NetSNMP

NetSNMP v5.7

OSCAR does NOT require NetSNMP, but if you desire to translate Dotted OIDs to Textual OIDs you will need to install NetSNMP

Download NetSNMP Binaries for your OS

##Caveat

When using OSCAR for the first time with NetSNMP, there is a performance hit, a system call is required to the snmptranslate application for OID lookups. As each time you use OSCAR, a DB mapping of the Dotted-OID <=> Textual-OID is created, this will reduce the lookup time by by-passing snmptranslate.

This file is located in db/DottedTextualNetSNMPMap.json

---

DOCSIS & PacketCable MIBs

Unzip mibs.zip in the same install directory as oscar.jar

Review MIBS

####Dotted OID

Snmp11 1.3.6.1.2.1.69.1.2.1.2.1 IpAddress "0.0.0.0";

####Textual OID

Snmp11 docsDevNmAccessIp.1 IpAddress "0.0.0.0";

---

##Snmp11 vs. Snmp64

Snmp11 encodes a ASN.1 Basic Encoding Rule (BER) as part of a SNMP SET encapsulated using TLV Type 11. The total byte length is less than 256 or a TLV Length of 1 byte.

Snmp64 encodes a ASN.1 Basic Encoding Rule (BER) as part of a SNMP SET encapsulated using TLV Type 64. The total byte length is less than 65535 or a TLV Length of 2 bytes.

Typical Usage is reserved to PacketCable setting the DigitMap configuration

---

##Data Types Mapping of the SYNTAX clause

####Source: RFC-2578

####COUNTER32

The Counter32 type represents a non-negative integer which monotonically increases until it reaches a maximum value of 2^32-1 (4294967295 decimal), when it wraps around and starts increasing again from zero.

This is not a typical set for an OID

Syntax: Counter32

####COUNTER64

The Counter64 type represents a non-negative integer which monotonically increases until it reaches a maximum value of 2^64-1 (18446744073709551615 decimal), when it wraps around and starts increasing again from zero.

This is not a typical set for an OID

Syntax: Counter64

####GAUGE32

The Gauge32 type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value. The maximum value can not be greater than 2^32-1 (4294967295 decimal), and the minimum value can not be smaller than 0.

This is not a typical set for an OID

Syntax: Gauge32

####INTEGER and INTEGER32

The Integer32 type represents integer-valued information between -2^31 and 2^31-1 inclusive (-2147483648 to 2147483647 decimal). This type is indistinguishable from the INTEGER type. Both the INTEGER and Integer32 types may be sub-typed to be more constrained than the Integer32 type.

The INTEGER type (but not the Integer32 type) may also be used to represent integer-valued information as named-number enumerations. In this case, only those named-numbers so enumerated may be present as a value. Note that although it is recommended that enumerated values start at 1 and be numbered contiguously, any valid value for Integer32 is allowed for an enumerated value and, further, enumerated values needn't be contiguously assigned.

Snmp11 docsDevNmAccessControl.1 Integer "3";

Snmp11 docsDevNmAccessControl.1 Integer32 "3";

####TIMETICKS

This represents a non-negative integer which specifies the elapsed time between two events, in units of hundredth of a second. The range is 0 to 2e32 - 1

This is not a typical set for an OID

Syntax: TimeTicks

####IPADDRESS

The IpAddress type represents a 32-bit internet address. It is represented as an OCTET STRING of length 4, in network byte-order.

Snmp11 docsDevNmAccessIp.1 IpAddress "0.0.0.0";

####OCTETSTRING

The OCTET STRING type represents arbitrary binary or textual data. Although the SMI-specified size limitation for this type is 65535 octets, MIB designers should realize that there may be implementation and interoperability limitations for sizes in excess of 255 octets.

Snmp11 docsDevNmAccessCommunity.1 OctetString "ReadWrite";

####HEXSTRING

HexString is not a primitive datatype for SNMP, but it is used many time when the OID definition required a ByteArray representation of data

Snmp11 docsDevNmAccessInterfaces.1 HexString "40:00"

---

##Unsupported Syntax

####UNSIGNED32

The Unsigned32 type represents integer-valued information between 0 and 2^32-1 inclusive (0 to 4294967295 decimal).

Not Supported at this time

####OBJECT IDENTIFIER

The OBJECT IDENTIFIER type represents administratively assigned names. Any instance of this type may have at most 128 sub- identifiers. Further, each sub-identifier must not exceed the value 2^32-1 (4294967295 decimal).

Not Supported at this time

####OPAQUE

The Opaque type is provided solely for backward-compatibility, and shall not be used for newly-defined object types.

Not Supported at this time

---

###Syntax API

BERService