 {
+				pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+				};
+			};
+  
+  			/* Optional MicroSD to mount on the carrier board */
+  
+			mmc1: mmc@f8000000 {
+				pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+				status = "disabled";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioE 1 GPIO_ACTIVE_LOW>;
+				};
+			};
+
+			spi0: spi@f0004000 {
+				cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
+				status = "disabled";
+			};
+
+			can0: can@f000c000 {
+				status = "disabled";
+			};
+
+			tcb0: timer@f0010000 {
+				timer0: timer@0 {
+					compatible = "atmel,tcb-timer";
+					reg = <0>;
+				};
+
+				timer1: timer@1 {
+					compatible = "atmel,tcb-timer";
+					reg = <1>;
+				};
+			};
+
+			i2c0: i2c@f0014000 {
+				pinctrl-0 = <&pinctrl_i2c0_pu>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@f0018000 {
+				status = "disabled";
+			};
+
+			macb1: ethernet@f802c000 {
+				compatible = "atmel,sama5d3-macb", "cdns,at91sam9260-macb", "cdns,macb";
+				
+				status = "okay";
+				phy-mode = "rmii";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				nvmem-cells = <&eth0_addr>;
+				nvmem-cell-names = "mac-address";
+
+                phy0: ethernet-phy@1 {
+                    interrupt-parent = <&pioE>;
+                    interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
+                    reg = <1>;
+                };
+
+				/*ethernet-phy@1 {
+					reg = <0x1>;
+				};*/
+			};
+
+			/* Bit banging internal I2C to manage the AT24MAC402 chip */
+
+			i2c3@ {
+				compatible = "i2c-gpio";
+				gpios = <&pioE 1 0 /* SDA */
+						 &pioE 2 0 /* SCK */
+						>;
+				i2c-gpio,delay-us = <4>;    /* ~178 kHz */
+				#address-cells = <1>;
+				#size-cells = <0>;
+			
+				/* EEPROM contains the eth0 MAC address */
+				 
+				eeprom@58 {
+					compatible = "atmel,24mac402";
+					pagesize = <256>;
+					read-only;
+					reg = <0x58>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					eth0_addr: eth-mac-addr@9A {
+						reg = <0x0 0x06>;
+					};
+				};
+			};
+
+			pwm0: pwm@f002c000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_pwm0_pwmh0_0 &pinctrl_pwm0_pwmh1_0>;
+				status = "disabled";
+			};
+
+			usart0: serial@f001c000 {
+				status = "okay";
+			};
+
+			usart1: serial@f0020000 {
+				pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
+				status = "disabled";
+			};
+
+			uart0: serial@f0024000 {
+				status = "disabled";
+			};
+
+
+			spi1: spi@f8008000 {
+				cs-gpios = <&pioC 25 0>;
+				status = "disabled";
+			};
+
+			adc0: adc@f8018000 {
+				atmel,adc-vref = <3300>;
+				atmel,adc-channels-used = <0xfe>;
+				pinctrl-0 = <
+					&pinctrl_adc0_adtrg
+					&pinctrl_adc0_ad1
+					&pinctrl_adc0_ad2
+					&pinctrl_adc0_ad3
+					&pinctrl_adc0_ad4
+					&pinctrl_adc0_ad5
+					&pinctrl_adc0_ad6
+					&pinctrl_adc0_ad7
+					>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@f801c000 {
+				dmas = <0>, <0>;	/* Do not use DMA for i2c2 */
+				pinctrl-0 = <&pinctrl_i2c2_pu>;
+				status = "disabled";
+			};
+
+
+			dbgu: serial@ffffee00 {
+				status = "okay";
+			};
+
+			pinctrl@fffff200 {
+				board {
+					pinctrl_i2c0_pu: i2c0_pu {
+						atmel,pins =
+							<AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+							<AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+					};
+
+					pinctrl_i2c2_pu: i2c2_pu {
+						atmel,pins =
+							<AT91_PIOA 18 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>,
+							<AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
+					};
+
+					pinctrl_key_gpio: key_gpio_0 {
+						atmel,pins =
+							<AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+					};
+
+					pinctrl_mmc0_cd: mmc0_cd {
+						atmel,pins =
+							<AT91_PIOE 0 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+					};
+
+					pinctrl_mmc1_cd: mmc1_cd {
+						atmel,pins =
+							<AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+					};
+
+					pinctrl_usba_vbus: usba_vbus {
+						atmel,pins =
+							<AT91_PIOE 9 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;	/* PE9, conflicts with A9 */
+					};
+				};
+			};
+		};
+
+        usb0: gadget@500000 {
+            status = "okay";
+        };
+
+        usb1: ohci@600000 {
+            status = "okay";
+        };
+
+        usb2: ehci@700000 {
+            status = "okay";
+        };
+		
+	};
+
+
+	panel: panel {
+		/* compatible = "acme,43inch", "simple-panel"; */
+		compatible = "acme,50inch", "simple-panel";
+		/* compatible = "acme,70inch", "simple-panel"; */
+		
+		status = "disable";
+
+		port@0 {
+			panel_input: endpoint@0 {
+				remote-endpoint = <&hlcdc_panel_output>;
+			};
+		};
+	};
+
+ 
+	leds {
+		compatible = "gpio-leds";
+
+		led0 {
+			label = "led0";
+			gpios = <&pioE 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led1 {
+			label = "led1";
+			gpios = <&pioE 4 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led2 {
+			label = "led2";
+			gpios = <&pioE 5 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led3 {
+			label = "led3";
+			gpios = <&pioE 6 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+	};		
+};
diff --git a/arch/arm/boot/dts/acme-aria.dts b/arch/arm/boot/dts/acme-aria.dts
new file mode 100644
index 000000000..f0e8f1b87
--- /dev/null
+++ b/arch/arm/boot/dts/acme-aria.dts
@@ -0,0 +1,137 @@
+/*
+ * at91-ariag25.dts - Device Tree file for Acme Systems Aria G25 (AT91SAM9G25 based)
+ *
+ * Copyright (C) 2013 Douglas Gilbert <dgilbert@interlog.com>,
+ *                    Robert Nelson <robertcnelson@gmail.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "at91sam9g25.dtsi"
+
+/ {
+	model = "Acme Systems Aria G25";
+	compatible = "acme,ariag25", "atmel,at91sam9x5", "atmel,at91sam9";
+
+	aliases {
+		serial0 = &dbgu;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		/* 128 MB, change this for 256 MB revision */
+		reg = <0x20000000 0x8000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			mmc0: mmc@f0008000 {
+				pinctrl-0 = <
+					&pinctrl_mmc0_slot0_clk_cmd_dat0
+					&pinctrl_mmc0_slot0_dat1_3>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+				};
+			};
+
+			tcb0: timer@f8008000 {
+				timer@0 {
+					compatible = "atmel,tcb-timer";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-timer";
+					reg = <1>;
+				};
+			};
+
+			macb0: ethernet@f802c000 {
+				phy-mode = "rmii";
+				/*
+				 * following can be overwritten by bootloader:
+				 * for example u-boot 'ftd set' command
+				 */
+				local-mac-address = [00 00 00 00 00 00];
+				status = "okay";
+			};
+
+			/*
+			 * UART0/1 pins are marked as GPIO on
+			 * Aria documentation.
+			 * Change to "okay" if you need additional serial ports
+			 */
+			uart0: serial@f8040000 {
+				status = "disabled";
+			};
+
+			uart1: serial@f8044000 {
+				status = "disabled";
+			};
+
+			adc0: adc@f804c000 {
+				status = "okay";
+				atmel,adc-channels-used = <0xf>;
+			};
+
+			dbgu: serial@fffff200 {
+				status = "okay";
+			};
+
+			pinctrl@fffff400 {
+				w1_0 {
+					pinctrl_w1_0: w1_0-0 {
+						atmel,pins = <0 21 0x0 0x1>; /* PA21 PIO, pull-up */
+					};
+				};
+			};
+
+			rtc@fffffeb0 {
+				status = "okay";
+			};
+		};
+
+		usb0: ohci@600000 {
+			status = "okay";
+			num-ports = <3>;
+		};
+
+		usb1: ehci@700000 {
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* little green LED in middle of Aria G25 module */
+		aria_led {
+			label = "aria_led";
+			gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
+			linux,default-trigger = "heartbeat";
+		};
+
+	};
+
+	onewire {
+		compatible = "w1-gpio";
+		gpios = <&pioA 21 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_w1_0>;
+	};
+};
diff --git a/arch/arm/boot/dts/acme-arietta-alessia.dts b/arch/arm/boot/dts/acme-arietta-alessia.dts
new file mode 100644
index 000000000..d6eb596cf
--- /dev/null
+++ b/arch/arm/boot/dts/acme-arietta-alessia.dts
@@ -0,0 +1,92 @@
+/*
+ * Device Tree file for Arietta G25
+ * https://www.acmesystems.it/arietta
+ */
+ 
+/dts-v1/;
+#include "at91sam9g25.dtsi"
+/ {
+	model = "Acme Systems Arietta G25";
+	compatible = "acme,ariettag25", "atmel,at91sam9x5", "atmel,at91sam9";
+
+	aliases {
+		serial0 = &dbgu;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		bootargs = "mem=256M  console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait";
+	};
+
+	memory {
+		reg = <0x20000000 0x8000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			mmc0: mmc@f0008000 {
+				pinctrl-0 = <
+				  &pinctrl_mmc0_slot0_clk_cmd_dat0
+				  &pinctrl_mmc0_slot0_dat1_3>;
+				status = "okay";
+
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+				};
+			};
+
+			tcb0: timer@f8008000 {
+				timer@0 {
+					compatible = "atmel,tcb-timer";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-timer";
+					reg = <1>;
+				};
+			};
+
+			usb2: gadget@f803c000 {
+				status = "okay";
+			};
+
+			dbgu: serial@fffff200 {
+				status = "okay";
+			};
+
+			rtc@fffffeb0 {
+				status = "okay";
+			};
+		};
+
+		usb0: ohci@600000 {
+			status = "okay";
+			num-ports = <3>;
+		};
+
+		usb1: ehci@700000 {
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		arietta_led {
+			label = "arietta_led";
+			gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/acme-arietta.dts b/arch/arm/boot/dts/acme-arietta.dts
new file mode 100644
index 000000000..d6eb596cf
--- /dev/null
+++ b/arch/arm/boot/dts/acme-arietta.dts
@@ -0,0 +1,92 @@
+/*
+ * Device Tree file for Arietta G25
+ * https://www.acmesystems.it/arietta
+ */
+ 
+/dts-v1/;
+#include "at91sam9g25.dtsi"
+/ {
+	model = "Acme Systems Arietta G25";
+	compatible = "acme,ariettag25", "atmel,at91sam9x5", "atmel,at91sam9";
+
+	aliases {
+		serial0 = &dbgu;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		bootargs = "mem=256M  console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait";
+	};
+
+	memory {
+		reg = <0x20000000 0x8000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			mmc0: mmc@f0008000 {
+				pinctrl-0 = <
+				  &pinctrl_mmc0_slot0_clk_cmd_dat0
+				  &pinctrl_mmc0_slot0_dat1_3>;
+				status = "okay";
+
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+				};
+			};
+
+			tcb0: timer@f8008000 {
+				timer@0 {
+					compatible = "atmel,tcb-timer";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-timer";
+					reg = <1>;
+				};
+			};
+
+			usb2: gadget@f803c000 {
+				status = "okay";
+			};
+
+			dbgu: serial@fffff200 {
+				status = "okay";
+			};
+
+			rtc@fffffeb0 {
+				status = "okay";
+			};
+		};
+
+		usb0: ohci@600000 {
+			status = "okay";
+			num-ports = <3>;
+		};
+
+		usb1: ehci@700000 {
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		arietta_led {
+			label = "arietta_led";
+			gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/acme-roadrunner-10uart.dts b/arch/arm/boot/dts/acme-roadrunner-10uart.dts
new file mode 100644
index 000000000..10754e301
--- /dev/null
+++ b/arch/arm/boot/dts/acme-roadrunner-10uart.dts
@@ -0,0 +1,393 @@
+/*
+ * acme_roadrunner.dts - Device Tree file for Acme Systems
+ * RoadRunner SOM 
+ *
+ */
+
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/gpio/gpio.h>
+
+
+/ {
+	model = "Acme Systems SAMA5D2 Roadrunner";
+	compatible = "atmel,sama5d2-roadrunner", "atmel,sama5d27","atmel,sama5d2", "atmel,sama5";
+
+	bootargs = "mem=256M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait consoleblank=0";
+
+	aliases {
+		serial0 = &uart1; /* /dev/ttyS0 Debug port */
+		serial1 = &uart2; /* /dev/ttyS1            */
+		serial2 = &uart3; /* /dev/ttyS2            */
+		serial3 = &uart4; /* /dev/ttyS3            */
+		serial4 = &uart0; /* /dev/ttyS4            */
+		serial5 = &uart5; /* /dev/ttyS5            */
+		serial6 = &uart6; /* /dev/ttyS6            */
+		serial7 = &uart7; /* /dev/ttyS7            */
+		serial8 = &uart8; /* /dev/ttyS8            */
+		serial9 = &uart9; /* /dev/ttyS9            */
+	};
+
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		usb0: gadget@300000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+
+		usb1: ohci@400000 {
+			num-ports = <3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb_default>;
+			status = "okay";
+		};
+
+		usb2: ehci@500000 {
+			status = "okay";
+		};
+
+		sdmmc1: sdio-host@b0000000 {
+			bus-width = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc1_default>;
+			non-removable;
+			status = "okay"; /* conflict with qspi0 */
+		};
+
+		apb {
+			macb0: ethernet@f8008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+				phy-mode = "rmii";
+				status = "okay";
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+					interrupt-parent = <&pioA>;
+					interrupts = <73 IRQ_TYPE_LEVEL_LOW>;
+				};
+			};
+
+			tcb0: timer@f800c000 {
+				timer0: timer@0 {
+					compatible = "atmel,tcb-timer";
+					reg = <0>;
+				};
+
+				timer1: timer@1 {
+					compatible = "atmel,tcb-timer";
+					reg = <1>;
+				};
+			};
+
+
+			/* /dev/ttyS0 */
+			/* Debug port */
+
+			uart1: serial@f8020000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_ioset1>;
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				status = "okay";
+			};
+
+			/* /dev/ttyS1 */
+
+			uart2: serial@f8024000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart2_ioset1>;
+				status = "okay";
+			};
+
+			/* /dev/ttyS2 */
+
+			uart3: serial@fc008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart3_ioset1>;
+				status = "okay";
+			};
+
+			/* /dev/ttyS3 */
+
+			uart4: serial@fc00c000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart4_ioset1>;
+				status = "okay";
+			};
+
+			/* /dev/ttyS4 */
+
+			uart0: serial@f801c000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart0_ioset1>;
+				status = "okay";
+			};
+
+
+			/* /dev/ttyS5 */
+
+			flx0: flexcom@f8034000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+				status = "okay"; 
+
+				uart5: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&flx0_clk>;
+					clock-names = "usart";
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx0_ioset1>;
+					atmel,fifo-size = <32>;
+					status = "okay";
+				};
+			};
+
+			/* /dev/ttyS6 */
+
+			flx1: flexcom@f8038000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+				status = "okay"; 
+
+				uart6: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&flx1_clk>;
+					clock-names = "usart";
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx1_ioset1>;
+					atmel,fifo-size = <32>;
+					status = "okay";
+				};
+			};
+
+			/* /dev/ttyS7 */
+
+			flx2: flexcom@fc010000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+				status = "okay";
+
+				uart7: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <21 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&flx2_clk>;
+					clock-names = "usart";
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx2_ioset1>;
+					atmel,fifo-size = <32>;
+					status = "okay";
+				};
+			};
+
+
+			/* /dev/ttyS8 */
+
+			flx3: flexcom@fc014000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+				status = "okay";
+
+				uart8: serial@200 {
+					dmas = <0>, <0>;
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&flx3_clk>;
+					clock-names = "usart";
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx3_ioset1>;
+					atmel,fifo-size = <32>; 
+					status = "okay"; 
+				};
+			};
+
+
+			/* /dev/ttyS9 */
+
+			flx4: flexcom@fc018000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+				status = "okay";
+
+				uart9: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&flx4_clk>;
+					clock-names = "usart";
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx4_ioset1>;
+					atmel,fifo-size = <32>;
+					status = "okay"; 
+				};
+			};
+
+			shdwc@f8048010 {
+				atmel,shdwc-debouncer = <976>;
+				atmel,wakeup-rtc-timer;
+
+				input@0 {
+					reg = <0>;
+					atmel,wakeup-type = "low";
+				};
+			};
+
+			watchdog@f8048040 {
+				status = "okay";
+			};
+
+			pinctrl@fc038000 {
+
+				pinctrl_uart0_ioset1: uart0_ioset1 {
+					pinmux = <PIN_PB26__URXD0>,
+						 <PIN_PB27__UTXD0>;
+					bias-disable;
+				};
+
+				/* Debug port */
+
+				pinctrl_uart1_ioset1: uart1_ioset1 {
+					pinmux = <PIN_PD2__URXD1>,
+						 <PIN_PD3__UTXD1>;
+					bias-disable;
+				};
+
+				pinctrl_uart2_ioset1: uart2_ioset1 {
+					pinmux = <PIN_PD4__URXD2>,
+						 <PIN_PD5__UTXD2>;
+					bias-disable;
+				};
+
+				pinctrl_uart2_ioset2: uart2_ioset2 {
+					pinmux = <PIN_PD23__URXD2>,
+						 <PIN_PD24__UTXD2>;
+					bias-disable;
+				};
+
+				pinctrl_uart2_ioset3: uart2_ioset3 {
+					pinmux = <PIN_PD19__URXD2>,
+						 <PIN_PD20__UTXD2>;
+					bias-disable;
+				};
+
+				pinctrl_uart3_ioset1: uart3_ioset1 {
+					pinmux = <PIN_PC12__URXD3>,
+						 <PIN_PC13__UTXD3>;
+					bias-disable;
+				};
+
+				pinctrl_uart3_ioset2: uart3_ioset2 {
+					pinmux = <PIN_PC31__URXD3>,
+						 <PIN_PD0__UTXD3>;
+					bias-disable;
+				};
+
+				pinctrl_uart3_ioset3: uart3_ioset3 {
+					pinmux = <PIN_PB11__URXD3>,
+						 <PIN_PB12__UTXD3>;
+					bias-disable;
+				};
+
+				pinctrl_uart4_ioset1: uart4_ioset1 {
+					pinmux = <PIN_PB3__URXD4>,
+						 <PIN_PB4__UTXD4>;
+					bias-disable;
+				};
+
+				pinctrl_flx0_ioset1: flx0_ioset1 {
+					pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+						 <PIN_PB29__FLEXCOM0_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_flx1_ioset1: flx1_ioset1 {
+					pinmux = <PIN_PA24__FLEXCOM1_IO0>,
+						 <PIN_PA23__FLEXCOM1_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_flx2_ioset1: flx2_ioset1 {
+					pinmux = <PIN_PD26__FLEXCOM2_IO0>,
+						 <PIN_PD27__FLEXCOM2_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_flx3_ioset1: flx3_ioset1 {
+					pinmux = <PIN_PA15__FLEXCOM3_IO0>,
+						 <PIN_PA13__FLEXCOM3_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_flx4_ioset1: flx4_ioset1 {
+					pinmux = <PIN_PC28__FLEXCOM4_IO0>,
+						 <PIN_PC29__FLEXCOM4_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_macb0_default: macb0_default {
+					pinmux = <PIN_PB14__GTXCK>,
+						 <PIN_PB15__GTXEN>,
+						 <PIN_PB16__GRXDV>,
+						 <PIN_PB17__GRXER>,
+						 <PIN_PB18__GRX0>,
+						 <PIN_PB19__GRX1>,
+						 <PIN_PB20__GTX0>,
+						 <PIN_PB21__GTX1>,
+						 <PIN_PB22__GMDC>,
+						 <PIN_PB23__GMDIO>;
+					bias-disable;
+				};
+
+				pinctrl_macb0_phy_irq: macb0_phy_irq {
+					pinmux = <PIN_PC9__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_sdmmc1_default: sdmmc1_default {
+					cmd_data {
+						pinmux = <PIN_PA28__SDMMC1_CMD>,
+							 <PIN_PA18__SDMMC1_DAT0>,
+							 <PIN_PA19__SDMMC1_DAT1>,
+							 <PIN_PA20__SDMMC1_DAT2>,
+							 <PIN_PA21__SDMMC1_DAT3>;
+						bias-pull-up;
+					};
+
+					conf-ck_cd {
+						pinmux = <PIN_PA22__SDMMC1_CK>;
+						bias-disable;
+					};
+				};
+
+
+				pinctrl_usb_default: usb_default {
+					pinmux = <PIN_PB10__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_usba_vbus: usba_vbus {
+					pinmux = <PIN_PA31__GPIO>;
+					bias-disable;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/acme-roadrunner-banco.dts b/arch/arm/boot/dts/acme-roadrunner-banco.dts
new file mode 100644
index 000000000..afc83deeb
--- /dev/null
+++ b/arch/arm/boot/dts/acme-roadrunner-banco.dts
@@ -0,0 +1,404 @@
+/*
+ * acme-roadrunner-banco.dts - Device Tree file for Acme Systems
+ * RoadRunner Bench Test
+ *
+ *  Copyright (C) 2015 Atmel,
+ *                2015 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *                2020 Sergio Tanzilli <tanzilli@acmesystems.it>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/gpio/gpio.h>
+
+
+
+/ {
+	model = "Acme Systems SAMA5D2 Roadrunner";
+	compatible = "atmel,sama5d2-roadrunner", "atmel,sama5d27","atmel,sama5d2", "atmel,sama5";
+
+	bootargs = "mem=256M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait consoleblank=0";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		usb0: gadget@300000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+
+		usb1: ohci@400000 {
+			num-ports = <3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb_default>;
+			status = "okay";
+		};
+
+		usb2: ehci@500000 {
+			status = "okay";
+		};
+
+		sdmmc1: sdio-host@b0000000 {
+			bus-width = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc1_default>;
+			non-removable;
+			status = "okay"; /* conflict with qspi0 */
+		};
+
+		apb {
+
+			macb0: ethernet@f8008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+				phy-mode = "rmii";
+				status = "okay";
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+					interrupt-parent = <&pioA>;
+					interrupts = <73 IRQ_TYPE_LEVEL_LOW>;
+					/*interrupts = <PIN_PC9 IRQ_TYPE_LEVEL_LOW>;*/
+				};
+			};
+
+			tcb0: timer@f800c000 {
+				timer0: timer@0 {
+					compatible = "atmel,tcb-timer";
+					reg = <0>;
+				};
+
+				timer1: timer@1 {
+					compatible = "atmel,tcb-timer";
+					reg = <1>;
+				};
+			};
+
+			uart1: serial@f8020000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_default>;
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				status = "okay";
+			};
+
+			shdwc@f8048010 {
+				atmel,shdwc-debouncer = <976>;
+				atmel,wakeup-rtc-timer;
+
+				input@0 {
+					reg = <0>;
+					atmel,wakeup-type = "low";
+				};
+			};
+
+			watchdog@f8048040 {
+				status = "okay";
+			};
+
+			vddin_3v3: fixed-regulator-vddin_3v3 {
+				compatible = "regulator-fixed";
+
+				regulator-name = "VDDIN_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				status = "okay";
+			};
+
+			vddana: fixed-regulator-vddana {
+				compatible = "regulator-fixed";
+
+				regulator-name = "VDDANA";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				vin-supply = <&vddin_3v3>;
+				status = "okay";
+			};
+
+			advref: fixed-regulator-advref {
+				compatible = "regulator-fixed";
+
+				regulator-name = "advref";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				vin-supply = <&vddana>;
+				status = "okay";
+			};
+
+			adc: adc@fc030000 {
+				vddana-supply = <&vddana>; 
+				vref-supply =  <&vddana>; 
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_adc_default>;
+				status = "okay";
+			};
+
+			pinctrl@fc038000 {
+				/*
+				 * There is no real pinmux for ADC, if the pin
+				 * is not requested by another peripheral then
+				 * the muxing is done when channel is enabled.
+				 * Requesting pins for ADC is GPIO is
+				 * encouraged to prevent conflicts and to
+				 * disable bias in order to be in the same
+				 * state when the pin is not muxed to the adc.
+				 */
+				pinctrl_adc_default: adc_default {
+					pinmux = <PIN_PD29__GPIO>,
+						<PIN_PD30__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_can0_default: can0_default {
+					pinmux = <PIN_PC10__CANTX0>,
+						 <PIN_PC11__CANRX0>;
+					bias-disable;
+				};
+
+				pinctrl_can1_default: can1_default {
+					pinmux = <PIN_PC26__CANTX1>,
+						 <PIN_PC27__CANRX1>;
+					bias-disable;
+				};
+
+				/*
+				 * The ADTRG pin can work on any edge type.
+				 * In here it's being pulled up, so need to
+				 * connect it to ground to get an edge e.g.
+				 * Trigger can be configured on falling, rise
+				 * or any edge, and the pull-up can be changed
+				 * to pull-down or left floating according to
+				 * needs.
+				 */
+				pinctrl_adtrg_default: adtrg_default {
+					pinmux = <PIN_PD31__ADTRG>;
+					bias-pull-up;
+				};
+
+				pinctrl_charger_chglev: charger_chglev {
+					pinmux = <PIN_PA12__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_charger_irq: charger_irq {
+					pinmux = <PIN_PB13__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_charger_lbo: charger_lbo {
+					pinmux = <PIN_PC8__GPIO>;
+					bias-pull-up;
+				};
+
+				pinctrl_classd_default: classd_default {
+					pinmux = <PIN_PB1__CLASSD_R0>,
+						 <PIN_PB2__CLASSD_R1>,
+						 <PIN_PB3__CLASSD_R2>,
+						 <PIN_PB4__CLASSD_R3>;
+					bias-pull-up;
+				};
+
+				pinctrl_flx0_default: flx0_default {
+					pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+						 <PIN_PB29__FLEXCOM0_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_flx4_default: flx4_default {
+					pinmux = <PIN_PD12__FLEXCOM4_IO0>,
+						 <PIN_PD13__FLEXCOM4_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_i2c0_default: i2c0_default {
+					pinmux = <PIN_PD21__TWD0>,
+						 <PIN_PD22__TWCK0>;
+					bias-disable;
+				};
+
+				pinctrl_i2c1_default: i2c1_default {
+					pinmux = <PIN_PD4__TWD1>,
+						 <PIN_PD5__TWCK1>;
+					bias-disable;
+				};
+
+				pinctrl_key_gpio_default: key_gpio_default {
+					pinmux = <PIN_PB9__GPIO>;
+					bias-pull-up;
+				};
+
+				pinctrl_macb0_default: macb0_default {
+					pinmux = <PIN_PB14__GTXCK>,
+						 <PIN_PB15__GTXEN>,
+						 <PIN_PB16__GRXDV>,
+						 <PIN_PB17__GRXER>,
+						 <PIN_PB18__GRX0>,
+						 <PIN_PB19__GRX1>,
+						 <PIN_PB20__GTX0>,
+						 <PIN_PB21__GTX1>,
+						 <PIN_PB22__GMDC>,
+						 <PIN_PB23__GMDIO>;
+					bias-disable;
+				};
+
+				pinctrl_macb0_phy_irq: macb0_phy_irq {
+					pinmux = <PIN_PC9__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_pdmic_default: pdmic_default {
+					pinmux = <PIN_PB26__PDMIC_DAT>,
+						<PIN_PB27__PDMIC_CLK>;
+					bias-disable;
+				};
+
+				pinctrl_sdmmc0_default: sdmmc0_default {
+					cmd_data {
+						pinmux = <PIN_PA1__SDMMC0_CMD>,
+							 <PIN_PA2__SDMMC0_DAT0>,
+							 <PIN_PA3__SDMMC0_DAT1>,
+							 <PIN_PA4__SDMMC0_DAT2>,
+							 <PIN_PA5__SDMMC0_DAT3>,
+							 <PIN_PA6__SDMMC0_DAT4>,
+							 <PIN_PA7__SDMMC0_DAT5>,
+							 <PIN_PA8__SDMMC0_DAT6>,
+							 <PIN_PA9__SDMMC0_DAT7>;
+						bias-disable;
+					};
+
+					ck_cd_rstn_vddsel {
+						pinmux = <PIN_PA0__SDMMC0_CK>,
+							 <PIN_PA10__SDMMC0_RSTN>,
+							 <PIN_PA11__SDMMC0_VDDSEL>,
+							 <PIN_PA13__SDMMC0_CD>;
+						bias-disable;
+					};
+				};
+
+				pinctrl_sdmmc1_default: sdmmc1_default {
+					cmd_data {
+						pinmux = <PIN_PA28__SDMMC1_CMD>,
+							 <PIN_PA18__SDMMC1_DAT0>,
+							 <PIN_PA19__SDMMC1_DAT1>,
+							 <PIN_PA20__SDMMC1_DAT2>,
+							 <PIN_PA21__SDMMC1_DAT3>;
+						bias-pull-up;
+					};
+
+					conf-ck_cd {
+						pinmux = <PIN_PA22__SDMMC1_CK>;
+						bias-disable;
+					};
+				};
+
+				pinctrl_spi0_default: spi0_default {
+					pinmux = <PIN_PA14__SPI0_SPCK>,
+						 <PIN_PA15__SPI0_MOSI>,
+						 <PIN_PA16__SPI0_MISO>,
+						 <PIN_PA17__SPI0_NPCS0>;
+					bias-disable;
+				};
+
+				pinctrl_uart1_default: uart1_default {
+					pinmux = <PIN_PD2__URXD1>,
+						 <PIN_PD3__UTXD1>;
+					bias-disable;
+				};
+
+				pinctrl_uart3_default: uart3_default {
+					pinmux = <PIN_PB11__URXD3>,
+						 <PIN_PB12__UTXD3>;
+					bias-disable;
+				};
+
+				pinctrl_usb_default: usb_default {
+					pinmux = <PIN_PB10__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_usba_vbus: usba_vbus {
+					pinmux = <PIN_PA31__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_pwm0_pwm2_default: pwm0_pwm2_default {
+					pinmux = <PIN_PB5__PWMH2>,
+						 <PIN_PB6__PWML2>;
+					bias-pull-up;
+				};
+			};
+
+			classd: classd@fc048000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_classd_default>;
+				atmel,pwm-type = "diff";
+				atmel,non-overlap-time = <10>;
+				status = "disabled";
+			};
+
+			can1: can@fc050000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_can1_default>;
+				status = "disabled";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/acme-roadrunner-display.dts b/arch/arm/boot/dts/acme-roadrunner-display.dts
new file mode 100644
index 000000000..e1c4fdb2c
--- /dev/null
+++ b/arch/arm/boot/dts/acme-roadrunner-display.dts
@@ -0,0 +1,452 @@
+/*
+ * Device Tree file for Acme Systems for RoadRunner SOM 
+ * 7 inch TFT 
+ * https://github.com/linux4sam/dt-overlay-at91/blob/master/sama5d2_ptc_ek/sama5d2_ptc_ek_pda5.dtso
+ * https://www.linux4sam.org/bin/view/Linux4SAM/UsingAtmelDRMDriver
+ *
+ *  Copyright (C) 2015 Atmel,
+ *                2015 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *                2020 Sergio Tanzilli <tanzilli@acmesystems.it>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Acme Systems SAMA5D2 Roadrunner";
+	compatible = "atmel,sama5d2-roadrunner", "atmel,sama5d27","atmel,sama5d2", "atmel,sama5";
+
+	bootargs = "mem=256M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait consoleblank=0";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+
+		usb0: gadget@300000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+
+		usb1: ohci@400000 {
+			num-ports = <3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb_default>;
+			status = "okay";
+		};
+
+		usb2: ehci@500000 {
+			status = "okay";
+		};
+
+		sdmmc1: sdio-host@b0000000 {
+			bus-width = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc1_default>;
+			non-removable;
+			status = "okay"; /* conflict with qspi0 */
+		};
+
+		apb {
+			hlcdc: hlcdc@f0000000 {
+				status = "okay";
+
+				hlcdc-display-controller {
+
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb666>;
+
+					port@0 {
+						#address-cells = <1>;
+						#size-cells = <0>;
+						hlcdc_panel_output: endpoint@0 {
+							reg = <0>;
+							remote-endpoint = <&panel_input>;
+						};
+					};
+				};
+				
+				hlcdc_pwm: hlcdc-pwm {
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_lcd_pwm>;
+				};
+				
+			};	
+
+			backlight: backlight {
+				compatible = "pwm-backlight";
+				pwms = <&hlcdc_pwm 0 50000 0>;
+				brightness-levels = <0 4 8 16 32 64 128 255>;
+				default-brightness-level = <7>;
+				power-supply = <&bl_reg>;
+				status = "okay";
+			};
+
+			bl_reg: backlight_regulator {
+				compatible = "regulator-fixed";
+				regulator-name = "backlight-power-supply";
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+				status = "okay";
+			};
+
+			panel: panel {
+				/* compatible = "pda,91-00156-a0", "simple-panel"; */
+				compatible = "innolux,g070y2-l01", "simple-panel";
+				backlight = <&backlight>;
+				power-supply = <&panel_reg>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "okay";
+
+				port@0 {
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					panel_input: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&hlcdc_panel_output>;
+					};
+				};
+			};
+
+			panel_reg: panel_regulator {
+				compatible = "regulator-fixed";
+				regulator-name = "panel-power-supply";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				status = "okay";
+			};
+
+
+			macb0: ethernet@f8008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+				phy-mode = "rmii";
+				status = "okay";
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+					interrupt-parent = <&pioA>;
+					interrupts = <73 IRQ_TYPE_LEVEL_LOW>;
+					/*interrupts = <PIN_PC9 IRQ_TYPE_LEVEL_LOW>;*/
+				};
+			};
+
+			tcb0: timer@f800c000 {
+				timer0: timer@0 {
+					compatible = "atmel,tcb-timer";
+					reg = <0>;
+				};
+
+				timer1: timer@1 {
+					compatible = "atmel,tcb-timer";
+					reg = <1>;
+				};
+			};
+
+			uart1: serial@f8020000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_default>;
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				status = "okay";
+			};
+
+			shdwc@f8048010 {
+				atmel,shdwc-debouncer = <976>;
+				atmel,wakeup-rtc-timer;
+
+				input@0 {
+					reg = <0>;
+					atmel,wakeup-type = "low";
+				};
+			};
+
+			watchdog@f8048040 {
+				status = "okay";
+			};
+
+			pinctrl@fc038000 {
+			
+				pinctrl_lcd_base: pinctrl_lcd_base {
+					pinmux = <PIN_PC30__LCDVSYNC>,
+						 <PIN_PC31__LCDHSYNC>,
+						 <PIN_PD1__LCDDEN>,
+						 <PIN_PD0__LCDPCK>;
+					bias-disable;
+					/* atmel,drive-strength = <ATMEL_PIO_DRVSTR_ME>; */
+				};
+
+
+				pinctrl_lcd_rgb666: pinctrl_lcd_rgb666 {
+					pinmux = <PIN_PC10__LCDDAT2>,
+						 <PIN_PC11__LCDDAT3>,
+						 <PIN_PC12__LCDDAT4>,
+						 <PIN_PC13__LCDDAT5>,
+						 <PIN_PC14__LCDDAT6>,
+						 <PIN_PC15__LCDDAT7>,
+						 <PIN_PC16__LCDDAT10>,
+						 <PIN_PC17__LCDDAT11>,
+						 <PIN_PC18__LCDDAT12>,
+						 <PIN_PC19__LCDDAT13>,
+						 <PIN_PC20__LCDDAT14>,
+						 <PIN_PC21__LCDDAT15>,
+						 <PIN_PC22__LCDDAT18>,
+						 <PIN_PC23__LCDDAT19>,
+						 <PIN_PC24__LCDDAT20>,
+						 <PIN_PC25__LCDDAT21>,
+						 <PIN_PC26__LCDDAT22>,
+						 <PIN_PC27__LCDDAT23>;
+					bias-disable;
+				};
+
+				pinctrl_lcd_pwm: pinctrl_lcd_pwm {
+					pinmux = <PIN_PC28__LCDPWM>;
+					bias-disable;
+				};
+
+				pinctrl_isc_base: isc_base {
+					pinmux = <PIN_PC4__ISC_PCK>,
+						 <PIN_PC5__ISC_VSYNC>,
+						 <PIN_PC6__ISC_HSYNC>,
+						 <PIN_PC7__ISC_MCK>;
+					bias-disable;
+				};
+
+
+				/*
+				 * The ADTRG pin can work on any edge type.
+				 * In here it's being pulled up, so need to
+				 * connect it to ground to get an edge e.g.
+				 * Trigger can be configured on falling, rise
+				 * or any edge, and the pull-up can be changed
+				 * to pull-down or left floating according to
+				 * needs.
+				 */
+				pinctrl_adtrg_default: adtrg_default {
+					pinmux = <PIN_PD31__ADTRG>;
+					bias-pull-up;
+				};
+
+				pinctrl_charger_chglev: charger_chglev {
+					pinmux = <PIN_PA12__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_charger_irq: charger_irq {
+					pinmux = <PIN_PB13__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_charger_lbo: charger_lbo {
+					pinmux = <PIN_PC8__GPIO>;
+					bias-pull-up;
+				};
+
+				pinctrl_classd_default: classd_default {
+					pinmux = <PIN_PB1__CLASSD_R0>,
+						 <PIN_PB2__CLASSD_R1>,
+						 <PIN_PB3__CLASSD_R2>,
+						 <PIN_PB4__CLASSD_R3>;
+					bias-pull-up;
+				};
+
+				pinctrl_flx0_default: flx0_default {
+					pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+						 <PIN_PB29__FLEXCOM0_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_flx4_default: flx4_default {
+					pinmux = <PIN_PD12__FLEXCOM4_IO0>,
+						 <PIN_PD13__FLEXCOM4_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_i2c0_default: i2c0_default {
+					pinmux = <PIN_PD21__TWD0>,
+						 <PIN_PD22__TWCK0>;
+					bias-disable;
+				};
+
+				pinctrl_i2c1_default: i2c1_default {
+					pinmux = <PIN_PD4__TWD1>,
+						 <PIN_PD5__TWCK1>;
+					bias-disable;
+				};
+
+				pinctrl_key_gpio_default: key_gpio_default {
+					pinmux = <PIN_PB9__GPIO>;
+					bias-pull-up;
+				};
+
+				pinctrl_macb0_default: macb0_default {
+					pinmux = <PIN_PB14__GTXCK>,
+						 <PIN_PB15__GTXEN>,
+						 <PIN_PB16__GRXDV>,
+						 <PIN_PB17__GRXER>,
+						 <PIN_PB18__GRX0>,
+						 <PIN_PB19__GRX1>,
+						 <PIN_PB20__GTX0>,
+						 <PIN_PB21__GTX1>,
+						 <PIN_PB22__GMDC>,
+						 <PIN_PB23__GMDIO>;
+					bias-disable;
+				};
+
+				pinctrl_macb0_phy_irq: macb0_phy_irq {
+					pinmux = <PIN_PC9__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_pdmic_default: pdmic_default {
+					pinmux = <PIN_PB26__PDMIC_DAT>,
+						<PIN_PB27__PDMIC_CLK>;
+					bias-disable;
+				};
+
+				pinctrl_sdmmc0_default: sdmmc0_default {
+					cmd_data {
+						pinmux = <PIN_PA1__SDMMC0_CMD>,
+							 <PIN_PA2__SDMMC0_DAT0>,
+							 <PIN_PA3__SDMMC0_DAT1>,
+							 <PIN_PA4__SDMMC0_DAT2>,
+							 <PIN_PA5__SDMMC0_DAT3>,
+							 <PIN_PA6__SDMMC0_DAT4>,
+							 <PIN_PA7__SDMMC0_DAT5>,
+							 <PIN_PA8__SDMMC0_DAT6>,
+							 <PIN_PA9__SDMMC0_DAT7>;
+						bias-disable;
+					};
+
+					ck_cd_rstn_vddsel {
+						pinmux = <PIN_PA0__SDMMC0_CK>,
+							 <PIN_PA10__SDMMC0_RSTN>,
+							 <PIN_PA11__SDMMC0_VDDSEL>,
+							 <PIN_PA13__SDMMC0_CD>;
+						bias-disable;
+					};
+				};
+
+				pinctrl_sdmmc1_default: sdmmc1_default {
+					cmd_data {
+						pinmux = <PIN_PA28__SDMMC1_CMD>,
+							 <PIN_PA18__SDMMC1_DAT0>,
+							 <PIN_PA19__SDMMC1_DAT1>,
+							 <PIN_PA20__SDMMC1_DAT2>,
+							 <PIN_PA21__SDMMC1_DAT3>;
+						bias-pull-up;
+					};
+
+					conf-ck_cd {
+						pinmux = <PIN_PA22__SDMMC1_CK>;
+						bias-disable;
+					};
+				};
+
+				/* Pin definition SPI 0 Peripheral A */
+
+				pinctrl_spi0_default: spi0_default {
+					pinmux = <PIN_PA14__SPI0_SPCK>,
+							 <PIN_PA15__SPI0_MOSI>,
+							 <PIN_PA16__SPI0_MISO>,
+							 <PIN_PA17__SPI0_NPCS0>;
+					bias-disable;
+				};
+
+				/* Pin definition SPI 1 Peripheral D */
+
+				pinctrl_spi1_default: spi1_default {
+					pinmux = <PIN_PC1__SPI1_SPCK>,
+							<PIN_PC2__SPI1_MOSI>,
+							<PIN_PC3__SPI1_MISO>,
+							<PIN_PC4__SPI1_NPCS0>,
+							<PIN_PC5__SPI1_NPCS1>;
+					bias-disable;
+				};
+
+				pinctrl_uart1_default: uart1_default {
+					pinmux = <PIN_PD2__URXD1>,
+						 <PIN_PD3__UTXD1>;
+					bias-disable;
+				};
+
+				pinctrl_uart3_default: uart3_default {
+					pinmux = <PIN_PB11__URXD3>,
+						 <PIN_PB12__UTXD3>;
+					bias-disable;
+				};
+
+				pinctrl_usb_default: usb_default {
+					pinmux = <PIN_PB10__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_usba_vbus: usba_vbus {
+					pinmux = <PIN_PA31__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_pwm0_pwm2_default: pwm0_pwm2_default {
+					pinmux = <PIN_PB5__PWMH2>,
+						 <PIN_PB6__PWML2>;
+					bias-pull-up;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/acme-roadrunner-fbtft.dts b/arch/arm/boot/dts/acme-roadrunner-fbtft.dts
new file mode 100644
index 000000000..0405152f0
--- /dev/null
+++ b/arch/arm/boot/dts/acme-roadrunner-fbtft.dts
@@ -0,0 +1,473 @@
+/*
+ * Device Tree file for Acme Systems for RoadRunner SOM 
+ * Test with small SPI display
+ *
+ *  Copyright (C) 2015 Atmel,
+ *                2015 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *                2020 Sergio Tanzilli <tanzilli@acmesystems.it>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/gpio/gpio.h>
+
+
+
+/ {
+	model = "Acme Systems SAMA5D2 Roadrunner";
+	compatible = "atmel,sama5d2-roadrunner", "atmel,sama5d27","atmel,sama5d2", "atmel,sama5";
+
+	bootargs = "mem=256M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait consoleblank=0";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		usb0: gadget@300000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+
+		usb1: ohci@400000 {
+			num-ports = <3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb_default>;
+			status = "okay";
+		};
+
+		usb2: ehci@500000 {
+			status = "okay";
+		};
+
+		sdmmc1: sdio-host@b0000000 {
+			bus-width = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc1_default>;
+			non-removable;
+			status = "okay"; /* conflict with qspi0 */
+		};
+
+		apb {
+		
+		
+			/* Both displays on SPI 1 port */
+
+			spi1: spi@fc000000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_spi1_default>;
+				status = "okay";
+
+				/* First display */
+
+				device@0 {
+					rotate = <90>;
+					bgr;
+					fps = <30>;
+					compatible = "ilitek,ili9341";
+					spi-max-frequency = <50000000>;   
+					reg = <0>;
+					regwidth = <8>;
+					buswidth = <8>;
+					verbose = <3>;
+					reset-gpios = <&pioA PIN_PA13 0>;
+					dc-gpios = <&pioA PIN_PA12 0>;
+				};
+
+				/* Second display */
+
+				device@1 {
+					rotate = <90>;
+					bgr;
+					fps = <30>;
+					compatible = "ilitek,ili9341";
+					spi-max-frequency = <50000000>;   
+					reg = <1>;
+					regwidth = <8>;
+					buswidth = <8>;
+					verbose = <3>;
+					reset-gpios = <&pioA PIN_PA11 0>;
+					dc-gpios = <&pioA PIN_PA8 0>;
+				};
+			};
+
+			macb0: ethernet@f8008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+				phy-mode = "rmii";
+				status = "okay";
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+					interrupt-parent = <&pioA>;
+					interrupts = <73 IRQ_TYPE_LEVEL_LOW>;
+					/*interrupts = <PIN_PC9 IRQ_TYPE_LEVEL_LOW>;*/
+				};
+			};
+
+			tcb0: timer@f800c000 {
+				timer0: timer@0 {
+					compatible = "atmel,tcb-timer";
+					reg = <0>;
+				};
+
+				timer1: timer@1 {
+					compatible = "atmel,tcb-timer";
+					reg = <1>;
+				};
+			};
+
+			uart1: serial@f8020000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_default>;
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				status = "okay";
+			};
+
+			shdwc@f8048010 {
+				atmel,shdwc-debouncer = <976>;
+				atmel,wakeup-rtc-timer;
+
+				input@0 {
+					reg = <0>;
+					atmel,wakeup-type = "low";
+				};
+			};
+
+			watchdog@f8048040 {
+				status = "okay";
+			};
+
+			vddin_3v3: fixed-regulator-vddin_3v3 {
+				compatible = "regulator-fixed";
+
+				regulator-name = "VDDIN_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				status = "okay";
+			};
+
+			vddana: fixed-regulator-vddana {
+				compatible = "regulator-fixed";
+
+				regulator-name = "VDDANA";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				vin-supply = <&vddin_3v3>;
+				status = "okay";
+			};
+
+			advref: fixed-regulator-advref {
+				compatible = "regulator-fixed";
+
+				regulator-name = "advref";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				vin-supply = <&vddana>;
+				status = "okay";
+			};
+
+			adc: adc@fc030000 {
+				vddana-supply = <&vddana>; 
+				vref-supply =  <&vddana>; 
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_adc_default>;
+				
+				atmel,adc-clock-rate=<1000000>;
+				atmel,adc-ts-wires=<4>;
+				atmel,adc-ts-pressure-threshold=<10000>;
+				
+				status = "okay";
+			};
+
+			pinctrl@fc038000 {
+				/*
+				 * There is no real pinmux for ADC, if the pin
+				 * is not requested by another peripheral then
+				 * the muxing is done when channel is enabled.
+				 * Requesting pins for ADC is GPIO is
+				 * encouraged to prevent conflicts and to
+				 * disable bias in order to be in the same
+				 * state when the pin is not muxed to the adc.
+				 */
+				pinctrl_adc_default: adc_default {
+					pinmux = <PIN_PD19__GPIO>,
+						<PIN_PD20__GPIO>,
+						<PIN_PD21__GPIO>,
+						<PIN_PD22__GPIO>,
+						<PIN_PD23__GPIO>,
+						<PIN_PD24__GPIO>,
+						<PIN_PD25__GPIO>,
+						<PIN_PD26__GPIO>,
+						<PIN_PD27__GPIO>,
+						<PIN_PD28__GPIO>,
+						<PIN_PD29__GPIO>,
+						<PIN_PD30__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_can0_default: can0_default {
+					pinmux = <PIN_PC10__CANTX0>,
+						 <PIN_PC11__CANRX0>;
+					bias-disable;
+				};
+
+				pinctrl_can1_default: can1_default {
+					pinmux = <PIN_PC26__CANTX1>,
+						 <PIN_PC27__CANRX1>;
+					bias-disable;
+				};
+
+				/*
+				 * The ADTRG pin can work on any edge type.
+				 * In here it's being pulled up, so need to
+				 * connect it to ground to get an edge e.g.
+				 * Trigger can be configured on falling, rise
+				 * or any edge, and the pull-up can be changed
+				 * to pull-down or left floating according to
+				 * needs.
+				 */
+				pinctrl_adtrg_default: adtrg_default {
+					pinmux = <PIN_PD31__ADTRG>;
+					bias-pull-up;
+				};
+
+				pinctrl_charger_chglev: charger_chglev {
+					pinmux = <PIN_PA12__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_charger_irq: charger_irq {
+					pinmux = <PIN_PB13__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_charger_lbo: charger_lbo {
+					pinmux = <PIN_PC8__GPIO>;
+					bias-pull-up;
+				};
+
+				pinctrl_classd_default: classd_default {
+					pinmux = <PIN_PB1__CLASSD_R0>,
+						 <PIN_PB2__CLASSD_R1>,
+						 <PIN_PB3__CLASSD_R2>,
+						 <PIN_PB4__CLASSD_R3>;
+					bias-pull-up;
+				};
+
+				pinctrl_flx0_default: flx0_default {
+					pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+						 <PIN_PB29__FLEXCOM0_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_flx4_default: flx4_default {
+					pinmux = <PIN_PD12__FLEXCOM4_IO0>,
+						 <PIN_PD13__FLEXCOM4_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_i2c0_default: i2c0_default {
+					pinmux = <PIN_PD21__TWD0>,
+						 <PIN_PD22__TWCK0>;
+					bias-disable;
+				};
+
+				pinctrl_i2c1_default: i2c1_default {
+					pinmux = <PIN_PD4__TWD1>,
+						 <PIN_PD5__TWCK1>;
+					bias-disable;
+				};
+
+				pinctrl_key_gpio_default: key_gpio_default {
+					pinmux = <PIN_PB9__GPIO>;
+					bias-pull-up;
+				};
+
+				pinctrl_macb0_default: macb0_default {
+					pinmux = <PIN_PB14__GTXCK>,
+						 <PIN_PB15__GTXEN>,
+						 <PIN_PB16__GRXDV>,
+						 <PIN_PB17__GRXER>,
+						 <PIN_PB18__GRX0>,
+						 <PIN_PB19__GRX1>,
+						 <PIN_PB20__GTX0>,
+						 <PIN_PB21__GTX1>,
+						 <PIN_PB22__GMDC>,
+						 <PIN_PB23__GMDIO>;
+					bias-disable;
+				};
+
+				pinctrl_macb0_phy_irq: macb0_phy_irq {
+					pinmux = <PIN_PC9__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_pdmic_default: pdmic_default {
+					pinmux = <PIN_PB26__PDMIC_DAT>,
+						<PIN_PB27__PDMIC_CLK>;
+					bias-disable;
+				};
+
+				pinctrl_sdmmc0_default: sdmmc0_default {
+					cmd_data {
+						pinmux = <PIN_PA1__SDMMC0_CMD>,
+							 <PIN_PA2__SDMMC0_DAT0>,
+							 <PIN_PA3__SDMMC0_DAT1>,
+							 <PIN_PA4__SDMMC0_DAT2>,
+							 <PIN_PA5__SDMMC0_DAT3>,
+							 <PIN_PA6__SDMMC0_DAT4>,
+							 <PIN_PA7__SDMMC0_DAT5>,
+							 <PIN_PA8__SDMMC0_DAT6>,
+							 <PIN_PA9__SDMMC0_DAT7>;
+						bias-disable;
+					};
+
+					ck_cd_rstn_vddsel {
+						pinmux = <PIN_PA0__SDMMC0_CK>,
+							 <PIN_PA10__SDMMC0_RSTN>,
+							 <PIN_PA11__SDMMC0_VDDSEL>,
+							 <PIN_PA13__SDMMC0_CD>;
+						bias-disable;
+					};
+				};
+
+				pinctrl_sdmmc1_default: sdmmc1_default {
+					cmd_data {
+						pinmux = <PIN_PA28__SDMMC1_CMD>,
+							 <PIN_PA18__SDMMC1_DAT0>,
+							 <PIN_PA19__SDMMC1_DAT1>,
+							 <PIN_PA20__SDMMC1_DAT2>,
+							 <PIN_PA21__SDMMC1_DAT3>;
+						bias-pull-up;
+					};
+
+					conf-ck_cd {
+						pinmux = <PIN_PA22__SDMMC1_CK>;
+						bias-disable;
+					};
+				};
+
+				/* Pin definition SPI 0 Peripheral A */
+
+				pinctrl_spi0_default: spi0_default {
+					pinmux = <PIN_PA14__SPI0_SPCK>,
+							 <PIN_PA15__SPI0_MOSI>,
+							 <PIN_PA16__SPI0_MISO>,
+							 <PIN_PA17__SPI0_NPCS0>;
+					bias-disable;
+				};
+
+				/* Pin definition SPI 1 Peripheral D */
+
+				pinctrl_spi1_default: spi1_default {
+					pinmux = <PIN_PC1__SPI1_SPCK>,
+							<PIN_PC2__SPI1_MOSI>,
+							<PIN_PC3__SPI1_MISO>,
+							<PIN_PC4__SPI1_NPCS0>,
+							<PIN_PC5__SPI1_NPCS1>;
+					bias-disable;
+				};
+
+				pinctrl_uart1_default: uart1_default {
+					pinmux = <PIN_PD2__URXD1>,
+						 <PIN_PD3__UTXD1>;
+					bias-disable;
+				};
+
+				pinctrl_uart3_default: uart3_default {
+					pinmux = <PIN_PB11__URXD3>,
+						 <PIN_PB12__UTXD3>;
+					bias-disable;
+				};
+
+				pinctrl_usb_default: usb_default {
+					pinmux = <PIN_PB10__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_usba_vbus: usba_vbus {
+					pinmux = <PIN_PA31__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_pwm0_pwm2_default: pwm0_pwm2_default {
+					pinmux = <PIN_PB5__PWMH2>,
+						 <PIN_PB6__PWML2>;
+					bias-pull-up;
+				};
+			};
+
+			classd: classd@fc048000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_classd_default>;
+				atmel,pwm-type = "diff";
+				atmel,non-overlap-time = <10>;
+				status = "disabled";
+			};
+
+			can1: can@fc050000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_can1_default>;
+				status = "disabled";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/acme-roadrunner-isc-ov5640.dts b/arch/arm/boot/dts/acme-roadrunner-isc-ov5640.dts
new file mode 100644
index 000000000..73ee7610d
--- /dev/null
+++ b/arch/arm/boot/dts/acme-roadrunner-isc-ov5640.dts
@@ -0,0 +1,348 @@
+/*
+ * Device Tree file for Acme Systems RoadRunner S
+ * ISC sensor
+ */
+
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Acme Systems SAMA5D2 Roadrunner";
+	compatible = "atmel,sama5d2-roadrunner", "atmel,sama5d27","atmel,sama5d2", "atmel,sama5";
+
+	bootargs = "mem=256M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait consoleblank=0";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		usb0: gadget@300000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+
+		usb1: ohci@400000 {
+			num-ports = <3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb_default>;
+			status = "okay";
+		};
+
+		usb2: ehci@500000 {
+			status = "okay";
+		};
+
+		sdmmc1: sdio-host@b0000000 {
+			bus-width = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc1_default>;
+			non-removable;
+			status = "okay"; /* conflict with qspi0 */
+		};
+
+		apb {
+
+
+			/* Omnivision OV7670 (0.3 MPixel) */
+			/*
+
+			i2c1: i2c@fc028000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1_default>;
+				status = "okay";
+
+				ov7670: camera@21 {
+					compatible = "ovti,ov7670";
+					reg = <0x21>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_sensor_power &pinctrl_sensor_reset>;
+					clocks = <&isc>;
+					clock-names = "xclk";
+					assigned-clocks = <&isc>;
+					assigned-clock-rates = <24000000>;
+					reset-gpios = <&pioA PIN_PB11 GPIO_ACTIVE_LOW>;
+					powerdown-gpios = <&pioA PIN_PB12 GPIO_ACTIVE_HIGH>;
+
+					port {
+						ov7670_0: endpoint {
+							remote-endpoint = <&isc_0>;
+							hsync-active = <1>;
+							vsync-active = <1>;
+							pclk-sample = <1>;
+						};
+					};
+				};
+	
+			};
+
+			isc: isc@f0008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit>;
+				status = "okay";
+
+				port {
+					isc_0: endpoint@0 {
+						remote-endpoint = <&ov7670_0>;
+						hsync-active = <1>;
+						vsync-active = <0>;
+						pclk-sample = <1>;
+					};
+				};
+			};
+
+			*/
+			
+
+			/* Omnivision OV5640 (5Mpixel) */
+			/* https://github.com/linux4sam/dt-overlay-at91/blob/master/sama5d27_wlsom1_ek/sama5d27_wlsom1_ek_ov5640.dtso */
+
+			i2c1: i2c@fc028000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1_default>;
+				status = "okay";
+
+				ov5640: camera@3c {
+					compatible = "ovti,ov5640";
+					reg = <0x3c>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_sensor_power &pinctrl_sensor_reset>;
+					clocks = <&isc>;
+					clock-names = "xclk";
+					assigned-clocks = <&isc>;
+					assigned-clock-rates = <25000000>;
+					reset-gpios = <&pioA PIN_PB11 GPIO_ACTIVE_LOW>;
+					powerdown-gpios = <&pioA PIN_PB12 GPIO_ACTIVE_HIGH>;
+
+					port {
+						ov5640_0: endpoint {
+							remote-endpoint = <&isc_0>;
+							bus-width = <8>;
+							data-shift = <2>;
+							hsync-active = <1>;
+							vsync-active = <1>;
+							pclk-sample = <1>;
+						};
+					};
+				};
+	
+			};
+
+
+			isc: isc@f0008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit>;
+				status = "okay";
+
+				port {
+					isc_0: endpoint@0 {
+						remote-endpoint = <&ov5640_0>;
+						bus-width = <8>;
+						data-shift = <2>;
+						hsync-active = <0>;
+						vsync-active = <0>;
+						pclk-sample = <1>;
+					};
+				};
+			};
+
+
+			macb0: ethernet@f8008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+				phy-mode = "rmii";
+				status = "okay";
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+					interrupt-parent = <&pioA>;
+					interrupts = <73 IRQ_TYPE_LEVEL_LOW>;
+					/*interrupts = <PIN_PC9 IRQ_TYPE_LEVEL_LOW>;*/
+				};
+			};
+
+			tcb0: timer@f800c000 {
+				timer0: timer@0 {
+					compatible = "atmel,tcb-timer";
+					reg = <0>;
+				};
+
+				timer1: timer@1 {
+					compatible = "atmel,tcb-timer";
+					reg = <1>;
+				};
+			};
+
+			uart1: serial@f8020000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_default>;
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				status = "okay";
+			};
+
+			shdwc@f8048010 {
+				atmel,shdwc-debouncer = <976>;
+				atmel,wakeup-rtc-timer;
+
+				input@0 {
+					reg = <0>;
+					atmel,wakeup-type = "low";
+				};
+			};
+
+			watchdog@f8048040 {
+				status = "okay";
+			};
+
+			pinctrl@fc038000 {
+				pinctrl_isc_base: isc_base {
+					pinmux = <PIN_PC4__ISC_PCK>,
+						 <PIN_PC5__ISC_VSYNC>,
+						 <PIN_PC6__ISC_HSYNC>,
+						 <PIN_PC7__ISC_MCK>;
+					bias-disable;
+				};
+
+				pinctrl_isc_data_8bit: isc_data_8bit {
+					pinmux = <PIN_PB25__ISC_D11>,
+						 <PIN_PB24__ISC_D10>,
+						 <PIN_PC3__ISC_D9>,
+						 <PIN_PC2__ISC_D8>,
+						 <PIN_PC1__ISC_D7>,
+						 <PIN_PC0__ISC_D6>,
+						 <PIN_PB31__ISC_D5>,
+						 <PIN_PB30__ISC_D4>;
+					bias-disable;
+				};
+
+
+				pinctrl_sensor_power: sensor_power {
+					pinmux = <PIN_PB12__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_sensor_reset: sensor_reset {
+					pinmux = <PIN_PB11__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_i2c0_default: i2c0_default {
+					pinmux = <PIN_PD21__TWD0>,
+						 <PIN_PD22__TWCK0>;
+					bias-disable;
+				};
+
+				pinctrl_i2c1_default: i2c1_default {
+					pinmux = <PIN_PD4__TWD1>,
+						 <PIN_PD5__TWCK1>;
+					bias-disable;
+				};
+
+				pinctrl_macb0_default: macb0_default {
+					pinmux = <PIN_PB14__GTXCK>, 
+						 <PIN_PB15__GTXEN>,
+						 <PIN_PB16__GRXDV>,
+						 <PIN_PB17__GRXER>,
+						 <PIN_PB18__GRX0>,
+						 <PIN_PB19__GRX1>,
+						 <PIN_PB20__GTX0>,
+						 <PIN_PB21__GTX1>,
+						 <PIN_PB22__GMDC>,
+						 <PIN_PB23__GMDIO>;
+					bias-disable;
+				};
+
+				pinctrl_macb0_phy_irq: macb0_phy_irq {
+					pinmux = <PIN_PC9__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_sdmmc0_default: sdmmc0_default {
+					cmd_data {
+						pinmux = <PIN_PA1__SDMMC0_CMD>,
+							 <PIN_PA2__SDMMC0_DAT0>,
+							 <PIN_PA3__SDMMC0_DAT1>,
+							 <PIN_PA4__SDMMC0_DAT2>,
+							 <PIN_PA5__SDMMC0_DAT3>,
+							 <PIN_PA6__SDMMC0_DAT4>,
+							 <PIN_PA7__SDMMC0_DAT5>,
+							 <PIN_PA8__SDMMC0_DAT6>,
+							 <PIN_PA9__SDMMC0_DAT7>;
+						bias-disable;
+					};
+
+					ck_cd_rstn_vddsel {
+						pinmux = <PIN_PA0__SDMMC0_CK>,
+							 <PIN_PA10__SDMMC0_RSTN>,
+							 <PIN_PA11__SDMMC0_VDDSEL>,
+							 <PIN_PA13__SDMMC0_CD>;
+						bias-disable;
+					};
+				};
+
+				pinctrl_sdmmc1_default: sdmmc1_default {
+					cmd_data {
+						pinmux = <PIN_PA28__SDMMC1_CMD>,
+							 <PIN_PA18__SDMMC1_DAT0>,
+							 <PIN_PA19__SDMMC1_DAT1>,
+							 <PIN_PA20__SDMMC1_DAT2>,
+							 <PIN_PA21__SDMMC1_DAT3>;
+						bias-pull-up;
+					};
+
+					conf-ck_cd {
+						pinmux = <PIN_PA22__SDMMC1_CK>;
+						bias-disable;
+					};
+				};
+
+				pinctrl_uart1_default: uart1_default {
+					pinmux = <PIN_PD2__URXD1>,
+						 <PIN_PD3__UTXD1>;
+					bias-disable;
+				};
+
+				pinctrl_uart3_default: uart3_default {
+					pinmux = <PIN_PB11__URXD3>,
+						 <PIN_PB12__UTXD3>;
+					bias-disable;
+				};
+
+				pinctrl_usb_default: usb_default {
+					pinmux = <PIN_PB10__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_usba_vbus: usba_vbus {
+					pinmux = <PIN_PA31__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_pwm0_pwm2_default: pwm0_pwm2_default {
+					pinmux = <PIN_PB5__PWMH2>,
+						 <PIN_PB6__PWML2>;
+					bias-pull-up;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/acme-roadrunner-isc-ov7670.dts b/arch/arm/boot/dts/acme-roadrunner-isc-ov7670.dts
new file mode 100644
index 000000000..06f1e967b
--- /dev/null
+++ b/arch/arm/boot/dts/acme-roadrunner-isc-ov7670.dts
@@ -0,0 +1,248 @@
+/*
+ * Device Tree file for Acme Systems RoadRunner S
+ * Camera sensor on ISC interface
+ * OV7670
+ */
+
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Acme Systems SAMA5D2 Roadrunner";
+	compatible = "atmel,sama5d2-roadrunner", "atmel,sama5d27","atmel,sama5d2", "atmel,sama5";
+
+	bootargs = "mem=256M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait consoleblank=0";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		usb0: gadget@300000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+
+		usb1: ohci@400000 {
+			num-ports = <3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb_default>;
+			status = "okay";
+		};
+
+		usb2: ehci@500000 {
+			status = "okay";
+		};
+
+		sdmmc1: sdio-host@b0000000 {
+			bus-width = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc1_default>;
+			non-removable;
+			status = "okay";
+		};
+
+		apb {
+			/* Omnivision OV7670 (0.3 MPixel) */
+	
+			i2c1: i2c@fc028000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1_default>;
+				status = "okay";
+
+				ov7670: camera@21 {
+					compatible = "ovti,ov7670";
+					reg = <0x21>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_sensor_power &pinctrl_sensor_reset>;
+					clocks = <&isc>;
+					clock-names = "xclk";
+					assigned-clocks = <&isc>;
+					assigned-clock-rates = <24000000>;
+					reset-gpios = <&pioA PIN_PB11 GPIO_ACTIVE_LOW>;
+					powerdown-gpios = <&pioA PIN_PB12 GPIO_ACTIVE_HIGH>;
+
+					port {
+						ov7670_0: endpoint {
+							remote-endpoint = <&isc_0>;
+							hsync-active = <1>;
+							vsync-active = <1>;
+							pclk-sample = <1>;
+						};
+					};
+				};
+	
+			};
+
+			isc: isc@f0008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit>;
+				status = "okay";
+
+				port {
+					isc_0: endpoint@0 {
+						remote-endpoint = <&ov7670_0>;
+						hsync-active = <1>;
+						vsync-active = <0>;
+						pclk-sample = <1>;
+					};
+				};
+			};
+
+
+			macb0: ethernet@f8008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+				phy-mode = "rmii";
+				status = "okay";
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+					interrupt-parent = <&pioA>;
+					interrupts = <73 IRQ_TYPE_LEVEL_LOW>;
+					/*interrupts = <PIN_PC9 IRQ_TYPE_LEVEL_LOW>;*/
+				};
+			};
+
+			tcb0: timer@f800c000 {
+				timer0: timer@0 {
+					compatible = "atmel,tcb-timer";
+					reg = <0>;
+				};
+
+				timer1: timer@1 {
+					compatible = "atmel,tcb-timer";
+					reg = <1>;
+				};
+			};
+
+			uart1: serial@f8020000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_default>;
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				status = "okay";
+			};
+
+			shdwc@f8048010 {
+				atmel,shdwc-debouncer = <976>;
+				atmel,wakeup-rtc-timer;
+
+				input@0 {
+					reg = <0>;
+					atmel,wakeup-type = "low";
+				};
+			};
+
+			watchdog@f8048040 {
+				status = "okay";
+			};
+
+			pinctrl@fc038000 {
+				pinctrl_isc_base: isc_base {
+					pinmux = <PIN_PC4__ISC_PCK>,
+						 <PIN_PC5__ISC_VSYNC>,
+						 <PIN_PC6__ISC_HSYNC>,
+						 <PIN_PC7__ISC_MCK>;
+					bias-disable;
+				};
+
+				pinctrl_isc_data_8bit: isc_data_8bit {
+					pinmux = <PIN_PB25__ISC_D11>,
+						 <PIN_PB24__ISC_D10>,
+						 <PIN_PC3__ISC_D9>,
+						 <PIN_PC2__ISC_D8>,
+						 <PIN_PC1__ISC_D7>,
+						 <PIN_PC0__ISC_D6>,
+						 <PIN_PB31__ISC_D5>,
+						 <PIN_PB30__ISC_D4>;
+					bias-disable;
+				};
+
+
+				pinctrl_sensor_power: sensor_power {
+					pinmux = <PIN_PB12__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_sensor_reset: sensor_reset {
+					pinmux = <PIN_PB11__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_i2c1_default: i2c1_default {
+					pinmux = <PIN_PD4__TWD1>,
+						 <PIN_PD5__TWCK1>;
+					bias-disable;
+				};
+
+				pinctrl_macb0_default: macb0_default {
+					pinmux = <PIN_PB14__GTXCK>, 
+						 <PIN_PB15__GTXEN>,
+						 <PIN_PB16__GRXDV>,
+						 <PIN_PB17__GRXER>,
+						 <PIN_PB18__GRX0>,
+						 <PIN_PB19__GRX1>,
+						 <PIN_PB20__GTX0>,
+						 <PIN_PB21__GTX1>,
+						 <PIN_PB22__GMDC>,
+						 <PIN_PB23__GMDIO>;
+					bias-disable;
+				};
+
+				pinctrl_macb0_phy_irq: macb0_phy_irq {
+					pinmux = <PIN_PC9__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_sdmmc1_default: sdmmc1_default {
+					cmd_data {
+						pinmux = <PIN_PA28__SDMMC1_CMD>,
+							 <PIN_PA18__SDMMC1_DAT0>,
+							 <PIN_PA19__SDMMC1_DAT1>,
+							 <PIN_PA20__SDMMC1_DAT2>,
+							 <PIN_PA21__SDMMC1_DAT3>;
+						bias-pull-up;
+					};
+
+					conf-ck_cd {
+						pinmux = <PIN_PA22__SDMMC1_CK>;
+						bias-disable;
+					};
+				};
+
+				pinctrl_uart1_default: uart1_default {
+					pinmux = <PIN_PD2__URXD1>,
+						 <PIN_PD3__UTXD1>;
+					bias-disable;
+				};
+
+				pinctrl_usb_default: usb_default {
+					pinmux = <PIN_PB10__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_usba_vbus: usba_vbus {
+					pinmux = <PIN_PA31__GPIO>;
+					bias-disable;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/acme-roadrunner-oyster.dts b/arch/arm/boot/dts/acme-roadrunner-oyster.dts
new file mode 100644
index 000000000..9f130209a
--- /dev/null
+++ b/arch/arm/boot/dts/acme-roadrunner-oyster.dts
@@ -0,0 +1,274 @@
+/*
+ * acme_roadrunner-oyster.dts - Device Tree file for Acme Systems
+ * RoadRunner SOM 
+ *
+ */
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Acme Systems SAMA5D2 Roadrunner";
+	compatible = "atmel,sama5d2-roadrunner", "atmel,sama5d27","atmel,sama5d2", "atmel,sama5";
+
+	bootargs = "mem=256M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait consoleblank=0";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		usb0: gadget@300000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+		};
+
+		usb1: ohci@400000 {
+			num-ports = <3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb_default>;
+			status = "okay";
+		};
+
+		usb2: ehci@500000 {
+			status = "okay";
+		};
+
+		/* Enable MMC0 bus */
+
+		sdmmc0: sdio-host@a0000000 {
+			bus-width = <4>;
+			pinctrl-names = "default";
+			no-1-8-v;
+			non-removable;  
+			pinctrl-0 = <&pinctrl_sdmmc0_default>;
+			status = "okay";
+		};
+
+		/* MMC1 remains disabled to set free the Class-D lines */
+
+		sdmmc1: sdio-host@b0000000 {
+			bus-width = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc1_default>;
+		};
+		
+
+		apb {
+			pdmic@f8018000 {
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_pdmic_default>;
+					atmel,model = "PDMIC @ sama5d2_xplained";
+					atmel,mic-min-freq = <1000000>;
+					atmel,mic-max-freq = <3246000>;
+					atmel,mic-offset = <0x0>;
+					status = "okay";
+			};
+			
+			macb0: ethernet@f8008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+				phy-mode = "rmii";
+				status = "okay";
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+					interrupt-parent = <&pioA>;
+					interrupts = <73 IRQ_TYPE_LEVEL_LOW>;
+					/*interrupts = <PIN_PC9 IRQ_TYPE_LEVEL_LOW>;*/
+				};
+			};
+
+			tcb0: timer@f800c000 {
+				timer0: timer@0 {
+					compatible = "atmel,tcb-timer";
+					reg = <0>;
+				};
+
+				timer1: timer@1 {
+					compatible = "atmel,tcb-timer";
+					reg = <1>;
+				};
+			};
+
+			/* Debug port */
+
+			uart1: serial@f8020000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_default>;
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				status = "okay";
+			};
+
+			i2c0: i2c@f8028000 {
+				dmas = <0>, <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c0_default>;
+				i2c-sda-hold-time-ns = <350>;
+				status = "okay";
+			};
+
+			spi0: spi@f8000000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_spi0_default>;
+				status = "okay";
+
+				device@0 {
+					rotate = <0>;
+					bgr;
+					fps = <30>;
+					compatible = "solomon,ssd1351";
+					spi-max-frequency = <20000000>;   
+					reg = <0>;
+					regwidth = <8>;
+					buswidth = <8>;
+					verbose = <3>;
+					reset-gpios = <&pioA PIN_PA9 0>;
+					dc-gpios = <&pioA PIN_PA12 0>;
+				};
+			};
+
+			shdwc@f8048010 {
+				atmel,shdwc-debouncer = <976>;
+				atmel,wakeup-rtc-timer;
+
+				input@0 {
+					reg = <0>;
+					atmel,wakeup-type = "low";
+				};
+			};
+
+			watchdog@f8048040 {
+				status = "okay";
+			};
+
+			classd: classd@fc048000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_classd_default>;
+				/*atmel,pwm-type = "diff";*/
+				atmel,pwm-type = "single";
+				atmel,non-overlap-time = <10>;
+				status = "okay";
+			};
+
+			pinctrl@fc038000 {
+				pinctrl_pdmic_default: pdmic_default {
+					pinmux = <PIN_PB26__PDMIC_DAT>,
+						<PIN_PB27__PDMIC_CLK>;
+					bias-disable;
+				};
+
+
+				pinctrl_i2c0_default: i2c0_default {
+					pinmux = <PIN_PD21__TWD0>,
+						 <PIN_PD22__TWCK0>;
+					bias-disable;
+				};
+
+				pinctrl_macb0_default: macb0_default {
+					pinmux = <PIN_PB14__GTXCK>,
+						 <PIN_PB15__GTXEN>,
+						 <PIN_PB16__GRXDV>,
+						 <PIN_PB17__GRXER>,
+						 <PIN_PB18__GRX0>,
+						 <PIN_PB19__GRX1>,
+						 <PIN_PB20__GTX0>,
+						 <PIN_PB21__GTX1>,
+						 <PIN_PB22__GMDC>,
+						 <PIN_PB23__GMDIO>;
+					bias-disable;
+				};
+
+				pinctrl_macb0_phy_irq: macb0_phy_irq {
+					pinmux = <PIN_PC9__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_sdmmc0_default: sdmmc0_default {
+					cmd_data {
+						pinmux = <PIN_PA1__SDMMC0_CMD>,
+							 <PIN_PA2__SDMMC0_DAT0>,
+							 <PIN_PA3__SDMMC0_DAT1>,
+							 <PIN_PA4__SDMMC0_DAT2>,
+							 <PIN_PA5__SDMMC0_DAT3>;
+						bias-disable;
+					};
+
+					ck_cd_rstn_vddsel {
+						pinmux = <PIN_PA0__SDMMC0_CK>,
+							 <PIN_PA13__SDMMC0_CD>;
+						bias-disable;
+					};
+				};
+
+
+				pinctrl_sdmmc1_default: sdmmc1_default {
+					cmd_data {
+						pinmux = <PIN_PA28__SDMMC1_CMD>,
+							 <PIN_PA18__SDMMC1_DAT0>,
+							 <PIN_PA19__SDMMC1_DAT1>,
+							 <PIN_PA20__SDMMC1_DAT2>,
+							 <PIN_PA21__SDMMC1_DAT3>;
+						bias-pull-up;
+					};
+
+					conf-ck_cd {
+						pinmux = <PIN_PA22__SDMMC1_CK>;
+						bias-disable;
+					};
+				};
+
+				pinctrl_spi0_default: spi0_default {
+					pinmux = <PIN_PA14__SPI0_SPCK>,
+							 <PIN_PA15__SPI0_MOSI>,
+							 <PIN_PA16__SPI0_MISO>,
+							 <PIN_PA17__SPI0_NPCS0>;
+					bias-disable;
+				};
+
+
+				pinctrl_uart1_default: uart1_default {
+					pinmux = <PIN_PD2__URXD1>,
+						 <PIN_PD3__UTXD1>;
+					bias-disable;
+				};
+
+				pinctrl_usb_default: usb_default {
+					pinmux = <PIN_PB10__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_usba_vbus: usba_vbus {
+					pinmux = <PIN_PA31__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_classd_default: classd_default {
+					pinmux = <PIN_PB1__CLASSD_R0>,
+							 <PIN_PB2__CLASSD_R1>,
+							 <PIN_PB3__CLASSD_R2>,
+							 <PIN_PB4__CLASSD_R3>,
+							 <PIN_PA28__CLASSD_L0>,
+							 <PIN_PA29__CLASSD_L1>,
+							 <PIN_PA30__CLASSD_L2>,
+							 <PIN_PA31__CLASSD_L3>;
+					bias-pull-up;
+				};
+			};
+			
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/acme-roadrunner-sdio.dts b/arch/arm/boot/dts/acme-roadrunner-sdio.dts
new file mode 100644
index 000000000..b9dfdc522
--- /dev/null
+++ b/arch/arm/boot/dts/acme-roadrunner-sdio.dts
@@ -0,0 +1,528 @@
+/*
+ * acme-roadrunner-sdio.dts - Device Tree file for Acme Systems
+ * RoadRunner SOM with SDIO on MMC0
+ *
+ *  Copyright (C) 2015 Atmel,
+ *                2015 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *                2020 Sergio Tanzilli <tanzilli@acmesystems.it>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/gpio/gpio.h>
+
+
+
+/ {
+	model = "Acme Systems SAMA5D2 Roadrunner";
+	compatible = "atmel,sama5d2-roadrunner", "atmel,sama5d27","atmel,sama5d2", "atmel,sama5";
+
+	bootargs = "mem=256M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait consoleblank=0";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		usb0: gadget@300000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+
+		usb1: ohci@400000 {
+			num-ports = <3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb_default>;
+			status = "okay";
+		};
+
+		usb2: ehci@500000 {
+			status = "okay";
+		};
+
+		/* MicroSD on Berta Board */
+
+		sdmmc1: sdio-host@b0000000 {
+			bus-width = <4>;
+			pinctrl-names = "default";
+			no-1-8-v;
+			non-removable;
+			pinctrl-0 = <&pinctrl_sdmmc1_default>;
+			status = "okay"; /* conflict with qspi0 */
+		};
+
+		/* sdio bus for Wifi module */
+
+		sdmmc0: sdio-host@a0000000 {
+			bus-width = <4>;
+			pinctrl-names = "default";
+			no-1-8-v;
+			non-removable;
+			pinctrl-0 = <&pinctrl_sdmmc0_default>;
+			status = "okay";
+
+			/*
+			 vmmc-supply = <&vcc_mmc1_reg>;
+			 vqmmc-supply = <&vcc_3v3_reg>;
+			*/	
+
+			brcmf: bcrmf@1 {
+				compatible = "brcm,bcm4329-fmac";
+				reg = <1>;
+				brcm,drive-strength = <6>;
+			};
+			
+			
+			 /*	
+			 slot@0 {
+				 reg = <0>;
+				 bus-width = <4>;
+			 };
+			 */
+
+			 /*wilc_sdio@0{
+				 compatible = "microchip,wilc1000", "microchip,wilc3000", "atmel,wilc_sdio";
+				 status = "okay";
+				 reg = <0>;
+				 bus-width = <4>;
+			 };*/
+ 
+
+			
+		};
+
+		apb {
+			spi0: spi@f8000000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_spi0_default>;
+				status = "disabled";
+			};
+
+			macb0: ethernet@f8008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+				phy-mode = "rmii";
+				status = "okay";
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+					interrupt-parent = <&pioA>;
+					interrupts = <73 IRQ_TYPE_LEVEL_LOW>;
+					/*interrupts = <PIN_PC9 IRQ_TYPE_LEVEL_LOW>;*/
+				};
+			};
+
+			tcb0: timer@f800c000 {
+				timer0: timer@0 {
+					compatible = "atmel,tcb-timer";
+					reg = <0>;
+				};
+
+				timer1: timer@1 {
+					compatible = "atmel,tcb-timer";
+					reg = <1>;
+				};
+			};
+
+			uart1: serial@f8020000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_default>;
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				status = "okay";
+			};
+
+			i2c0: i2c@f8028000 {
+				dmas = <0>, <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c0_default>;
+				i2c-sda-hold-time-ns = <350>;
+				status = "disabled";
+			};
+
+			pwm0: pwm@f802c000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_pwm0_pwm2_default>;
+				status = "disabled"; 
+			};
+
+			flx0: flexcom@f8034000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+				status = "disabled"; /* conflict with ISC_D2 & ISC_D3 data pins */
+
+				uart5: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&flx0_clk>;
+					clock-names = "usart";
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx0_default>;
+					atmel,fifo-size = <32>;
+					status = "disabled";
+				};
+			};
+
+			shdwc@f8048010 {
+				atmel,shdwc-debouncer = <976>;
+				atmel,wakeup-rtc-timer;
+
+				input@0 {
+					reg = <0>;
+					atmel,wakeup-type = "low";
+				};
+			};
+
+			watchdog@f8048040 {
+				status = "okay";
+			};
+
+			can0: can@f8054000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_can0_default>;
+				status = "disabled";
+			};
+
+			uart3: serial@fc008000 {
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart3_default>;
+				status = "disabled";
+			};
+
+			flx4: flexcom@fc018000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+				status = "disabled";
+
+				i2c2: i2c@600 {
+					compatible = "atmel,sama5d2-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <0>, <0>;
+					dma-names = "tx", "rx";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&flx4_clk>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx4_default>;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			i2c1: i2c@fc028000 {
+				dmas = <0>, <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1_default>;
+				status = "disabled";
+			};
+
+			vddin_3v3: fixed-regulator-vddin_3v3 {
+				compatible = "regulator-fixed";
+
+				regulator-name = "VDDIN_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				status = "okay";
+			};
+
+			vddana: fixed-regulator-vddana {
+				compatible = "regulator-fixed";
+
+				regulator-name = "VDDANA";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				vin-supply = <&vddin_3v3>;
+				status = "okay";
+			};
+
+			advref: fixed-regulator-advref {
+				compatible = "regulator-fixed";
+
+				regulator-name = "advref";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				vin-supply = <&vddana>;
+				status = "okay";
+			};
+
+			adc: adc@fc030000 {
+				vddana-supply = <&vddana>; 
+				vref-supply =  <&vddana>; 
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_adc_default>;
+				status = "okay";
+			};
+
+			pinctrl@fc038000 {
+				/*
+				 * There is no real pinmux for ADC, if the pin
+				 * is not requested by another peripheral then
+				 * the muxing is done when channel is enabled.
+				 * Requesting pins for ADC is GPIO is
+				 * encouraged to prevent conflicts and to
+				 * disable bias in order to be in the same
+				 * state when the pin is not muxed to the adc.
+				 */
+				pinctrl_adc_default: adc_default {
+					pinmux = <PIN_PD19__GPIO>,
+						<PIN_PD20__GPIO>,
+						<PIN_PD21__GPIO>,
+						<PIN_PD22__GPIO>,
+						<PIN_PD23__GPIO>,
+						<PIN_PD24__GPIO>,
+						<PIN_PD25__GPIO>,
+						<PIN_PD26__GPIO>,
+						<PIN_PD27__GPIO>,
+						<PIN_PD28__GPIO>,
+						<PIN_PD29__GPIO>,
+						<PIN_PD30__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_can0_default: can0_default {
+					pinmux = <PIN_PC10__CANTX0>,
+						 <PIN_PC11__CANRX0>;
+					bias-disable;
+				};
+
+				pinctrl_can1_default: can1_default {
+					pinmux = <PIN_PC26__CANTX1>,
+						 <PIN_PC27__CANRX1>;
+					bias-disable;
+				};
+
+				/*
+				 * The ADTRG pin can work on any edge type.
+				 * In here it's being pulled up, so need to
+				 * connect it to ground to get an edge e.g.
+				 * Trigger can be configured on falling, rise
+				 * or any edge, and the pull-up can be changed
+				 * to pull-down or left floating according to
+				 * needs.
+				 */
+				pinctrl_adtrg_default: adtrg_default {
+					pinmux = <PIN_PD31__ADTRG>;
+					bias-pull-up;
+				};
+
+				pinctrl_charger_chglev: charger_chglev {
+					pinmux = <PIN_PA12__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_charger_irq: charger_irq {
+					pinmux = <PIN_PB13__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_charger_lbo: charger_lbo {
+					pinmux = <PIN_PC8__GPIO>;
+					bias-pull-up;
+				};
+
+				pinctrl_classd_default: classd_default {
+					pinmux = <PIN_PB1__CLASSD_R0>,
+						 <PIN_PB2__CLASSD_R1>,
+						 <PIN_PB3__CLASSD_R2>,
+						 <PIN_PB4__CLASSD_R3>;
+					bias-pull-up;
+				};
+
+				pinctrl_flx0_default: flx0_default {
+					pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+						 <PIN_PB29__FLEXCOM0_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_flx4_default: flx4_default {
+					pinmux = <PIN_PD12__FLEXCOM4_IO0>,
+						 <PIN_PD13__FLEXCOM4_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_i2c0_default: i2c0_default {
+					pinmux = <PIN_PD21__TWD0>,
+						 <PIN_PD22__TWCK0>;
+					bias-disable;
+				};
+
+				pinctrl_i2c1_default: i2c1_default {
+					pinmux = <PIN_PD4__TWD1>,
+						 <PIN_PD5__TWCK1>;
+					bias-disable;
+				};
+
+				pinctrl_key_gpio_default: key_gpio_default {
+					pinmux = <PIN_PB9__GPIO>;
+					bias-pull-up;
+				};
+
+				pinctrl_macb0_default: macb0_default {
+					pinmux = <PIN_PB14__GTXCK>,
+						 <PIN_PB15__GTXEN>,
+						 <PIN_PB16__GRXDV>,
+						 <PIN_PB17__GRXER>,
+						 <PIN_PB18__GRX0>,
+						 <PIN_PB19__GRX1>,
+						 <PIN_PB20__GTX0>,
+						 <PIN_PB21__GTX1>,
+						 <PIN_PB22__GMDC>,
+						 <PIN_PB23__GMDIO>;
+					bias-disable;
+				};
+
+				pinctrl_macb0_phy_irq: macb0_phy_irq {
+					pinmux = <PIN_PC9__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_pdmic_default: pdmic_default {
+					pinmux = <PIN_PB26__PDMIC_DAT>,
+						<PIN_PB27__PDMIC_CLK>;
+					bias-disable;
+				};
+
+				pinctrl_sdmmc0_default: sdmmc0_default {
+					cmd_data {
+						pinmux = <PIN_PA1__SDMMC0_CMD>,
+							 <PIN_PA2__SDMMC0_DAT0>,
+							 <PIN_PA3__SDMMC0_DAT1>,
+							 <PIN_PA4__SDMMC0_DAT2>,
+							 <PIN_PA5__SDMMC0_DAT3>;
+						bias-disable;
+					};
+
+					ck_cd_rstn_vddsel {
+						pinmux = <PIN_PA0__SDMMC0_CK>;
+
+						bias-disable;
+					};
+				};
+
+				pinctrl_sdmmc1_default: sdmmc1_default {
+					cmd_data {
+						pinmux = <PIN_PA28__SDMMC1_CMD>,
+							 <PIN_PA18__SDMMC1_DAT0>,
+							 <PIN_PA19__SDMMC1_DAT1>,
+							 <PIN_PA20__SDMMC1_DAT2>,
+							 <PIN_PA21__SDMMC1_DAT3>;
+						bias-pull-up;
+					};
+
+					conf-ck_cd {
+						pinmux = <PIN_PA22__SDMMC1_CK>;
+						bias-disable;
+					};
+				};
+
+				pinctrl_spi0_default: spi0_default {
+					pinmux = <PIN_PA14__SPI0_SPCK>,
+						 <PIN_PA15__SPI0_MOSI>,
+						 <PIN_PA16__SPI0_MISO>,
+						 <PIN_PA17__SPI0_NPCS0>;
+					bias-disable;
+				};
+
+				pinctrl_uart1_default: uart1_default {
+					pinmux = <PIN_PD2__URXD1>,
+						 <PIN_PD3__UTXD1>;
+					bias-disable;
+				};
+
+				pinctrl_uart3_default: uart3_default {
+					pinmux = <PIN_PB11__URXD3>,
+						 <PIN_PB12__UTXD3>;
+					bias-disable;
+				};
+
+				pinctrl_usb_default: usb_default {
+					pinmux = <PIN_PB10__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_usba_vbus: usba_vbus {
+					pinmux = <PIN_PA31__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_pwm0_pwm2_default: pwm0_pwm2_default {
+					pinmux = <PIN_PB5__PWMH2>,
+						 <PIN_PB6__PWML2>;
+					bias-pull-up;
+				};
+			};
+
+			classd: classd@fc048000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_classd_default>;
+				atmel,pwm-type = "diff";
+				atmel,non-overlap-time = <10>;
+				status = "disabled";
+			};
+
+			can1: can@fc050000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_can1_default>;
+				status = "disabled";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/acme-roadrunner.dts b/arch/arm/boot/dts/acme-roadrunner.dts
new file mode 100644
index 000000000..400cdfab5
--- /dev/null
+++ b/arch/arm/boot/dts/acme-roadrunner.dts
@@ -0,0 +1,491 @@
+/*
+ * acme_roadrunner.dts - Device Tree file for Acme Systems
+ * RoadRunner SOM 
+ *
+ *  Copyright (C) 2015 Atmel,
+ *                2015 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *                2020 Sergio Tanzilli <tanzilli@acmesystems.it>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/gpio/gpio.h>
+
+
+
+/ {
+	model = "Acme Systems SAMA5D2 Roadrunner";
+	compatible = "atmel,sama5d2-roadrunner", "atmel,sama5d27","atmel,sama5d2", "atmel,sama5";
+
+	bootargs = "mem=256M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait consoleblank=0";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		usb0: gadget@300000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+
+		usb1: ohci@400000 {
+			num-ports = <3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb_default>;
+			status = "okay";
+		};
+
+		usb2: ehci@500000 {
+			status = "okay";
+		};
+
+		sdmmc1: sdio-host@b0000000 {
+			bus-width = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc1_default>;
+			non-removable;
+			status = "okay"; /* conflict with qspi0 */
+		};
+
+		apb {
+			spi0: spi@f8000000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_spi0_default>;
+				status = "disabled";
+			};
+
+			macb0: ethernet@f8008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+				phy-mode = "rmii";
+				status = "okay";
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+					interrupt-parent = <&pioA>;
+					interrupts = <73 IRQ_TYPE_LEVEL_LOW>;
+					/*interrupts = <PIN_PC9 IRQ_TYPE_LEVEL_LOW>;*/
+				};
+			};
+
+			tcb0: timer@f800c000 {
+				timer0: timer@0 {
+					compatible = "atmel,tcb-timer";
+					reg = <0>;
+				};
+
+				timer1: timer@1 {
+					compatible = "atmel,tcb-timer";
+					reg = <1>;
+				};
+			};
+
+			uart1: serial@f8020000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_default>;
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				status = "okay";
+			};
+
+			i2c0: i2c@f8028000 {
+				dmas = <0>, <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c0_default>;
+				i2c-sda-hold-time-ns = <350>;
+				status = "disabled";
+			};
+
+			pwm0: pwm@f802c000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_pwm0_pwm2_default>;
+				status = "disabled"; 
+			};
+
+			flx0: flexcom@f8034000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+				status = "disabled"; /* conflict with ISC_D2 & ISC_D3 data pins */
+
+				uart5: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&flx0_clk>;
+					clock-names = "usart";
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx0_default>;
+					atmel,fifo-size = <32>;
+					status = "disabled";
+				};
+			};
+
+			shdwc@f8048010 {
+				atmel,shdwc-debouncer = <976>;
+				atmel,wakeup-rtc-timer;
+
+				input@0 {
+					reg = <0>;
+					atmel,wakeup-type = "low";
+				};
+			};
+
+			watchdog@f8048040 {
+				status = "okay";
+			};
+
+			can0: can@f8054000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_can0_default>;
+				status = "disabled";
+			};
+
+			uart3: serial@fc008000 {
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart3_default>;
+				status = "disabled";
+			};
+
+			flx4: flexcom@fc018000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+				status = "disabled";
+
+				i2c2: i2c@600 {
+					compatible = "atmel,sama5d2-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <0>, <0>;
+					dma-names = "tx", "rx";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&flx4_clk>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx4_default>;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			i2c1: i2c@fc028000 {
+				dmas = <0>, <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1_default>;
+				status = "disabled";
+			};
+
+			vddin_3v3: fixed-regulator-vddin_3v3 {
+				compatible = "regulator-fixed";
+
+				regulator-name = "VDDIN_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				status = "okay";
+			};
+
+			vddana: fixed-regulator-vddana {
+				compatible = "regulator-fixed";
+
+				regulator-name = "VDDANA";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				vin-supply = <&vddin_3v3>;
+				status = "okay";
+			};
+
+			advref: fixed-regulator-advref {
+				compatible = "regulator-fixed";
+
+				regulator-name = "advref";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				vin-supply = <&vddana>;
+				status = "okay";
+			};
+
+			adc: adc@fc030000 {
+				vddana-supply = <&vddana>; 
+				vref-supply =  <&vddana>; 
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_adc_default>;
+				status = "okay";
+			};
+
+			pinctrl@fc038000 {
+				/*
+				 * There is no real pinmux for ADC, if the pin
+				 * is not requested by another peripheral then
+				 * the muxing is done when channel is enabled.
+				 * Requesting pins for ADC is GPIO is
+				 * encouraged to prevent conflicts and to
+				 * disable bias in order to be in the same
+				 * state when the pin is not muxed to the adc.
+				 */
+				pinctrl_adc_default: adc_default {
+					pinmux = <PIN_PD19__GPIO>,
+						<PIN_PD20__GPIO>,
+						<PIN_PD21__GPIO>,
+						<PIN_PD22__GPIO>,
+						<PIN_PD23__GPIO>,
+						<PIN_PD24__GPIO>,
+						<PIN_PD25__GPIO>,
+						<PIN_PD26__GPIO>,
+						<PIN_PD27__GPIO>,
+						<PIN_PD28__GPIO>,
+						<PIN_PD29__GPIO>,
+						<PIN_PD30__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_can0_default: can0_default {
+					pinmux = <PIN_PC10__CANTX0>,
+						 <PIN_PC11__CANRX0>;
+					bias-disable;
+				};
+
+				pinctrl_can1_default: can1_default {
+					pinmux = <PIN_PC26__CANTX1>,
+						 <PIN_PC27__CANRX1>;
+					bias-disable;
+				};
+
+				/*
+				 * The ADTRG pin can work on any edge type.
+				 * In here it's being pulled up, so need to
+				 * connect it to ground to get an edge e.g.
+				 * Trigger can be configured on falling, rise
+				 * or any edge, and the pull-up can be changed
+				 * to pull-down or left floating according to
+				 * needs.
+				 */
+				pinctrl_adtrg_default: adtrg_default {
+					pinmux = <PIN_PD31__ADTRG>;
+					bias-pull-up;
+				};
+
+				pinctrl_charger_chglev: charger_chglev {
+					pinmux = <PIN_PA12__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_charger_irq: charger_irq {
+					pinmux = <PIN_PB13__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_charger_lbo: charger_lbo {
+					pinmux = <PIN_PC8__GPIO>;
+					bias-pull-up;
+				};
+
+				pinctrl_classd_default: classd_default {
+					pinmux = <PIN_PB1__CLASSD_R0>,
+						 <PIN_PB2__CLASSD_R1>,
+						 <PIN_PB3__CLASSD_R2>,
+						 <PIN_PB4__CLASSD_R3>;
+					bias-pull-up;
+				};
+
+				pinctrl_flx0_default: flx0_default {
+					pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+						 <PIN_PB29__FLEXCOM0_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_flx4_default: flx4_default {
+					pinmux = <PIN_PD12__FLEXCOM4_IO0>,
+						 <PIN_PD13__FLEXCOM4_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_i2c0_default: i2c0_default {
+					pinmux = <PIN_PD21__TWD0>,
+						 <PIN_PD22__TWCK0>;
+					bias-disable;
+				};
+
+				pinctrl_i2c1_default: i2c1_default {
+					pinmux = <PIN_PD4__TWD1>,
+						 <PIN_PD5__TWCK1>;
+					bias-disable;
+				};
+
+				pinctrl_key_gpio_default: key_gpio_default {
+					pinmux = <PIN_PB9__GPIO>;
+					bias-pull-up;
+				};
+
+				pinctrl_macb0_default: macb0_default {
+					pinmux = <PIN_PB14__GTXCK>,
+						 <PIN_PB15__GTXEN>,
+						 <PIN_PB16__GRXDV>,
+						 <PIN_PB17__GRXER>,
+						 <PIN_PB18__GRX0>,
+						 <PIN_PB19__GRX1>,
+						 <PIN_PB20__GTX0>,
+						 <PIN_PB21__GTX1>,
+						 <PIN_PB22__GMDC>,
+						 <PIN_PB23__GMDIO>;
+					bias-disable;
+				};
+
+				pinctrl_macb0_phy_irq: macb0_phy_irq {
+					pinmux = <PIN_PC9__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_pdmic_default: pdmic_default {
+					pinmux = <PIN_PB26__PDMIC_DAT>,
+						<PIN_PB27__PDMIC_CLK>;
+					bias-disable;
+				};
+
+				pinctrl_sdmmc0_default: sdmmc0_default {
+					cmd_data {
+						pinmux = <PIN_PA1__SDMMC0_CMD>,
+							 <PIN_PA2__SDMMC0_DAT0>,
+							 <PIN_PA3__SDMMC0_DAT1>,
+							 <PIN_PA4__SDMMC0_DAT2>,
+							 <PIN_PA5__SDMMC0_DAT3>,
+							 <PIN_PA6__SDMMC0_DAT4>,
+							 <PIN_PA7__SDMMC0_DAT5>,
+							 <PIN_PA8__SDMMC0_DAT6>,
+							 <PIN_PA9__SDMMC0_DAT7>;
+						bias-disable;
+					};
+
+					ck_cd_rstn_vddsel {
+						pinmux = <PIN_PA0__SDMMC0_CK>,
+							 <PIN_PA10__SDMMC0_RSTN>,
+							 <PIN_PA11__SDMMC0_VDDSEL>,
+							 <PIN_PA13__SDMMC0_CD>;
+						bias-disable;
+					};
+				};
+
+				pinctrl_sdmmc1_default: sdmmc1_default {
+					cmd_data {
+						pinmux = <PIN_PA28__SDMMC1_CMD>,
+							 <PIN_PA18__SDMMC1_DAT0>,
+							 <PIN_PA19__SDMMC1_DAT1>,
+							 <PIN_PA20__SDMMC1_DAT2>,
+							 <PIN_PA21__SDMMC1_DAT3>;
+						bias-pull-up;
+					};
+
+					conf-ck_cd {
+						pinmux = <PIN_PA22__SDMMC1_CK>;
+						bias-disable;
+					};
+				};
+
+				pinctrl_spi0_default: spi0_default {
+					pinmux = <PIN_PA14__SPI0_SPCK>,
+						 <PIN_PA15__SPI0_MOSI>,
+						 <PIN_PA16__SPI0_MISO>,
+						 <PIN_PA17__SPI0_NPCS0>;
+					bias-disable;
+				};
+
+				pinctrl_uart1_default: uart1_default {
+					pinmux = <PIN_PD2__URXD1>,
+						 <PIN_PD3__UTXD1>;
+					bias-disable;
+				};
+
+				pinctrl_uart3_default: uart3_default {
+					pinmux = <PIN_PB11__URXD3>,
+						 <PIN_PB12__UTXD3>;
+					bias-disable;
+				};
+
+				pinctrl_usb_default: usb_default {
+					pinmux = <PIN_PB10__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_usba_vbus: usba_vbus {
+					pinmux = <PIN_PA31__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_pwm0_pwm2_default: pwm0_pwm2_default {
+					pinmux = <PIN_PB5__PWMH2>,
+						 <PIN_PB6__PWML2>;
+					bias-pull-up;
+				};
+			};
+
+			classd: classd@fc048000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_classd_default>;
+				atmel,pwm-type = "diff";
+				atmel,non-overlap-time = <10>;
+				status = "disabled";
+			};
+
+			can1: can@fc050000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_can1_default>;
+				status = "disabled";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/acme-xterm-01.dts b/arch/arm/boot/dts/acme-xterm-01.dts
new file mode 100644
index 000000000..924e449e4
--- /dev/null
+++ b/arch/arm/boot/dts/acme-xterm-01.dts
@@ -0,0 +1,118 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Arietta G25 and XTerm-01
+ * https://www.acmesystems.it/XTERM-01
+ */
+/dts-v1/;
+#include "at91sam9g25.dtsi"
+/ {
+	model = "Acme Systems Arietta G25";
+	compatible = "acme,ariettag25", "atmel,at91sam9x5", "atmel,at91sam9";
+
+	aliases {
+		serial0 = &dbgu;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0x20000000 0x8000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			mmc0: mmc@f0008000 {
+				pinctrl-0 = <
+				  &pinctrl_mmc0_slot0_clk_cmd_dat0
+				  &pinctrl_mmc0_slot0_dat1_3>;
+				status = "okay";
+
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+				};
+			};
+
+			tcb0: timer@f8008000 {
+				timer@0 {
+					compatible = "atmel,tcb-timer";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-timer";
+					reg = <1>;
+				};
+			};
+
+			usb2: gadget@f803c000 {
+				status = "okay";
+			};
+
+			dbgu: serial@fffff200 {
+				status = "okay";
+			};
+
+			rtc@fffffeb0 {
+				status = "okay";
+			};
+			
+			spi1: spi@f0004000 {
+				status = "okay";
+				cs-gpios = <&pioA 8 0>;
+
+				device@0 {
+					rotate = <270>;
+					bgr;
+					fps = <30>;
+					compatible = "ilitek,ili9341";
+					spi-max-frequency = <50000000>;   
+					reg = <0>;
+					regwidth = <8>;
+					buswidth = <8>;
+					verbose = <3>;
+					reset-gpios = <&pioC 3 0>; /* PC3 - J4.33 */
+					dc-gpios = <&pioC 4 0>;    /* PC4 - J4.31 */
+				};
+			};
+			
+			adc0: adc@f804c000 {
+				compatible = "atmel,at91sam9x5-adc";
+				atmel,adc-clock-rate = <1000000>;
+				atmel,adc-ts-wires = <4>;
+				atmel,adc-ts-pressure-threshold = <10000>;
+				status = "okay";
+			};
+		};
+
+		usb0: ohci@600000 {
+			status = "okay";
+			num-ports = <3>;
+		};
+
+		usb1: ehci@700000 {
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		arietta_led {
+			label = "arietta_led";
+			gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
diff --git a/arch/arm/configs/acme-acqua_defconfig b/arch/arm/configs/acme-acqua_defconfig
new file mode 100644
index 000000000..db5042d6f
--- /dev/null
+++ b/arch/arm/configs/acme-acqua_defconfig
@@ -0,0 +1,225 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_ARCH_AT91=y
+CONFIG_SOC_SAMA5D2=y
+CONFIG_SOC_SAMA5D3=y
+CONFIG_SOC_SAMA5D4=y
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_CMDLINE="console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
+CONFIG_KEXEC=y
+CONFIG_VFP=y
+CONFIG_NEON=y
+CONFIG_KERNEL_MODE_NEON=y
+CONFIG_PM_DEBUG=y
+CONFIG_PM_ADVANCED_DEBUG=y
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_CAN=y
+CONFIG_CAN_AT91=y
+CONFIG_CAN_M_CAN=y
+CONFIG_CFG80211=y
+CONFIG_MAC80211=y
+CONFIG_MAC80211_LEDS=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_M25P80=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_SPI_NOR=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_GLUEBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_ATMEL_TCLIB=y
+CONFIG_ATMEL_SSC=y
+CONFIG_EEPROM_AT24=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+CONFIG_MACB=y
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MICROCHIP is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_MICREL_PHY=y
+# CONFIG_WLAN_VENDOR_ADMTEK is not set
+# CONFIG_WLAN_VENDOR_ATH is not set
+# CONFIG_WLAN_VENDOR_CISCO is not set
+# CONFIG_WLAN_VENDOR_INTEL is not set
+# CONFIG_WLAN_VENDOR_INTERSIL is not set
+# CONFIG_WLAN_VENDOR_MARVELL is not set
+# CONFIG_WLAN_VENDOR_MEDIATEK is not set
+# CONFIG_WLAN_VENDOR_RALINK is not set
+# CONFIG_WLAN_VENDOR_REALTEK is not set
+# CONFIG_WLAN_VENDOR_RSI is not set
+# CONFIG_WLAN_VENDOR_ST is not set
+# CONFIG_WLAN_VENDOR_TI is not set
+# CONFIG_WLAN_VENDOR_ZYDAS is not set
+# CONFIG_WLAN_VENDOR_QUANTENNA is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_QT1070=y
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ATMEL_MXT=y
+# CONFIG_SERIO is not set
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_AT91=y
+CONFIG_I2C_GPIO=y
+CONFIG_SPI=y
+CONFIG_SPI_ATMEL=y
+CONFIG_SPI_GPIO=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_SUPPLY=y
+CONFIG_SENSORS_JC42=y
+CONFIG_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
+CONFIG_SAMA5D4_WATCHDOG=y
+CONFIG_MFD_ACT8945A=y
+CONFIG_MFD_ATMEL_FLEXCOM=y
+CONFIG_MFD_ATMEL_HLCDC=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_PWM=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_MEDIA_CAMERA_SUPPORT=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_SOC_CAMERA=y
+CONFIG_VIDEO_ATMEL_ISI=y
+CONFIG_DRM=y
+CONFIG_DRM_ATMEL_HLCDC=y
+CONFIG_DRM_PANEL_SIMPLE=y
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_SOC=y
+CONFIG_SND_ATMEL_SOC=y
+CONFIG_SND_ATMEL_SOC_PDMIC=y
+# CONFIG_HID_GENERIC is not set
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_ACM=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_FTDI_SIO=y
+CONFIG_USB_SERIAL_PL2303=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_ATMEL_USBA=y
+CONFIG_USB_G_SERIAL=y
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_OF_AT91=y
+CONFIG_MMC_ATMELMCI=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_PWM=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_AT91RM9200=y
+CONFIG_DMADEVICES=y
+CONFIG_AT_HDMAC=y
+CONFIG_AT_XDMAC=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_AT91_ADC=y
+CONFIG_AT91_SAMA5D2_ADC=y
+CONFIG_DPOT_DAC=y
+CONFIG_PWM=y
+CONFIG_PWM_ATMEL=y
+CONFIG_PWM_ATMEL_HLCDC_PWM=y
+CONFIG_PWM_ATMEL_TCB=y
+CONFIG_EXT4_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_ECHAINIV=y
+CONFIG_CRYPTO_USER_API_HASH=y
+CONFIG_CRYPTO_USER_API_SKCIPHER=y
+CONFIG_CRYPTO_DEV_ATMEL_AES=y
+CONFIG_CRYPTO_DEV_ATMEL_TDES=y
+CONFIG_CRYPTO_DEV_ATMEL_SHA=y
+CONFIG_CRC_CCITT=y
+CONFIG_CRC_ITU_T=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_DEBUG_MEMORY_INIT=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/acme-aria_defconfig b/arch/arm/configs/acme-aria_defconfig
new file mode 100644
index 000000000..c32128040
--- /dev/null
+++ b/arch/arm/configs/acme-aria_defconfig
@@ -0,0 +1,211 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_ARCH_MULTI_V4T=y
+CONFIG_ARCH_MULTI_V5=y
+# CONFIG_ARCH_MULTI_V7 is not set
+CONFIG_ARCH_AT91=y
+CONFIG_SOC_AT91RM9200=y
+CONFIG_SOC_AT91SAM9=y
+CONFIG_AEABI=y
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_ARM_ATAG_DTB_COMPAT=y
+CONFIG_CMDLINE="console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
+CONFIG_KEXEC=y
+CONFIG_STRICT_KERNEL_RWX=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_CFG80211=y
+CONFIG_MAC80211=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_DATAFLASH=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_GLUEBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_ATMEL_TCLIB=y
+CONFIG_ATMEL_SSC=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+CONFIG_MACB=y
+CONFIG_DM9000=y
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+CONFIG_DAVICOM_PHY=y
+CONFIG_MICREL_PHY=y
+# CONFIG_WLAN_VENDOR_ADMTEK is not set
+# CONFIG_WLAN_VENDOR_ATH is not set
+# CONFIG_WLAN_VENDOR_ATMEL is not set
+# CONFIG_WLAN_VENDOR_BROADCOM is not set
+# CONFIG_WLAN_VENDOR_CISCO is not set
+# CONFIG_WLAN_VENDOR_INTEL is not set
+# CONFIG_WLAN_VENDOR_INTERSIL is not set
+# CONFIG_WLAN_VENDOR_MARVELL is not set
+# CONFIG_WLAN_VENDOR_MEDIATEK is not set
+CONFIG_RT2X00=y
+CONFIG_RT2800USB=y
+CONFIG_RT2800USB_RT53XX=y
+# CONFIG_WLAN_VENDOR_REALTEK is not set
+# CONFIG_WLAN_VENDOR_RSI is not set
+# CONFIG_WLAN_VENDOR_ST is not set
+# CONFIG_WLAN_VENDOR_TI is not set
+# CONFIG_WLAN_VENDOR_ZYDAS is not set
+# CONFIG_WLAN_VENDOR_QUANTENNA is not set
+CONFIG_INPUT_POLLDEV=y
+CONFIG_INPUT_JOYDEV=y
+CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_QT1070=y
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ADS7846=y
+# CONFIG_SERIO is not set
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C_AT91=y
+CONFIG_I2C_GPIO=y
+CONFIG_SPI=y
+CONFIG_SPI_ATMEL=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_SUPPLY=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
+CONFIG_MFD_ATMEL_HLCDC=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_MEDIA_CAMERA_SUPPORT=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_SOC_CAMERA=y
+CONFIG_VIDEO_ATMEL_ISI=y
+CONFIG_DRM=y
+CONFIG_DRM_ATMEL_HLCDC=y
+CONFIG_DRM_PANEL_SIMPLE=y
+CONFIG_FB_ATMEL=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+CONFIG_BACKLIGHT_ATMEL_LCDC=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_ACM=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_FTDI_SIO=y
+CONFIG_USB_SERIAL_PL2303=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_AT91=y
+CONFIG_USB_ATMEL_USBA=y
+CONFIG_USB_G_SERIAL=y
+CONFIG_MMC=y
+CONFIG_MMC_ATMELMCI=y
+CONFIG_MMC_SPI=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_PWM=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_RV3029C2=y
+CONFIG_RTC_DRV_AT91RM9200=y
+CONFIG_RTC_DRV_AT91SAM9=y
+CONFIG_DMADEVICES=y
+CONFIG_AT_HDMAC=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_AT91_ADC=y
+CONFIG_PWM=y
+CONFIG_PWM_ATMEL=y
+CONFIG_PWM_ATMEL_HLCDC_PWM=y
+CONFIG_PWM_ATMEL_TCB=y
+CONFIG_EXT4_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+# CONFIG_CRYPTO_ECHAINIV is not set
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_USER_API_HASH=y
+CONFIG_CRYPTO_USER_API_SKCIPHER=y
+# CONFIG_CRYPTO_HW is not set
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_ACORN_8x8=y
+CONFIG_FONT_MINI_4x6=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/acme-arietta_defconfig b/arch/arm/configs/acme-arietta_defconfig
new file mode 100644
index 000000000..896a6b0b0
--- /dev/null
+++ b/arch/arm/configs/acme-arietta_defconfig
@@ -0,0 +1,214 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_ARCH_MULTI_V4T=y
+CONFIG_ARCH_MULTI_V5=y
+# CONFIG_ARCH_MULTI_V7 is not set
+CONFIG_ARCH_AT91=y
+CONFIG_SOC_AT91RM9200=y
+CONFIG_SOC_AT91SAM9=y
+CONFIG_AEABI=y
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_ARM_ATAG_DTB_COMPAT=y
+CONFIG_CMDLINE="console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
+CONFIG_KEXEC=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_CFG80211=y
+CONFIG_MAC80211=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_DATAFLASH=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_GLUEBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_ATMEL_TCLIB=y
+CONFIG_ATMEL_SSC=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+CONFIG_MACB=y
+CONFIG_DM9000=y
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+CONFIG_DAVICOM_PHY=y
+CONFIG_MICREL_PHY=y
+# CONFIG_WLAN_VENDOR_ADMTEK is not set
+# CONFIG_WLAN_VENDOR_ATH is not set
+# CONFIG_WLAN_VENDOR_ATMEL is not set
+# CONFIG_WLAN_VENDOR_BROADCOM is not set
+# CONFIG_WLAN_VENDOR_CISCO is not set
+# CONFIG_WLAN_VENDOR_INTEL is not set
+# CONFIG_WLAN_VENDOR_INTERSIL is not set
+# CONFIG_WLAN_VENDOR_MARVELL is not set
+# CONFIG_WLAN_VENDOR_MEDIATEK is not set
+CONFIG_RT2X00=y
+CONFIG_RT2800USB=y
+CONFIG_RT2800USB_RT53XX=y
+# CONFIG_WLAN_VENDOR_REALTEK is not set
+# CONFIG_WLAN_VENDOR_RSI is not set
+# CONFIG_WLAN_VENDOR_ST is not set
+# CONFIG_WLAN_VENDOR_TI is not set
+# CONFIG_WLAN_VENDOR_ZYDAS is not set
+# CONFIG_WLAN_VENDOR_QUANTENNA is not set
+CONFIG_INPUT_POLLDEV=y
+CONFIG_INPUT_JOYDEV=y
+CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_QT1070=y
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ADS7846=y
+# CONFIG_SERIO is not set
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C_AT91=y
+CONFIG_I2C_GPIO=y
+CONFIG_SPI=y
+CONFIG_SPI_ATMEL=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_SUPPLY=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
+CONFIG_MFD_ATMEL_HLCDC=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_MEDIA_CAMERA_SUPPORT=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_SOC_CAMERA=y
+CONFIG_VIDEO_ATMEL_ISI=y
+CONFIG_DRM=y
+CONFIG_DRM_ATMEL_HLCDC=y
+CONFIG_DRM_PANEL_SIMPLE=y
+CONFIG_FB_ATMEL=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+CONFIG_BACKLIGHT_ATMEL_LCDC=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_ACM=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_FTDI_SIO=y
+CONFIG_USB_SERIAL_PL2303=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_AT91=y
+CONFIG_USB_ATMEL_USBA=y
+CONFIG_USB_G_SERIAL=y
+CONFIG_MMC=y
+CONFIG_MMC_ATMELMCI=y
+CONFIG_MMC_SPI=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_PWM=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_RV3029C2=y
+CONFIG_RTC_DRV_AT91RM9200=y
+CONFIG_RTC_DRV_AT91SAM9=y
+CONFIG_DMADEVICES=y
+CONFIG_AT_HDMAC=y
+CONFIG_STAGING=y
+CONFIG_FB_TFT=y
+CONFIG_FB_TFT_ILI9341=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_AT91_ADC=y
+CONFIG_PWM=y
+CONFIG_PWM_ATMEL=y
+CONFIG_PWM_ATMEL_HLCDC_PWM=y
+CONFIG_PWM_ATMEL_TCB=y
+CONFIG_EXT4_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_AUTOFS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+# CONFIG_CRYPTO_ECHAINIV is not set
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_USER_API_HASH=y
+CONFIG_CRYPTO_USER_API_SKCIPHER=y
+# CONFIG_CRYPTO_HW is not set
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_ACORN_8x8=y
+CONFIG_FONT_MINI_4x6=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/acme-roadrunner-isc_defconfig b/arch/arm/configs/acme-roadrunner-isc_defconfig
new file mode 100644
index 000000000..a44a52366
--- /dev/null
+++ b/arch/arm/configs/acme-roadrunner-isc_defconfig
@@ -0,0 +1,231 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_ARCH_AT91=y
+CONFIG_SOC_SAMA5D2=y
+CONFIG_SOC_SAMA5D3=y
+CONFIG_SOC_SAMA5D4=y
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_CMDLINE="mem=256M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait consoleblank=0"
+CONFIG_KEXEC=y
+CONFIG_VFP=y
+CONFIG_NEON=y
+CONFIG_KERNEL_MODE_NEON=y
+CONFIG_PM_DEBUG=y
+CONFIG_PM_ADVANCED_DEBUG=y
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_CAN=y
+CONFIG_CAN_AT91=y
+CONFIG_CAN_M_CAN=y
+CONFIG_CFG80211=y
+CONFIG_MAC80211=y
+CONFIG_MAC80211_LEDS=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_M25P80=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_SPI_NOR=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_GLUEBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_ATMEL_TCLIB=y
+CONFIG_ATMEL_SSC=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+CONFIG_MACB=y
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MICROCHIP is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_MICREL_PHY=y
+# CONFIG_WLAN_VENDOR_ADMTEK is not set
+# CONFIG_WLAN_VENDOR_ATH is not set
+# CONFIG_WLAN_VENDOR_ATMEL is not set
+# CONFIG_WLAN_VENDOR_BROADCOM is not set
+# CONFIG_WLAN_VENDOR_CISCO is not set
+# CONFIG_WLAN_VENDOR_INTEL is not set
+# CONFIG_WLAN_VENDOR_INTERSIL is not set
+# CONFIG_WLAN_VENDOR_MARVELL is not set
+# CONFIG_WLAN_VENDOR_MEDIATEK is not set
+# CONFIG_WLAN_VENDOR_RALINK is not set
+# CONFIG_WLAN_VENDOR_REALTEK is not set
+# CONFIG_WLAN_VENDOR_RSI is not set
+# CONFIG_WLAN_VENDOR_ST is not set
+# CONFIG_WLAN_VENDOR_TI is not set
+# CONFIG_WLAN_VENDOR_ZYDAS is not set
+# CONFIG_WLAN_VENDOR_QUANTENNA is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_QT1070=y
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ATMEL_MXT=y
+# CONFIG_SERIO is not set
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_AT91=y
+CONFIG_I2C_GPIO=y
+CONFIG_SPI=y
+CONFIG_SPI_ATMEL=y
+CONFIG_SPI_GPIO=y
+CONFIG_SPI_SPIDEV=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_POWER_RESET=y
+CONFIG_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
+CONFIG_SAMA5D4_WATCHDOG=y
+CONFIG_SSB=y
+CONFIG_BCMA=y
+CONFIG_MFD_ACT8945A=y
+CONFIG_MFD_ATMEL_FLEXCOM=y
+CONFIG_MFD_ATMEL_HLCDC=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_MEDIA_CAMERA_SUPPORT=y
+CONFIG_MEDIA_CONTROLLER=y
+CONFIG_VIDEO_V4L2_SUBDEV_API=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_VIDEO_ATMEL_ISC=y
+CONFIG_VIDEO_ATMEL_ISI=y
+# CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set
+CONFIG_VIDEO_OV5640=y
+CONFIG_VIDEO_OV7670=y
+CONFIG_DRM=y
+CONFIG_DRM_ATMEL_HLCDC=y
+CONFIG_DRM_PANEL_SIMPLE=y
+CONFIG_LCD_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+# CONFIG_HID_GENERIC is not set
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_ACM=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_FTDI_SIO=y
+CONFIG_USB_SERIAL_PL2303=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_ATMEL_USBA=y
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_OF_AT91=y
+CONFIG_MMC_ATMELMCI=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_PWM=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_AT91RM9200=y
+CONFIG_DMADEVICES=y
+CONFIG_AT_HDMAC=y
+CONFIG_AT_XDMAC=y
+CONFIG_STAGING=y
+CONFIG_FB_TFT=y
+CONFIG_FB_TFT_ILI9341=y
+CONFIG_WILC1000_SDIO=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_AT91_ADC=y
+CONFIG_AT91_SAMA5D2_ADC=y
+CONFIG_ENVELOPE_DETECTOR=y
+CONFIG_PWM=y
+CONFIG_PWM_ATMEL=y
+CONFIG_PWM_ATMEL_HLCDC_PWM=y
+CONFIG_PWM_ATMEL_TCB=y
+CONFIG_EXT4_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_ECHAINIV=y
+CONFIG_CRYPTO_USER_API_HASH=y
+CONFIG_CRYPTO_USER_API_SKCIPHER=y
+CONFIG_CRYPTO_DEV_ATMEL_AES=y
+CONFIG_CRYPTO_DEV_ATMEL_TDES=y
+CONFIG_CRYPTO_DEV_ATMEL_SHA=y
+CONFIG_CRC_CCITT=y
+CONFIG_CRC_ITU_T=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_DEBUG_MEMORY_INIT=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/acme-roadrunner_defconfig b/arch/arm/configs/acme-roadrunner_defconfig
new file mode 100644
index 000000000..04b31b0d0
--- /dev/null
+++ b/arch/arm/configs/acme-roadrunner_defconfig
@@ -0,0 +1,235 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_ARCH_AT91=y
+CONFIG_SOC_SAMA5D2=y
+CONFIG_SOC_SAMA5D3=y
+CONFIG_SOC_SAMA5D4=y
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_CMDLINE="mem=256M console=ttyS0,115200 root=/dev/mmcblk1p2 rootfstype=ext4 rw rootwait consoleblank=0"
+CONFIG_KEXEC=y
+CONFIG_VFP=y
+CONFIG_NEON=y
+CONFIG_KERNEL_MODE_NEON=y
+CONFIG_PM_DEBUG=y
+CONFIG_PM_ADVANCED_DEBUG=y
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_CAN=y
+CONFIG_CAN_AT91=y
+CONFIG_CAN_M_CAN=y
+CONFIG_CFG80211=y
+CONFIG_MAC80211=y
+CONFIG_MAC80211_LEDS=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_M25P80=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_SPI_NOR=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_GLUEBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_ATMEL_TCLIB=y
+CONFIG_ATMEL_SSC=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+CONFIG_MACB=y
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MICROCHIP is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_MICREL_PHY=y
+# CONFIG_WLAN_VENDOR_ADMTEK is not set
+# CONFIG_WLAN_VENDOR_ATH is not set
+# CONFIG_WLAN_VENDOR_ATMEL is not set
+# CONFIG_WLAN_VENDOR_BROADCOM is not set
+# CONFIG_WLAN_VENDOR_CISCO is not set
+# CONFIG_WLAN_VENDOR_INTEL is not set
+# CONFIG_WLAN_VENDOR_INTERSIL is not set
+# CONFIG_WLAN_VENDOR_MARVELL is not set
+# CONFIG_WLAN_VENDOR_MEDIATEK is not set
+# CONFIG_WLAN_VENDOR_RALINK is not set
+# CONFIG_WLAN_VENDOR_REALTEK is not set
+# CONFIG_WLAN_VENDOR_RSI is not set
+# CONFIG_WLAN_VENDOR_ST is not set
+# CONFIG_WLAN_VENDOR_TI is not set
+# CONFIG_WLAN_VENDOR_ZYDAS is not set
+# CONFIG_WLAN_VENDOR_QUANTENNA is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_QT1070=y
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ATMEL_MXT=y
+# CONFIG_SERIO is not set
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_AT91=y
+CONFIG_I2C_GPIO=y
+CONFIG_SPI=y
+CONFIG_SPI_ATMEL=y
+CONFIG_SPI_GPIO=y
+CONFIG_SPI_SPIDEV=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_POWER_RESET=y
+CONFIG_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
+CONFIG_SAMA5D4_WATCHDOG=y
+CONFIG_SSB=y
+CONFIG_BCMA=y
+CONFIG_MFD_ACT8945A=y
+CONFIG_MFD_ATMEL_FLEXCOM=y
+CONFIG_MFD_ATMEL_HLCDC=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_MEDIA_CAMERA_SUPPORT=y
+CONFIG_MEDIA_CONTROLLER=y
+CONFIG_VIDEO_V4L2_SUBDEV_API=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_VIDEO_ATMEL_ISC=y
+CONFIG_VIDEO_ATMEL_ISI=y
+# CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set
+CONFIG_VIDEO_OV5640=y
+CONFIG_VIDEO_OV7670=y
+CONFIG_DRM=y
+CONFIG_DRM_ATMEL_HLCDC=y
+CONFIG_DRM_PANEL_SIMPLE=y
+CONFIG_LCD_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_SOC=y
+CONFIG_SND_ATMEL_SOC=y
+CONFIG_SND_ATMEL_SOC_CLASSD=y
+CONFIG_SND_ATMEL_SOC_PDMIC=y
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_ACM=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_FTDI_SIO=y
+CONFIG_USB_SERIAL_PL2303=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_ATMEL_USBA=y
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_OF_AT91=y
+CONFIG_MMC_ATMELMCI=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_PWM=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_AT91RM9200=y
+CONFIG_DMADEVICES=y
+CONFIG_AT_HDMAC=y
+CONFIG_AT_XDMAC=y
+CONFIG_STAGING=y
+CONFIG_FB_TFT=y
+CONFIG_FB_TFT_SSD1351=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_AT91_ADC=y
+CONFIG_AT91_SAMA5D2_ADC=y
+CONFIG_ENVELOPE_DETECTOR=y
+CONFIG_PWM=y
+CONFIG_PWM_ATMEL=y
+CONFIG_PWM_ATMEL_HLCDC_PWM=y
+CONFIG_PWM_ATMEL_TCB=y
+CONFIG_EXT4_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_ECHAINIV=y
+CONFIG_CRYPTO_USER_API_HASH=y
+CONFIG_CRYPTO_USER_API_SKCIPHER=y
+CONFIG_CRYPTO_DEV_ATMEL_AES=y
+CONFIG_CRYPTO_DEV_ATMEL_TDES=y
+CONFIG_CRYPTO_DEV_ATMEL_SHA=y
+CONFIG_CRC_CCITT=y
+CONFIG_CRC_ITU_T=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_DEBUG_MEMORY_INIT=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/acme-xterm-01_defconfig b/arch/arm/configs/acme-xterm-01_defconfig
new file mode 100644
index 000000000..870c5bfbb
--- /dev/null
+++ b/arch/arm/configs/acme-xterm-01_defconfig
@@ -0,0 +1,211 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_ARCH_MULTI_V4T=y
+CONFIG_ARCH_MULTI_V5=y
+# CONFIG_ARCH_MULTI_V7 is not set
+CONFIG_ARCH_AT91=y
+CONFIG_SOC_AT91RM9200=y
+CONFIG_SOC_AT91SAM9=y
+CONFIG_AEABI=y
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_ARM_ATAG_DTB_COMPAT=y
+CONFIG_CMDLINE="console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
+CONFIG_KEXEC=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_CFG80211=y
+CONFIG_MAC80211=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_DATAFLASH=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_GLUEBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_ATMEL_TCLIB=y
+CONFIG_ATMEL_SSC=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+CONFIG_MACB=y
+CONFIG_DM9000=y
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+CONFIG_DAVICOM_PHY=y
+CONFIG_MICREL_PHY=y
+# CONFIG_WLAN_VENDOR_ADMTEK is not set
+# CONFIG_WLAN_VENDOR_ATH is not set
+# CONFIG_WLAN_VENDOR_ATMEL is not set
+# CONFIG_WLAN_VENDOR_BROADCOM is not set
+# CONFIG_WLAN_VENDOR_CISCO is not set
+# CONFIG_WLAN_VENDOR_INTEL is not set
+# CONFIG_WLAN_VENDOR_INTERSIL is not set
+# CONFIG_WLAN_VENDOR_MARVELL is not set
+# CONFIG_WLAN_VENDOR_MEDIATEK is not set
+CONFIG_RT2X00=y
+CONFIG_RT2800USB=y
+CONFIG_RT2800USB_RT53XX=y
+# CONFIG_WLAN_VENDOR_REALTEK is not set
+# CONFIG_WLAN_VENDOR_RSI is not set
+# CONFIG_WLAN_VENDOR_ST is not set
+# CONFIG_WLAN_VENDOR_TI is not set
+# CONFIG_WLAN_VENDOR_ZYDAS is not set
+# CONFIG_WLAN_VENDOR_QUANTENNA is not set
+CONFIG_INPUT_POLLDEV=y
+CONFIG_INPUT_JOYDEV=y
+CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_QT1070=y
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ADS7846=y
+# CONFIG_SERIO is not set
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C_AT91=y
+CONFIG_I2C_GPIO=y
+CONFIG_SPI=y
+CONFIG_SPI_ATMEL=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_SUPPLY=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
+CONFIG_MFD_ATMEL_HLCDC=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_MEDIA_CAMERA_SUPPORT=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_SOC_CAMERA=y
+CONFIG_VIDEO_ATMEL_ISI=y
+CONFIG_DRM=y
+CONFIG_DRM_ATMEL_HLCDC=y
+CONFIG_DRM_PANEL_SIMPLE=y
+CONFIG_FB_ATMEL=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+CONFIG_BACKLIGHT_ATMEL_LCDC=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_ACM=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_FTDI_SIO=y
+CONFIG_USB_SERIAL_PL2303=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_AT91=y
+CONFIG_USB_ATMEL_USBA=y
+CONFIG_USB_G_SERIAL=y
+CONFIG_MMC=y
+CONFIG_MMC_ATMELMCI=y
+CONFIG_MMC_SPI=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_PWM=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_RV3029C2=y
+CONFIG_RTC_DRV_AT91RM9200=y
+CONFIG_RTC_DRV_AT91SAM9=y
+CONFIG_DMADEVICES=y
+CONFIG_AT_HDMAC=y
+CONFIG_STAGING=y
+CONFIG_FB_TFT=y
+CONFIG_FB_TFT_ILI9341=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_AT91_ADC=y
+CONFIG_PWM=y
+CONFIG_PWM_ATMEL=y
+CONFIG_PWM_ATMEL_HLCDC_PWM=y
+CONFIG_PWM_ATMEL_TCB=y
+CONFIG_EXT4_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+# CONFIG_CRYPTO_ECHAINIV is not set
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_USER_API_HASH=y
+CONFIG_CRYPTO_USER_API_SKCIPHER=y
+# CONFIG_CRYPTO_HW is not set
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_ACORN_8x8=y
+CONFIG_FONT_MINI_4x6=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
diff --git a/defconfig b/defconfig
new file mode 100644
index 000000000..896a6b0b0
--- /dev/null
+++ b/defconfig
@@ -0,0 +1,214 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_ARCH_MULTI_V4T=y
+CONFIG_ARCH_MULTI_V5=y
+# CONFIG_ARCH_MULTI_V7 is not set
+CONFIG_ARCH_AT91=y
+CONFIG_SOC_AT91RM9200=y
+CONFIG_SOC_AT91SAM9=y
+CONFIG_AEABI=y
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_ARM_ATAG_DTB_COMPAT=y
+CONFIG_CMDLINE="console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
+CONFIG_KEXEC=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_CFG80211=y
+CONFIG_MAC80211=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_DATAFLASH=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_GLUEBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_ATMEL_TCLIB=y
+CONFIG_ATMEL_SSC=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+CONFIG_MACB=y
+CONFIG_DM9000=y
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+CONFIG_DAVICOM_PHY=y
+CONFIG_MICREL_PHY=y
+# CONFIG_WLAN_VENDOR_ADMTEK is not set
+# CONFIG_WLAN_VENDOR_ATH is not set
+# CONFIG_WLAN_VENDOR_ATMEL is not set
+# CONFIG_WLAN_VENDOR_BROADCOM is not set
+# CONFIG_WLAN_VENDOR_CISCO is not set
+# CONFIG_WLAN_VENDOR_INTEL is not set
+# CONFIG_WLAN_VENDOR_INTERSIL is not set
+# CONFIG_WLAN_VENDOR_MARVELL is not set
+# CONFIG_WLAN_VENDOR_MEDIATEK is not set
+CONFIG_RT2X00=y
+CONFIG_RT2800USB=y
+CONFIG_RT2800USB_RT53XX=y
+# CONFIG_WLAN_VENDOR_REALTEK is not set
+# CONFIG_WLAN_VENDOR_RSI is not set
+# CONFIG_WLAN_VENDOR_ST is not set
+# CONFIG_WLAN_VENDOR_TI is not set
+# CONFIG_WLAN_VENDOR_ZYDAS is not set
+# CONFIG_WLAN_VENDOR_QUANTENNA is not set
+CONFIG_INPUT_POLLDEV=y
+CONFIG_INPUT_JOYDEV=y
+CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_QT1070=y
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ADS7846=y
+# CONFIG_SERIO is not set
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C_AT91=y
+CONFIG_I2C_GPIO=y
+CONFIG_SPI=y
+CONFIG_SPI_ATMEL=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_SUPPLY=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
+CONFIG_MFD_ATMEL_HLCDC=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_MEDIA_CAMERA_SUPPORT=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_SOC_CAMERA=y
+CONFIG_VIDEO_ATMEL_ISI=y
+CONFIG_DRM=y
+CONFIG_DRM_ATMEL_HLCDC=y
+CONFIG_DRM_PANEL_SIMPLE=y
+CONFIG_FB_ATMEL=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+CONFIG_BACKLIGHT_ATMEL_LCDC=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_ACM=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_FTDI_SIO=y
+CONFIG_USB_SERIAL_PL2303=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_AT91=y
+CONFIG_USB_ATMEL_USBA=y
+CONFIG_USB_G_SERIAL=y
+CONFIG_MMC=y
+CONFIG_MMC_ATMELMCI=y
+CONFIG_MMC_SPI=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_PWM=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_RV3029C2=y
+CONFIG_RTC_DRV_AT91RM9200=y
+CONFIG_RTC_DRV_AT91SAM9=y
+CONFIG_DMADEVICES=y
+CONFIG_AT_HDMAC=y
+CONFIG_STAGING=y
+CONFIG_FB_TFT=y
+CONFIG_FB_TFT_ILI9341=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_AT91_ADC=y
+CONFIG_PWM=y
+CONFIG_PWM_ATMEL=y
+CONFIG_PWM_ATMEL_HLCDC_PWM=y
+CONFIG_PWM_ATMEL_TCB=y
+CONFIG_EXT4_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_AUTOFS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+# CONFIG_CRYPTO_ECHAINIV is not set
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_USER_API_HASH=y
+CONFIG_CRYPTO_USER_API_SKCIPHER=y
+# CONFIG_CRYPTO_HW is not set
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_ACORN_8x8=y
+CONFIG_FONT_MINI_4x6=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 936d401f2..987aadd93 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -107,7 +107,7 @@ struct atmel_uart_char {
  * at91: 6 USARTs and one DBGU port (SAM9260)
  * samx7: 3 USARTs and 5 UARTs
  */
-#define ATMEL_MAX_UART		8
+#define ATMEL_MAX_UART		10
 
 /*
  * We wrap our port structure around the generic uart_port.
diff --git a/modules/lib/modules/4.19.131+/build b/modules/lib/modules/4.19.131+/build
new file mode 120000
index 000000000..1e98ac12f
--- /dev/null
+++ b/modules/lib/modules/4.19.131+/build
@@ -0,0 +1 @@
+/home/acme/arietta/linux-4.19.131
\ No newline at end of file
diff --git a/modules/lib/modules/4.19.131+/modules.alias b/modules/lib/modules/4.19.131+/modules.alias
new file mode 100644
index 000000000..ba76e1815
--- /dev/null
+++ b/modules/lib/modules/4.19.131+/modules.alias
@@ -0,0 +1 @@
+# Aliases extracted from modules themselves.
diff --git a/modules/lib/modules/4.19.131+/modules.dep b/modules/lib/modules/4.19.131+/modules.dep
new file mode 100644
index 000000000..e69de29bb
diff --git a/modules/lib/modules/4.19.131+/modules.devname b/modules/lib/modules/4.19.131+/modules.devname
new file mode 100644
index 000000000..e69de29bb
diff --git a/modules/lib/modules/4.19.131+/modules.softdep b/modules/lib/modules/4.19.131+/modules.softdep
new file mode 100644
index 000000000..5554ccca7
--- /dev/null
+++ b/modules/lib/modules/4.19.131+/modules.softdep
@@ -0,0 +1 @@
+# Soft dependencies extracted from modules themselves.
diff --git a/modules/lib/modules/4.19.131+/modules.symbols b/modules/lib/modules/4.19.131+/modules.symbols
new file mode 100644
index 000000000..618c345f7
--- /dev/null
+++ b/modules/lib/modules/4.19.131+/modules.symbols
@@ -0,0 +1 @@
+# Aliases for symbols, used by symbol_request().
diff --git a/modules/lib/modules/4.19.131+/source b/modules/lib/modules/4.19.131+/source
new file mode 120000
index 000000000..1e98ac12f
--- /dev/null
+++ b/modules/lib/modules/4.19.131+/source
@@ -0,0 +1 @@
+/home/acme/arietta/linux-4.19.131
\ No newline at end of file