HSGQ new ISP can't get connected #353
Unanswered
johnbaker26222
asked this question in
Help
Replies: 31 comments 2 replies
-
|
what is the model of original ONU? can you access the WebGUI of original ONU? |
Beta Was this translation helpful? Give feedback.
0 replies
-
|
Yes I can access the webpage.
Sent from Proton Mail Android
…-------- Original Message --------
On 12/20/24 08:52, Anime4000 wrote:
what is the model of original ONU? can you access the WebGUI of original ONU?
—
Reply to this email directly, [view it on GitHub](#350 (comment)), or [unsubscribe](https://github.com/notifications/unsubscribe-auth/BAGCL2UEDCVOG66UQFN5HTT2GNZ47AVCNFSM6AAAAABT4M3DTKVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDKNJWGEYDGMBZG4).
You are receiving this because you authored the thread.Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
0 replies
-
|
Beta Was this translation helpful? Give feedback.
0 replies
-
You only need the following parameters (in the red box) to fill in the sfp
|
Beta Was this translation helpful? Give feedback.
0 replies
-
<Value Name="PON_VENDOR_ID" Value="T3TH"/>
<Value Name="OMCI_VENDOR_PRODUCT_CODE" Value="15"/>
# flash all | grep PRODUCT
<Value Name="HW_CWMP_PRODUCTCLASS" Value="T626Pro"/>
<Value Name="OMCI_VENDOR_PRODUCT_CODE" Value="15"/>
<Value Name="RTK_DEVID_PRODUCTCLASS" Value=""/>
# flash all | grep GPON
<Value Name="GPON_ONU_MODEL" Value="T626Pro"/>
<Value Name="GPON_SN" Value="T3TH65A3EEFA"/>
<Value Name="GPON_PLOAM_FORMAT" Value="1"/>
<Value Name="GPON_PLOAM_PASSWD" Value="36303030303137353131"/>
# flash all | grep SW
<Value Name="SUPER_PASSWORD" Value="realtek"/>
<Value Name="HW_WLAN0_11N_TRSWITCH" Value="0"/>
<Value Name="HW_WLAN0_11N_TRSWPAPE_C9" Value="0"/>
<Value Name="HW_WLAN0_11N_TRSWPAPE_CC" Value="0"/>
<Value Name="USER_PASSWORD" Value="user"/>
<Value Name="SUSER_PASSWORD" Value="admin"/>
<Value Name="E8BDUSER_PASSWORD" Value="Stel$864"/>
<Value Name="LOID_PASSWD" Value=""/>
<Value Name="LOID_PASSWD_OLD" Value=""/>
<Value Name="GPON_PLOAM_PASSWD" Value="36303030303137353131"/>
<Value Name="OMCI_SW_VER1" Value="V1.0.0.5"/>
<Value Name="OMCI_SW_VER2" Value="V1.0.0.5"/>
<Value Name="RTK_DEVINFO_SWVER" Value=""/>
<Dir Name="SW_PORT_TBL"> <!--index=0-->
<Dir Name="SW_PORT_TBL"> <!--index=1-->
# flash all | grep HW
<Dir Name="HW_MIB_TABLE">
<Value Name="HW_RF_TYPE" Value="7"/>
<Value Name="HW_WLAN0_TX_POWER_CCK_A" Value="00,00,00,00,00,00,00,00,00,00,00,00,00,00"/>
<Value Name="HW_WLAN0_TX_POWER_CCK_B" Value="00,00,00,00,00,00,00,00,00,00,00,00,00,00"/>
<Value Name="HW_WLAN0_TX_POWER_HT40_1S_A" Value="00,00,00,00,00,00,00,00,00,00,00,00,00,00"/>
<Value Name="HW_WLAN0_TX_POWER_HT40_1S_B" Value="00,00,00,00,00,00,00,00,00,00,00,00,00,00"/>
<Value Name="HW_WLAN0_TX_POWER_DIFF_HT40_2S" Value="00,00,00,00,00,00,00,00,00,00,00,00,00,00"/>
<Value Name="HW_WLAN0_TX_POWER_DIFF_HT20" Value="00,00,00,00,00,00,00,00,00,00,00,00,00,00"/>
<Value Name="HW_WLAN0_TX_POWER_DIFF_OFDM" Value="00,00,00,00,00,00,00,00,00,00,00,00,00,00"/>
<Value Name="HW_WLAN0_11N_TSSI1" Value="0"/>
<Value Name="HW_WLAN0_11N_TSSI2" Value="0"/>
<Value Name="HW_WLAN0_11N_THER" Value="0"/>
<Value Name="HW_WLAN0_11N_THER_2" Value="0"/>
<Value Name="HW_WLAN0_11N_PA_TYPE" Value="0"/>
<Value Name="HW_WLAN0_REG_DOMAIN" Value="1"/>
<Value Name="HW_WLAN0_11N_TRSWITCH" Value="0"/>
<Value Name="HW_WLAN0_11N_TRSWPAPE_C9" Value="0"/>
<Value Name="HW_WLAN0_11N_TRSWPAPE_CC" Value="0"/>
<Value Name="HW_ANT_DIVERSITY" Value="0"/>
<Value Name="HW_TX_ANT" Value="0"/>
<Value Name="HW_CS_THRESHOLD" Value="11"/>
<Value Name="HW_CCA_MODE" Value="1"/>
<Value Name="HW_PHY_TYPE" Value="0"/>
<Value Name="HW_WLAN_LED_TYPE" Value="7"/>
<Value Name="HW_SERIAL_NO" Value="T3TH65A3EEFA"/>
<Value Name="HW_FON_KEYWORD" Value="63,62,68,4a,75,3c,65,cd,7b,75,e5,2d,a9,80,72,8c,97,fc,bd,9b,37,51,d9,e3,82,92,68,a1,07,ae,a0,b5"/>
<Value Name="HW_WLAN0_11N_XCAP" Value="0"/>
<Value Name="HW_WLAN0_11N_XCAP_2" Value="0"/>
<Value Name="HW_WLAN0_11N_TARGET_PWR" Value="0"/>
<Value Name="HW_WLAN0_COUNTRYCODE" Value="1"/>
<Value Name="HW_WLAN1_COUNTRYCODE" Value="1"/>
<Value Name="HW_WLAN0_COUNTRYSTR" Value="US"/>
<Value Name="HW_WLAN1_COUNTRYSTR" Value="US"/>
<Value Name="HW_CWMP_MANUFACTURER" Value="00,00"/>
<Value Name="HW_CWMP_PRODUCTCLASS" Value="T626Pro"/>
<Value Name="HW_HWVER" Value="V1.0"/>
<Value Name="RTK_DEVINFO_HWVER" Value=""/> |
Beta Was this translation helpful? Give feedback.
0 replies
-
|
@johnbaker26222 After filling out, have you rebooted sfp? Please show PON and Settings of web for sfp after reboot |
Beta Was this translation helpful? Give feedback.
0 replies
-
|
|
Beta Was this translation helpful? Give feedback.
0 replies
-
|
@johnbaker26222 Please upgrade firmware to 220923 https://github.com/Anime4000/RTL960x/blob/main/Firmware/DFP-34X-2C2/M110_sfp_ODI_220923.tar then using telnet with command flash set OMCI_OLT_MODE 3 |
Beta Was this translation helpful? Give feedback.
0 replies
-
Ok done but still same not getting past 03 status. I really wish there were logs I could check somewhere. <Config Name="ROOT">
<Dir Name="HW_MIB_TABLE">
<Value Name="SUPER_NAME" Value="adsl"/>
<Value Name="SUPER_PASSWORD" Value="realtek"/>
<Value Name="TEST_MAC_ADDR" Value="realtek"/>
<Value Name="ELAN_MAC_ADDR" Value="6420e1a3eefa"/>
<Value Name="WLAN_MAC_ADDR" Value="6420e1a3eefa"/>
<Value Name="MAC_KEY" Value="bd7f3334b22b27b1269d4742b34123ef"/>
<Value Name="RESTORE_DEFAULT_EN" Value="1"/>
<Value Name="WAN_PHY_PORT" Value="4"/>
<Value Name="LASER_POLARITY_TYPE" Value="0"/>
<Value Name="PON_DETECT_ENABLE" Value="1"/>
<Value Name="HW_RF_TYPE" Value="7"/>
<Value Name="HW_WLAN0_TX_POWER_CCK_A" Value="00,00,00,00,00,00,00,00,00,00,00,00,00,00"/>
<Value Name="HW_WLAN0_TX_POWER_CCK_B" Value="00,00,00,00,00,00,00,00,00,00,00,00,00,00"/>
<Value Name="HW_WLAN0_TX_POWER_HT40_1S_A" Value="00,00,00,00,00,00,00,00,00,00,00,00,00,00"/>
<Value Name="HW_WLAN0_TX_POWER_HT40_1S_B" Value="00,00,00,00,00,00,00,00,00,00,00,00,00,00"/>
<Value Name="HW_WLAN0_TX_POWER_DIFF_HT40_2S" Value="00,00,00,00,00,00,00,00,00,00,00,00,00,00"/>
<Value Name="HW_WLAN0_TX_POWER_DIFF_HT20" Value="00,00,00,00,00,00,00,00,00,00,00,00,00,00"/>
<Value Name="HW_WLAN0_TX_POWER_DIFF_OFDM" Value="00,00,00,00,00,00,00,00,00,00,00,00,00,00"/>
<Value Name="HW_WLAN0_11N_TSSI1" Value="0"/>
<Value Name="HW_WLAN0_11N_TSSI2" Value="0"/>
<Value Name="HW_WLAN0_11N_THER" Value="0"/>
<Value Name="HW_WLAN0_11N_THER_2" Value="0"/>
<Value Name="HW_WLAN0_11N_PA_TYPE" Value="0"/>
<Value Name="HW_WLAN0_REG_DOMAIN" Value="1"/>
<Value Name="HW_WLAN0_11N_TRSWITCH" Value="0"/>
<Value Name="HW_WLAN0_11N_TRSWPAPE_C9" Value="0"/>
<Value Name="HW_WLAN0_11N_TRSWPAPE_CC" Value="0"/>
<Value Name="HW_ANT_DIVERSITY" Value="0"/>
<Value Name="HW_TX_ANT" Value="0"/>
<Value Name="HW_CS_THRESHOLD" Value="11"/>
<Value Name="HW_CCA_MODE" Value="1"/>
<Value Name="HW_PHY_TYPE" Value="0"/>
<Value Name="HW_WLAN_LED_TYPE" Value="7"/>
<Value Name="BYTE" Value="255"/>
<Value Name="WORD" Value="65535"/>
<Value Name="DWORD" Value="4294967295"/>
<Value Name="INT1" Value="2147483647"/>
<Value Name="INT2" Value="-2147483648"/>
<Value Name="WIFI_SUPPORT" Value="0"/>
<Value Name="HW_SERIAL_NO" Value="T3TH65A3EEFA"/>
<Value Name="HW_FON_KEYWORD" Value="63,62,68,4a,75,3c,65,cd,7b,75,e5,2d,a9,80,72,8c,97,fc,bd,9b,37,51,d9,e3,82,92,68,a1,07,ae,a0,b5"/>
<Value Name="HW_WLAN0_11N_XCAP" Value="0"/>
<Value Name="HW_WLAN0_11N_XCAP_2" Value="0"/>
<Value Name="HW_WLAN0_11N_TARGET_PWR" Value="0"/>
<Value Name="HW_WLAN0_COUNTRYCODE" Value="1"/>
<Value Name="HW_WLAN1_COUNTRYCODE" Value="1"/>
<Value Name="HW_WLAN0_COUNTRYSTR" Value="US"/>
<Value Name="HW_WLAN1_COUNTRYSTR" Value="US"/>
<Value Name="HW_CWMP_MANUFACTURER" Value="T3TH"/>
<Value Name="HW_CWMP_PRODUCTCLASS" Value="T626Pro"/>
<Value Name="HW_HWVER" Value="V1.0"/>
<Value Name="GPON_ONU_MODEL" Value="T626Pro"/>
<Value Name="LAN_SDS_MODE" Value="0"/>
<Value Name="PON_MODE" Value="1"/>
<Value Name="PON_LED_SPEC" Value="0"/>
<Value Name="OUI" Value="64,20,e1"/>
<Value Name="PORT_REMAPPING" Value="00,01,00,00"/>
<Value Name="PON_VENDOR_ID" Value="T3TH"/>
<Value Name="GPON_SN" Value="T3TH65A3EEFA"/>
<Value Name="EPON_ONU_MODEL" Value="T3TH"/>
<Value Name="EPON_EXTONU_MODEL" Value="T626Pro"/>
<Value Name="EPON_SILENT_MODE" Value="1"/>
</Dir>
</Config>
<Config Name="ROOT">
<Dir Name="MIB_TABLE">
<Value Name="WAN_MODE" Value="7"/>
<Value Name="LAN_IP_ADDR" Value="192.168.100.1"/>
<Value Name="LAN_SUBNET" Value="255.255.255.0"/>
<Value Name="LAN_ENABLE_IP2" Value="0"/>
<Value Name="LAN_IP_ADDR2" Value="192.168.100.1"/>
<Value Name="LAN_SUBNET2" Value="255.255.255.0"/>
<Value Name="LAN_RIP" Value="0"/>
<Value Name="LAN_AUTOSEARCH" Value="0"/>
<Value Name="DNS_MODE" Value="0"/>
<Value Name="DNS1" Value="0.0.0.0"/>
<Value Name="DNS2" Value="0.0.0.0"/>
<Value Name="DNS3" Value="0.0.0.0"/>
<Value Name="ADSL_MODE" Value="83"/>
<Value Name="ADSL_OLR" Value="3"/>
<Value Name="USER_NAME" Value="user"/>
<Value Name="USER_PASSWORD" Value="user"/>
<Value Name="DEVICE_TYPE" Value="1"/>
<Value Name="INIT_LINE" Value="1"/>
<Value Name="INIT_SCRIPT" Value="1"/>
<Value Name="SNMP_SYS_NAME" Value="Modem/Router"/>
<Value Name="VC_AUTOSEARCH" Value="0"/>
<Value Name="BR_AGEING_TIME" Value="7200"/>
<Value Name="BR_STP_ENABLED" Value="0"/>
<Value Name="MP_MODE" Value="4"/>
<Value Name="SPC_ENABLED" Value="0"/>
<Value Name="SPC_IPTYPE" Value="0"/>
<Value Name="MP_FIN" Value="1"/>
<Value Name="MULTI_LINGUAL_STATE" Value="en"/>
<Value Name="TFTP_SERVER_ADDR" Value="tftp://0.0.0.0"/>
<Value Name="POSIX_TZ_STRING" Value=""/>
<Value Name="BOOT_FILENAME" Value=""/>
<Value Name="UPNP" Value="0"/>
<Value Name="UPNP_EXT_ITF" Value="255"/>
<Value Name="SYSLOG_LOG_LEVEL" Value="0"/>
<Value Name="SYSLOG_DISPLAY_LEVEL" Value="0"/>
<Value Name="SUSER_NAME" Value="admin"/>
<Value Name="SUSER_PASSWORD" Value="admin"/>
<Value Name="E8BDUSER_NAME" Value="administrator"/>
<Value Name="E8BDUSER_PASSWORD" Value="Stel$864"/>
<Value Name="ADSL_TONE" Value="00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00"/>
<Value Name="DIRECT_BRIDGE_MODE" Value="1"/>
<Value Name="ADSL_HIGH_INP" Value="0"/>
<Value Name="SYSLOG" Value="0"/>
<Value Name="MAXLOGLEN" Value="16384"/>
<Value Name="ADSLDBG" Value="0"/>
<Value Name="MIB_ETH_MAC_CTRL" Value="0"/>
<Value Name="MIB_WLAN_MAC_CTRL" Value="0"/>
<Value Name="SNOOPING_ENABLED" Value="0"/>
<Value Name="LOID" Value="12345678"/>
<Value Name="LOID_PASSWD" Value="123456"/>
<Value Name="LOID_OLD" Value="12345678"/>
<Value Name="LOID_PASSWD_OLD" Value="123456"/>
<Value Name="PROVINCE_TRAP_PPPOE_TRAFFIC" Value="0"/>
<Value Name="GPON_PLOAM_FORMAT" Value="1"/>
<Value Name="GPON_PLOAM_PASSWD" Value="36303030303137353131"/>
<Value Name="OMCI_DBGLVL" Value="2"/>
<Value Name="OMCI_LOGFILE" Value="0"/>
<Value Name="OMCI_PORT_TYPE" Value="1"/>
<Value Name="DUAL_MGMT_MODE" Value="1"/>
<Value Name="OMCI_CUSTOM_BDP" Value="258"/>
<Value Name="OMCI_CUSTOM_RDP" Value="4"/>
<Value Name="OMCI_CUSTOM_MCAST" Value="0"/>
<Value Name="OMCI_CUSTOM_ME" Value="65536"/>
<Value Name="OMCI_VENDOR_PRODUCT_CODE" Value="15"/>
<Value Name="OMCI_FAKE_OK" Value="1"/>
<Value Name="OMCI_VEIP_SLOT_ID" Value="255"/>
<Value Name="OMCI_WAN_QOS_QUEUE_NUM" Value="1"/>
<Value Name="RTK_IGMP_DBGEN" Value="0"/>
<Value Name="RTK_IGMP_DROPV1" Value="0"/>
<Value Name="RTK_IGMP_VIDTYPE" Value="0"/>
<Value Name="RTK_IGMP_TAGDECISION" Value="0"/>
<Value Name="VLAN_CFG_TYPE" Value="1"/>
<Value Name="VLAN_MANU_MODE" Value="1"/>
<Value Name="VLAN_MANU_TAG_VID" Value="100"/>
<Value Name="VLAN_MANU_TAG_PRI" Value="255"/>
<Value Name="OMCI_OLT_MODE" Value="3"/>
<Value Name="OMCI_SW_VER1" Value="V1.0.0.5"/>
<Value Name="OMCI_SW_VER2" Value="V1.0.0.5"/>
<Value Name="OMCC_VER" Value="128"/>
<Value Name="OMCI_TM_OPT" Value="2"/>
<Value Name="OMCI_LOGFILE_MASK" Value="2"/>
<Value Name="REBOOT_TIME" Value="0"/>
<Value Name="DHCP_PORT_FILTER" Value="1"/>
<Value Name="NTP_EXT_ITF" Value="65535"/>
<Value Name="FIBER_MODE" Value="0"/>
<Value Name="RTK_DEVID_MANUFACTURER" Value="T3TH"/>
<Value Name="RTK_DEVID_OUI" Value=""/>
<Value Name="RTK_DEVID_PRODUCTCLASS" Value=""/>
<Value Name="RTK_DEVINFO_SPECVER" Value=""/>
<Value Name="RTK_DEVINFO_SWVER" Value=""/>
<Value Name="RTK_DEVINFO_HWVER" Value=""/>
<Value Name="DEVICE_NAME" Value="RTK_GW"/>
</Dir>
<Dir Name="ATM_VC_TBL"> <!--index=0-->
<Value Name="ifIndex" Value="130816"/>
<Value Name="VPI" Value="0"/>
<Value Name="QoS" Value="0"/>
<Value Name="VCI" Value="0"/>
<Value Name="PCR" Value="0"/>
<Value Name="SCR" Value="0"/>
<Value Name="MBS" Value="0"/>
<Value Name="CDVT" Value="0"/>
<Value Name="Encap" Value="0"/>
<Value Name="NAPT" Value="0"/>
<Value Name="ChannelMode" Value="0"/>
<Value Name="BridgeType" Value="2"/>
<Value Name="pppUser" Value=""/>
<Value Name="pppPasswd" Value=""/>
<Value Name="pppAuth" Value="0"/>
<Value Name="pppACName" Value=""/>
<Value Name="pppServiceName" Value=""/>
<Value Name="pppConnectType" Value="0"/>
<Value Name="pppIdleTime" Value="0"/>
<Value Name="enableIGMP" Value="0"/>
<Value Name="ChannelAddrType" Value="0"/>
<Value Name="RIP" Value="0"/>
<Value Name="LocalIPAddr" Value="0.0.0.0"/>
<Value Name="RemoteIPAddr" Value="0.0.0.0"/>
<Value Name="DefaultGW" Value="0"/>
<Value Name="MTU" Value="0"/>
<Value Name="ChannelStatus" Value="1"/>
<Value Name="SubnetMask" Value="0.0.0.0"/>
<Value Name="Ipunnum" Value="0"/>
<Value Name="DNSMode" Value="0"/>
<Value Name="DNSV4IPAddr1" Value="0.0.0.0"/>
<Value Name="DNSV4IPAddr2" Value="0.0.0.0"/>
<Value Name="vlan" Value="1"/>
<Value Name="vid" Value="100"/>
<Value Name="vprio" Value="0"/>
<Value Name="vpass" Value="0"/>
<Value Name="itfGroup" Value="0"/>
<Value Name="itfGroupNum" Value="0"/>
<Value Name="mVid" Value="0"/>
<Value Name="cpePppIfIndex" Value="0"/>
<Value Name="cpeIpIndex" Value="0"/>
<Value Name="WanName" Value=""/>
<Value Name="applicationtype" Value="2"/>
<Value Name="MacAddr" Value="6420e1a3eefb"/>
</Dir>
<Dir Name="SW_PORT_TBL"> <!--index=0-->
<Value Name="PVCInterface" Value="65535"/>
<Value Name="InterfaceGroup" Value="0"/>
<Value Name="PVID" Value="0"/>
<Value Name="LinkMode" Value="4"/>
<Value Name="VLAN on LAN Enabled" Value="0"/>
<Value Name="VLAN on LAN InterfaceGroup" Value="0"/>
<Value Name="VID" Value="0"/>
</Dir>
<Dir Name="SW_PORT_TBL"> <!--index=1-->
<Value Name="PVCInterface" Value="65535"/>
<Value Name="InterfaceGroup" Value="0"/>
<Value Name="PVID" Value="1"/>
<Value Name="LinkMode" Value="4"/>
<Value Name="VLAN on LAN Enabled" Value="0"/>
<Value Name="VLAN on LAN InterfaceGroup" Value="0"/>
<Value Name="VID" Value="0"/>
</Dir>
<Dir Name="MAC_BASE_DHCP_TBL">
</Dir>
<Dir Name="AUTO_PVC_SEARCH_TBL"> <!--index=0-->
<Value Name="VPI" Value="0"/>
<Value Name="VCI" Value="35"/>
</Dir>
<Dir Name="AUTO_PVC_SEARCH_TBL"> <!--index=1-->
<Value Name="VPI" Value="8"/>
<Value Name="VCI" Value="35"/>
</Dir>
<Dir Name="AUTO_PVC_SEARCH_TBL"> <!--index=2-->
<Value Name="VPI" Value="0"/>
<Value Name="VCI" Value="43"/>
</Dir>
<Dir Name="AUTO_PVC_SEARCH_TBL"> <!--index=3-->
<Value Name="VPI" Value="0"/>
<Value Name="VCI" Value="51"/>
</Dir>
<Dir Name="AUTO_PVC_SEARCH_TBL"> <!--index=4-->
<Value Name="VPI" Value="0"/>
<Value Name="VCI" Value="59"/>
</Dir>
<Dir Name="AUTO_PVC_SEARCH_TBL"> <!--index=5-->
<Value Name="VPI" Value="8"/>
<Value Name="VCI" Value="43"/>
</Dir>
<Dir Name="AUTO_PVC_SEARCH_TBL"> <!--index=6-->
<Value Name="VPI" Value="8"/>
<Value Name="VCI" Value="51"/>
</Dir>
<Dir Name="AUTO_PVC_SEARCH_TBL"> <!--index=7-->
<Value Name="VPI" Value="8"/>
<Value Name="VCI" Value="59"/>
</Dir>
<Dir Name="PPPOE_SESSION_TBL">
</Dir>
<Dir Name="RIP_TBL">
</Dir>
<Dir Name="DHCP_RESERVED_IPADDR_TBL">
</Dir>
<Dir Name="EPON_LLID_TBL">
</Dir>
</Config>
#
 |
Beta Was this translation helpful? Give feedback.
0 replies
-
|
Not sure why the SW version is correct in the terminal but not on the webpage? I tried changing on the webpage, committing and rebooting, and its back to what is below. I did update the firmware to the link provided above.
|
Beta Was this translation helpful? Give feedback.
0 replies
-
|
please update again to upgrade image 2, then reset factory remember backup MAC and MACKEY (to refill after reset factory) flash_eraseall /dev/mtd3 fill all info necessary. You need to change sw version the same ONT from ISP |
Beta Was this translation helpful? Give feedback.
0 replies
-
|
and also, you can try to change vendor id to HWTC @johnbaker26222 |
Beta Was this translation helpful? Give feedback.
0 replies
-
|
With HWTC in the vendor id I get initial status instead of the LOID error. And it again goes back to O2, then O3 status. Not sure if that is better or worse? Also I am assuming the "Material Code" is the PLOAM? See first photo I have of the back of the ONT. Also the "True SN", I wonder if that needs to be somewhere? I tried it under Device SN but same same.
|
Beta Was this translation helpful? Give feedback.
0 replies
-
|
please check: 1, what is connector from your ISP and sfp, is SC/APC (green) or SC/UPC (blue)? |
Beta Was this translation helpful? Give feedback.
0 replies
-
|
Hmm sorry don't understand the first question. On the second, I'm just using a media converter to Ethernet that my SFP is plugged into.
Sent from Proton Mail Android
…-------- Original Message --------
On 12/20/24 20:12, vuducdong wrote:
***@***.***(https://github.com/johnbaker26222)
please check:
1, what is connector from your ISP and sfp, is SC/APC (green) or SC/UPC (blue)?
2, what device are you attaching the sfp to?
—
Reply to this email directly, [view it on GitHub](#350 (comment)), or [unsubscribe](https://github.com/notifications/unsubscribe-auth/BAGCL2RRCSVCRX2MAJMD2TD2GQJUZAVCNFSM6AAAAABT4M3DTKVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDKNJWHE3TQNJYGM).
You are receiving this because you were mentioned.Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
0 replies
-
|
Ohh sorry I understand now. It's green.
Sent from Proton Mail Android
…-------- Original Message --------
On 12/20/24 20:12, vuducdong wrote:
***@***.***(https://github.com/johnbaker26222)
please check:
1, what is connector from your ISP and sfp, is SC/APC (green) or SC/UPC (blue)?
2, what device are you attaching the sfp to?
—
Reply to this email directly, [view it on GitHub](#350 (comment)), or [unsubscribe](https://github.com/notifications/unsubscribe-auth/BAGCL2RRCSVCRX2MAJMD2TD2GQJUZAVCNFSM6AAAAABT4M3DTKVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDKNJWHE3TQNJYGM).
You are receiving this because you were mentioned.Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
0 replies
-
Both are green, right? sfp HSQG and fiber cable from ISP. Some case will have problem with RX power above -24dBm, need to fix it from -16 to -23 dBm. You can try firmware version with add mib for huawei from user Brazil. (Looking in threads of RTL960x) |
Beta Was this translation helpful? Give feedback.
0 replies
-
|
|
Beta Was this translation helpful? Give feedback.
0 replies
-
|
There are 2 ways: 1, change sfp to green 2, use the blue to green converter (adapter and patch cord)
|
Beta Was this translation helpful? Give feedback.
0 replies
-
|
Ahh cool thanks you have been a tremendous help! Is there a y way to get useful lots from my SFP device? |
Beta Was this translation helpful? Give feedback.
0 replies
-
I don't understand, what do you want ? |
Beta Was this translation helpful? Give feedback.
0 replies
-
Logs from the SFP device so I can see exactly what is going on. I did a chip off on my ISPs ONU which helped me get passwords for the superadmin user along with console logins. I found the ctromfile.cfg (romfile.cfg) file which I believe contains all the relevant info to connect with. There are multiple vendor ids. I've tried many of them. Only the HWTC one allows an O5 state for about 5 minutes then it goes back to O2 and O3. I can see my VLAN ID is 100. Also was able to get my pppoe login data. Still no dice. <EPON>
<ONU Type="HGU" VendorID="MTKc" Model="EPON" HWVer="PT632V1.0" SWVer="PT632-CT-V1.0" FWVer="12345e" GEPortNum="1" FEPortNum="3" POTSPortNum="1" E1PortNum="0" USBPortNum="1" WLANPortNum="1" ADSL2PortNum="0" VDSL2PortNum="0" USQueuesNum="8" DSQueuesNum="8" USQueueMaxPerPort="8" DSQueueMaxPerPort="8" BatteryBackup="No" IPv6Aware="Yes" PowerSupply="1" ServiceSLA="5" PortMACAgingTime="1500" FECAbility="3" FECMode="No" />
<PON LLIDNum="8" LLIDUseMask="1" PONIFNum="1" ProtectionType="0" VendorID="0x01F2" Model="0xcce4" Revision="01" Version="12/06/14" Holdover="Yes" HoldoverTime="100" ActivePONIF="0" Temperature="32" SupplyVoltage="34" TxBiasCurrent="3456" RxPower="879" TxPower="3456" TLosOptical="2" TLosMAC="55" />
<PowerSaving Capability="0" EarlyWakeup="Yes" EarlyWakeupActive="Yes" MaxDuration="10000000" />
<LOIDAuth LOID0="" Password0="" DesiredAuthType="LOID_PWD" AuthStatus="" ErrorCode="" />
<SoftImage Main="0" Active="0" Version0="PT632-CT-V1.0" Valid0="1" Version1="PT632-CT-V1.0" Valid1="0" />
<ServiceSLA Enable="1" BestScheduleScheme="0/1/2" HighPriBoundary="86" CycleLength="8686200" Num="4" PriQ0="0" FixedSize0="64" FixedBW0="0" GrantBW0="256" BestBW0="256" WRR0="30" PriQ1="1" FixedSize1="64" FixedBW1="0" GrantBW1="256" BestBW1="0" WRR1="20" PriQ2="2" FixedSize2="64" FixedBW2="0" GrantBW2="256" BestBW2="0" WRR2="40" PriQ3="3" FixedSize3="0" FixedBW3="0" GrantBW3="512" BestBW3="0" WRR3="10" />
</EPON>
<Oam>
<Entry LocalOUI="0x000db6" LocalVendorInfo="0x4d150100" UseCtc="Yes" DebugLevel="0" DebugLlidMask="1" LanDbg="0" />
<CTC OUI="0x111111" Version="MTK1.0" Active="Yes" DiscoveryState="0" DebugLevel="0" />
<CUC CfgCnt="0" />
</Oam>
<GPON>
<Common Enable="1" CurrentAttribute="Version" OMCI_SoftWare_Image_State="SOFTWARE_IMAGE_STATE_S3_0" />
<ONU Version="RP0201" VendorId="T3TH" SerialNumber="T3TH65A3EEFA" Password="" TMOption="2" ONUSurvivalTime="10" ExtendedTClayer="3" EquipmentId="PT632" OMCCVersion="96" VendorProCode="340" SecurityCap="1" TotalPQNum="248" TotalTSNum="31" TotalGEMPortNum="256" ConnectivityCap="7f" QosConfFlex="0" MaxPorts="8" PortList1="48,248,47,47,47,47,0,0" EnhancedPSK="01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 00" EmergencyState="0" />
<OLT VendorId="HWTC" EquipmentId="" Version="10" ToD="" />
<ANI TotalTCONTNum="31" SRIndication="1" GEMBlockLength="48" PiggybackDBA="1" SFThd="5" SDThd="9" ONUResponseTime="35000" RxOpticalLevel="" />
<TCONT/>
<GEMPort EncryptionStateALL="32:0#3968:0#2720:0#1440:0#" />
<Trtcm/>
<SoftImage0 Version="V1.0.0.5" Committed="1" Active="1" Valid="1" />
<SoftImage1 Version="V1.0.0.5" Committed="0" Active="0" Valid="1" />
<Capability OperatorID="CTC" SpecVersion="0" ONU_type="0" ONU_PowerCtr="0" />
<LOIDAuth OperatorID="CTC" LOID="2412904630" Password="" AuthStatus="1" />
</GPON>
<PM>
<Entry mode="GPON" classId="" portId="" dataFlag="" attrIndex="" attrData="" />
<EPON portId="" dataFlag="" cycleTime="" status="" set="" clear="" ds_DropEvents="" us_DropEvents="" ds_Octets="" us_Octets="" ds_Frames="" us_Frames="" ds_Broadcast="" us_Broadcast="" ds_Multicast="" us_Multicast="" ds_CRCError="" us_CRCError="" ds_Undersize="" us_Undersize="" ds_Oversize="" us_Oversize="" ds_Fragments="" us_Fragments="" ds_Jabbers="" us_Jabbers="" ds_64Octets="" us_64Octets="" ds_65to127="" us_65to127="" ds_128to255="" us_128to255="" ds_256to511="" us_256to511="" ds_512to1023="" us_512to1023="" ds_1024to1518="" us_1024to1518="" ds_Discards="" us_Discards="" ds_Errors="" us_Errors="" statusChangeTimes="" />
</PM>
<OMCI>
<Entry Version="MTK1.0" Active="Yes" DebugLevel="0" LanDebug="0" PMDebugLevel="0" Ready="start" ponDelay="15" AUTO_ID_ENABLE="0" macBridgePort1="0 0" macBridgePort2="0 1" macBridgePort3="0 2" macBridgePort4="0 3" macBridgePort5="0 0" macBridgePortffff="1 fff" macBridgePort6="1 f80" macBridgePort7="1 aa0" macBridgePort8="1 5a0" />
</OMCI>
<XPON>
<Common phyStatus="gpon_phy_up" trafficStatus="up" startXpon="No" CfgLoading="Done" xpon_up="0" Firstlogin="1" wanstatus="up" GponBindIfc="Yes" losStatus="up" upTime="6229" />
<LinkCfg Mode="1" LinkSta="1" OnuStatus="5" LoidAuthStatus="1" OnuID="32" />
<TR069/>
<VOICE/>
<IPHost1/>
<IPHost2/>
</XPON>
<SysInfo>
<Entry Vendor="TC" ProductName="HGW" SWVer="TCLinux Fw 7.1.2.7" FWVer="3.10.0.24" PubDate="2010/11/11" BatchNum="STC20P0.012.310024" SerialNum="1234" Description="" HWVer="HardWare Ver.0001" GateWay="Family GateWay" Model="HGW" IPForward_Flag="0" ResetFlag="0" />
</SysInfo>
<DefaultIp>
<Entry ip="192.168.1.1" gateway="" />
</DefaultIp>
<Sys>
<Entry IPProtocolVersion="3" Capability="2;4GE;1;3;5" />
</Sys>
<Lan>
<Dhcp type="1" />
<IgmpSnoop igmpsnoopEnable="Yes" />
<BridgeMacLimit macLimitPort1="1025" macLimitPort2="1025" macLimitPort3="1025" macLimitPort4="1025" />
<Stp Stpenable="Yes" Ageingtime="300" />
<Entry0 IP="192.168.1.1" netmask="255.255.255.0" IP6="fe80::6620:e1ff:fea3:eefa" PREFIX6="64" />
</Lan>
<Wan>
<Common ReConnect="1" LatestIFIdx="1" IPForwardModeEnable="No" isCT2PORTSSupported="Yes" DefaultBridge="1" />
<PVC0 Action="Modify" VLANID="100" DOT1P="0" VLANMode="TAG" ENCAP="PPPoE LLC" >
<Entry0 v8021PEnable="No" Active="Yes" ServiceList="TR069_INTERNET" BandActive="N/A" LAN1="Yes" LAN2="Yes" LAN3="Yes" LAN4="Yes" LAN25="Yes" SSID2="Yes" SSID3="Yes" SSID4="Yes" SSID5="Yes" SSIDAC2="Yes" SSIDAC3="Yes" SSIDAC4="No" SSIDAC5="Yes" WanMode="Route" LinkMode="linkPPP" MTU="1492" PPPGETIP="Dynamic" CONNECTION="Connect_Keep_Alive" USERNAME="9611668550@fiberhome" PASSWORD="password" SRVNAME="" PPPManualStatus="disconnect" IPVERSION="IPv4/IPv6" ISP="2" VLANMode="TAG" dot1q="Yes" VLANID="100" dot1p="Yes" dot1pData="0" DOT1P="0" MulticastVID="" NATENABLE="Enable" IGMPproxy="No" DHCPv6="No" GW6_Manual="No" IFIdx="1" DsliteEnable="No" DsliteMode="0" PDEnable="Yes" DHCPv6PD="Yes" PDOrigin="PrefixDelegation" DHCPEnable="1" BridgeInterface="" tr69_wanidx="1" tr69_entryidx="1" ConnectionError="ERROR_NONE" NASName="nas0_0" IFName="ppp0" GW_last="100.88.216.1" IP_last="100.88.219.222" uptime_sec="68" uptime_nsec="732945920" PDPrefix="2001:fb1:75:a0dc::/64" IP6_last="2001:fb1:fd0:71:e174:c9db:25ae:78ad" uptime6_sec="68" uptime6_nsec="75254880" TrueBr0Addr="2001:fb1:75:a0dc:6620:e1ff:fea3:eefa/64" TrueBr0IPv6HostAddr="2001:fb1:75:a0dc:6620:e1ff:fea3:eefa" />
</PVC0>
<PVC1 Action="Add" VLANID="293" DOT1P="0" VLANMode="TAG" ENCAP="1483 Bridged IP LLC" EPONEnable="Yes" GPONEnable="Yes" pvcindex="3" >
<Entry0 v8021PEnable="No" Active="Yes" ServiceList="INTERNET" BandActive="N/A" LAN1="No" LAN2="No" LAN3="No" LAN4="No" SSID2="No" SSID3="No" SSID4="No" SSID5="No" SSIDAC2="No" SSIDAC3="No" SSIDAC4="Yes" SSIDAC5="No" WanMode="Bridge" LinkMode="linkPPP" BridgeMode="IP_Bridged" DHCPRealy="Yes" IPVERSION="IPv4" ISP="3" VLANMode="TAG" dot1q="Yes" VLANID="293" dot1p="Yes" dot1pData="0" DOT1P="0" MulticastVID="" NATENABLE="Disabled" IGMPproxy="No" DHCPv6="No" GW6_Manual="No" IFIdx="2" DsliteEnable="No" PDEnable="No" DHCPv6PD="No" PDOrigin="None" DHCPEnable="0" BridgeInterface="" THSI="1" PPPManualStatus="disconnect" ConnectionError="ERROR_NO_ANSWER" NASName="nas1_0" IFName="nas1_0" uptime_sec="47" uptime_nsec="583208720" uptime6_sec="47" uptime6_nsec="583208720" />
</PVC1>
</Wan>
<Radvd>
<Entry PrefixIPv6="3ffe:501:ffff:100::" Prefixv6Len="64" Enable="1" Mode="0" ValidLifetime="7200" PreferredLifetime="3600" RAMOEnable="1" MinRAInterval="200" MaxRAInterval="600" AutoPrefix="0" DelegatedWanConnection="" ManagedEnable="0" OtherEnable="1" npt_wan_idx="" npt_wan_idx2="" />
</Radvd>
<Dhcp6s>
<Entry Enable="1" Mode="0" DNSserver="fe80::1" SecDNSserver="fe80::2" PreferredLifetime="3600" ValidLifetime="7200" DNSType="0" DNSWANConnection="0" />
<Option16/>
<Option17/>
</Dhcp6s> |
Beta Was this translation helpful? Give feedback.
0 replies
-
Your problem is plug SC/APC to SC/UPC, so loss fiber. |
Beta Was this translation helpful? Give feedback.
0 replies
-
|
Well I got an adapter and still same exact thing. I have root access on my ISPs ONT. I have the config file posted above. I can get an O5 status but only initial status with no ONU ID given to me by the ISP. And my PPP user/pass will not connect with the right vlan |
Beta Was this translation helpful? Give feedback.
0 replies
-
|
Anyone know what this is in my ISPs config?? EnhancedPSK="01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 00" |
Beta Was this translation helpful? Give feedback.
0 replies
-
|
This explains it. Looks like my ISP is using this as an auth key. Any firmware out there that supports this method of authentication for our SFP sticks? |
Beta Was this translation helpful? Give feedback.
1 reply
-
|
if you tell me, my ISP have D-Link DPN-FX3060V which is using Realtek RTL9607DQ (4 core ARM Cortex A55) thing is, Realtek SDK did not provide any the |
Beta Was this translation helpful? Give feedback.
-
|
I can provide the firmware for reverse engineering this enhanced PSK |
Beta Was this translation helpful? Give feedback.
1 reply
-
|
it would be nice if you can reverse engineering odi firmware to add enhanced PSK |
Beta Was this translation helpful? Give feedback.
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
-
I have changed ISPs due to a move. The new ISP provided GPON has both a "Material code" and a "True SN" in addition to a GPON SN and a Device SN (which match). I can't seem to get past an O3 status no matter what I try. The material code is 600001XXXX, and True SN (True is the name of the ISP) is 14281324240236XXXX if the digits give any advice to what it actually is used for.
Is there a way to see the logs of the HSGQ gpon stick and see where it is failing when trying to connect?
Beta Was this translation helpful? Give feedback.
All reactions