This example demonstrates the use of the SPI serial communication block (SCB) resource for Infineon MCU in master and slave mode using DMA. The SPI master is configured to send command packets to control a user LED on the slave. Both the master and slave can be on the same device or on different devices.
Provide feedback on this code example.
- ModusToolbox™ v3.1 or later (tested with v3.3)
- Programming language: C
- Associated parts: XMC7000 MCU, TRAVEO™ T2G Body High MCU
- GNU Arm® Embedded Compiler v11.3.1 (
GCC_ARM) – Default value ofTOOLCHAIN - Arm® Compiler v6.22 (
ARM) - IAR C/C++ Compiler v9.50.2 (
IAR)
- XMC7200 Evaluation Kit (
KIT_XMC72_EVK) – Default value ofTARGET - TRAVEO™ T2G Body High Evaluation Kit (
KIT_T2G-B-H_EVK) - XMC7100 Evaluation Kit (
KIT_XMC71_EVK_LITE_V1) - XMC7200 Evaluation Kit (
KIT_XMC72_EVK_MUR_43439M2)
This example uses the board's default configuration. See the kit user guide to ensure that the board is configured correctly.
Use jumper wires to establish a connection between the master and slave on the kit. For the default kit, do the following on the board (verify with the corresponding custom design.modus file to find the respective SPI pins for other kits).
XMC7200 Evaluation Kit:
- Connect P12[0] to P14[0].
- Connect P12[1] to P14[1].
- Connect P12[2] to P14[2].
- Connect P12[3] to P14[3].
XMC7100 Evaluation Kit:
- Connect P13[0] to P14[0].
- Connect P13[1] to P14[1].
- Connect P13[2] to P14[2].
- Connect P13[3] to P14[3].
See the ModusToolbox™ tools package installation guide for information about installing and configuring the tools package.
This example requires no additional software or tools.
The ModusToolbox™ tools package provides the Project Creator as both a GUI tool and a command line tool.
Use Project Creator GUI
-
Open the Project Creator GUI tool.
There are several ways to do this, including launching it from the dashboard or from inside the Eclipse IDE. For more details, see the Project Creator user guide (locally available at {ModusToolbox™ install directory}/tools_{version}/project-creator/docs/project-creator.pdf).
-
On the Choose Board Support Package (BSP) page, select a kit supported by this code example. See Supported kits.
Note: To use this code example for a kit not listed here, you may need to update the source files. If the kit does not have the required resources, the application may not work.
-
On the Select Application page:
a. Select the Applications(s) Root Path and the Target IDE.
Note: Depending on how you open the Project Creator tool, these fields may be pre-selected for you.
b. Select this code example from the list by enabling its check box.
Note: You can narrow the list of displayed examples by typing in the filter box.
c. (Optional) Change the suggested New Application Name and New BSP Name.
d. Click Create to complete the application creation process.
Use Project Creator CLI
The 'project-creator-cli' tool can be used to create applications from a CLI terminal or from within batch files or shell scripts. This tool is available in the {ModusToolbox™ install directory}/tools_{version}/project-creator/ directory.
Use a CLI terminal to invoke the 'project-creator-cli' tool. On Windows, use the command-line 'modus-shell' program provided in the ModusToolbox™ installation instead of a standard Windows command-line application. This shell provides access to all ModusToolbox™ tools. You can access it by typing "modus-shell" in the search box in the Windows menu. In Linux and macOS, you can use any terminal application.
The following example clones the "mtb-example-pdl-xmc7000-spi-master-dma" application with the desired name "PdlScbMasterDma" configured for the KIT_XMC72_EVK BSP into the specified working directory, C:/mtb_projects:
project-creator-cli --board-id KIT_XMC72_EVK --app-id mtb-example-pdl-xmc7000-spi-master-dma --user-app-name PdlScbMasterDma --target-dir "C:/mtb_projects"
The 'project-creator-cli' tool has the following arguments:
| Argument | Description | Required/optional |
|---|---|---|
--board-id |
Defined in the field of the BSP manifest | Required |
--app-id |
Defined in the field of the CE manifest | Required |
--target-dir |
Specify the directory in which the application is to be created if you prefer not to use the default current working directory | Optional |
--user-app-name |
Specify the name of the application if you prefer to have a name other than the example's default name | Optional |
Note: The project-creator-cli tool uses the
git cloneandmake getlibscommands to fetch the repository and import the required libraries. For details, see the "Project creator tools" section of the ModusToolbox™ tools package user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mtb_user_guide.pdf).
After the project has been created, you can open it in your preferred development environment.
Eclipse IDE
If you opened the Project Creator tool from the included Eclipse IDE, the project will open in Eclipse automatically.
For more details, see the Eclipse IDE for ModusToolbox™ user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mt_ide_user_guide.pdf).
Visual Studio (VS) Code
Launch VS Code manually, and then open the generated {project-name}.code-workspace file located in the project directory.
For more details, see the Visual Studio Code for ModusToolbox™ user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mt_vscode_user_guide.pdf).
Keil µVision
Double-click the generated {project-name}.cprj file to launch the Keil µVision IDE.
For more details, see the Keil µVision for ModusToolbox™ user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mt_uvision_user_guide.pdf).
IAR Embedded Workbench
Open IAR Embedded Workbench manually, and create a new project. Then select the generated {project-name}.ipcf file located in the project directory.
For more details, see the IAR Embedded Workbench for ModusToolbox™ user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mt_iar_user_guide.pdf).
Command line
If you prefer to use the CLI, open the appropriate terminal, and navigate to the project directory. On Windows, use the command-line 'modus-shell' program; on Linux and macOS, you can use any terminal application. From there, you can run various make commands.
For more details, see the ModusToolbox™ tools package user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mtb_user_guide.pdf).
-
Connect the board to your PC using the provided USB cable through the KitProg3 USB connector.
-
Configure the value of the
SPI_MODEmacro in interface.h toSPI_MODE_BOTH(only for kits with two SPI ports). -
Program the board using one of the following:
Using Eclipse IDE
-
Select the application project in the Project Explorer.
-
In the Quick Panel, scroll down, and click <Application Name> Program (KitProg3_MiniProg4).
In other IDEs
Follow the instructions in your preferred IDE.
Using CLI
From the terminal, execute the
make programcommand to build and program the application using the default toolchain to the default target. The default toolchain is specified in the application's Makefile but you can override this value manually:make program TOOLCHAIN=<toolchain>Example:
make program TOOLCHAIN=GCC_ARM -
-
After programming, the application starts automatically. Observe that the kit LED blinks at 1 Hz.
By default, the kit is configured to work in both master and slave mode (ensure that the SPI_MODE macro in interface.h is configured as SPI_MODE_BOTH).
Do the following to configure the kit to work in both master and slave mode:
-
Run the Device configurator tool from the Quick Panel of the IDE.
Because the kit has only one available SPI port, by default, the associated SCB is aliased as mSPI in the Peripherals tab.
-
Rename the associated SCBs to sSPI and mSPI and configure the SCBs:
Figure 1. Configure peripherals master SPI
Figure 2. Configure peripherals slave SPI
-
In the Pins tab, assign the correct drive mode to SPI pins in the Drive Mode dropdown menu:
Table 1. Drive mode for slave SPI pins
SPI pins Drive mode MOSI Digital High-Z. Input buffer ON MISO Strong Drive. Input buffer OFF SCLK Digital High-Z. Input buffer ON SS0 Digital High-Z. Input buffer ON
Table 2. Drive mode for master SPI pins
SPI pins Drive mode MOSI Strong Drive. Input buffer OFF MISO Digital High-Z. Input buffer ON SCLK Strong Drive. Input buffer OFF SS0 Strong Drive. Input buffer OFF
-
In the DMA tab, rename the DMA to txDma and rxDma and configure it:
Figure 3. Configure txDMA
Figure 4. Configure rxDMA
-
Select File > Save to save the changes and generate the configuration files.
You can debug the example to step through the code.
In Eclipse IDE
Use the <Application Name> Debug (KitProg3_MiniProg4) configuration in the Quick Panel. For details, see the "Program and debug" section in the Eclipse IDE for ModusToolbox™ user guide.
In other IDEs
Follow the instructions in your preferred IDE.
The following table lists the resources used in this example and their purpose.
Table 1. Application resources
| Resource | Alias/object | Purpose |
|---|---|---|
| SCB (SPI) | mSPI | Master SPI SCB |
| SCB (SPI) | sSPI | Slave SPI SCB |
| GPIO | CYBSP_USER_LED | LED indication |
| DMA | txDma | Data transfer |
| DMA | rxDma | Data transfer |
| Resources | Links |
|---|---|
| Application notes | AN234334 – Getting started with XMC7000 MCU on ModusToolbox™ software AN234021 – Low-power mode procedure in XMC7000 family |
| Code examples | Using ModusToolbox™ on GitHub |
| Device documentation | XMC7000 MCU documents |
| Development kits | Select your kits from the Evaluation board finder. |
| Libraries on GitHub | mtb-pdl-cat1 – Peripheral Driver Library (PDL) mtb-hal-cat1 – Hardware Abstraction Layer (HAL) library retarget-io – Utility library to retarget STDIO messages to a UART port |
| Middleware on GitHub | mcu-middleware – Links to all MCU middleware |
| Tools | ModusToolbox™ – ModusToolbox™ software is a collection of easy-to-use libraries and tools enabling rapid development with Infineon MCUs for applications ranging from wireless and cloud-connected systems, edge AI/ML, embedded sense and control, to wired USB connectivity using PSOC™ Industrial/IoT MCUs, AIROC™ Wi-Fi and Bluetooth® connectivity devices, XMC™ Industrial MCUs, and EZ-USB™/EZ-PD™ wired connectivity controllers. ModusToolbox™ incorporates a comprehensive set of BSPs, HAL, libraries, configuration tools, and provides support for industry-standard IDEs to fast-track your embedded application development. |
Infineon provides a wealth of data at www.infineon.com to help you select the right device, and quickly and effectively integrate it into your design.
For XMC™ MCU devices, see 32-bit XMC™ industrial microcontroller based on Arm® Cortex®-M.
Document title: CE233860 – XMC7000 MCU: SCB SPI master with DMA
| Version | Description of change |
|---|---|
| 1.0.0 | New code example |
| 1.1.0 | Added support for KIT_T2G-B-H_EVK |
| 1.2.0 | Updated for clock setting of KIT_XMC72_EVK |
| 2.0.0 | Updated to support ModusToolbox™ v3.1 and added support for the BSP KIT_XMC71_EVK_LITE_V1 |
| 2.1.0 | Added support for KIT_XMC72_EVK_MUR_43439M2 |
| 2.1.1 | Disabled D-cache for XMC7000 based BSPs |
| 2.2.0 | Enabled D-cache support for XMC7000 devices |
All referenced product or service names and trademarks are the property of their respective owners.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by Infineon is under license.
© Cypress Semiconductor Corporation, 2022-2024. This document is the property of Cypress Semiconductor Corporation, an Infineon Technologies company, and its affiliates ("Cypress"). This document, including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No computing device can be absolutely secure. Therefore, despite security measures implemented in Cypress hardware or software products, Cypress shall have no liability arising out of any security breach, such as unauthorized access to or use of a Cypress product. CYPRESS DOES NOT REPRESENT, WARRANT, OR GUARANTEE THAT CYPRESS PRODUCTS, OR SYSTEMS CREATED USING CYPRESS PRODUCTS, WILL BE FREE FROM CORRUPTION, ATTACK, VIRUSES, INTERFERENCE, HACKING, DATA LOSS OR THEFT, OR OTHER SECURITY INTRUSION (collectively, "Security Breach"). Cypress disclaims any liability relating to any Security Breach, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any Security Breach. In addition, the products described in these materials may contain design defects or errors known as errata which may cause the product to deviate from published specifications. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. "High-Risk Device" means any device or system whose failure could cause personal injury, death, or property damage. Examples of High-Risk Devices are weapons, nuclear installations, surgical implants, and other medical devices. "Critical Component" means any component of a High-Risk Device whose failure to perform can be reasonably expected to cause, directly or indirectly, the failure of the High-Risk Device, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any use of a Cypress product as a Critical Component in a High-Risk Device. You shall indemnify and hold Cypress, including its affiliates, and its directors, officers, employees, agents, distributors, and assigns harmless from and against all claims, costs, damages, and expenses, arising out of any claim, including claims for product liability, personal injury or death, or property damage arising from any use of a Cypress product as a Critical Component in a High-Risk Device. Cypress products are not intended or authorized for use as a Critical Component in any High-Risk Device except to the limited extent that (i) Cypress's published data sheet for the product explicitly states Cypress has qualified the product for use in a specific High-Risk Device, or (ii) Cypress has given you advance written authorization to use the product as a Critical Component in the specific High-Risk Device and you have signed a separate indemnification agreement.
Cypress, the Cypress logo, and combinations thereof, ModusToolbox, PSoC, CAPSENSE, EZ-USB, F-RAM, and TRAVEO are trademarks or registered trademarks of Cypress or a subsidiary of Cypress in the United States or in other countries. For a more complete list of Cypress trademarks, visit www.infineon.com. Other names and brands may be claimed as property of their respective owners.