README.md

no-descending-specificity

Disallow selectors of lower specificity from coming after overriding selectors of higher specificity.

    #container a { top: 10px; } a { top: 0; }
/** ↑                           ↑
 * The order of these selectors represents descending specificity */

Source order is important in CSS, and when two selectors have the same specificity, the one that occurs last will take priority. However, the situation is different when one of the selectors has a higher specificity. In that case, source order does not matter: the selector with higher specificity will win out even if it comes first.

The clashes of these two mechanisms for prioritization, source order and specificity, can cause some confusion when reading stylesheets. If a selector with higher specificity comes before the selector it overrides, we have to think harder to understand it, because it violates the source order expectation. Stylesheets are most legible when overriding selectors always come after the selectors they override. That way both mechanisms, source order and specificity, work together nicely.

This rule enforces that practice as best it can, reporting fewer errors than it should. It cannot catch every actual overriding selector, but it can catch certain common mistakes.

We recommend turning this rule off if you use a lot of nesting.

How it works

This rule looks at the last compound selector in every full selector, and then compares it with other selectors in the stylesheet that end in the same way.

So .foo .bar (whose last compound selector is .bar) will be compared to .bar and #baz .bar, but not to #baz .foo or .bar .foo.

And a > li#wag.pit (whose last compound selector is li#wag.pit) will be compared to div li#wag.pit and a > b > li + li#wag.pit, but not to li or li #wag, etc.

Selectors targeting pseudo-elements are not considered comparable to similar selectors without the pseudo-element, because they target other elements on the rendered page. For example, a::before {} will not be compared to a:hover {}, because a::before targets a pseudo-element whereas a:hover targets the actual <a>.

This rule only compares rules that are within the same media context. So a {} @media print { #baz a {} } is fine.

This rule resolves nested selectors before calculating the specificity of the selectors.

DOM Limitations

The linter can only check the CSS to check for specificity order. It does not have access to the HTML or DOM in order to interpret the use of the CSS.

This can lead to valid linting errors appearing to be invalid at first glance.

For example the following will cause an error:

.component1 a {}
.component1 a:hover {}
.component2 a {}

This is a correct error because the a:hover on line 2 has a higher specificity than the a on line 3.

This may lead to confusion because "the two selectors will never match the same a in the DOM". However, since the linter does not have access to the DOM it can not evaluate this, and therefore correctly reports the error about descending specificity.

It may be possible to restructure your CSS to remove the error, otherwise it is recommended that you disable the rule for that line and leave a comment saying why the error should be ignored. Note that disabling the rule will cause additional valid errors from being reported.

Options

true

The following patterns are considered problems:

b a {}
a {}

a + a {}
a {}

b > a[foo] {}
a[foo] {}

a {
  & > b {}
}
b {}

@media print {
  #c a {}
  a {}
}

The following patterns are not considered problems:

a {}
b a {}

a {}
a + a {}

a[foo] {}
b > a[foo] {}

b {}
a {
  & > b {}
}

a::before {}
a:hover::before {}
a {}
a:hover {}

@media print {
  a {}
  #c a {}
}

a {}
@media print {
  #baz a {}
}

Optional secondary options

ignore: ["selectors-within-list"]

Ignores selectors within list of selectors.

The following patterns are considered problems:

b a {}
h1 {}
h2 {}
h3 {}
a {}

The following patterns are not considered problems:

b a {}
h1, h2, h3, a {}