What is this ?

Simulate Wi-Fi (802.11) between Linux Virtual Machines on Qemu/VirtualBox/...

• It can be used in Hypervisors (GNS3, QEmu, Virtualbox, VMware, Hyper-V, ...)

• The Wireless emulator uses the mac80211_hwsim linux driver

• Implements the packet loss simulation based on distance

• Emulates the node mobility in GNS3

• Tested:

  • with hostapd and wpa_supplicant with these configurations:
    • Open
    • WEP
    • WPA2
    • WPA-EAP
  • in the context of WPA2 attack with Aircrack-NG (Kali / Parrot-OS)
  • with OpenWRT

• Remaining features to be implemented:

  • Integrate to other OS (Windows...)
  • Add obstacle models
  • Etc.

Explanations

• With the parameter "-h" (or "--help"), all programs display help and their parameters

• vwifi-client should be started on the VMs, and vwifi-server on the Host.

• vwifi-client and vwifi-server can communicate either with the VHOST protocol (by default), or with the TCP protocol.

• With the option "-s" (or "--spy"), vwifi-client :

  • receives always all communications, even if the loss of packets is enable ;
  • works only with TCP ;
  • connects to 127.0.0.1, by default ;

• vwifi-client uses the mac80211_hwsim kernel module to have the wifi interfaces.

• To use TCP protocol, vwifi-server and vwifi-client must be connected to a different IP network than that of the wifi.

• vwifi-add-interfaces is used to create the wlan interfaces to the module mac80211_hwsim. vwifi-client controls only these interfaces. vwifi-add-interfaces can be run several times.

• vwifi-ctrl is used to interact with vwifi-server.

• vwifi-server can directly enable packet loss with the parameter "-l" (or "--lost-packets")

• If vwifi-server detects the same IP for several vwifi-client (due to PAT/NPAT/...), use the option "-u" ("-- use-port-in-hash") on vwifi-server to add the network port to create the ID for each client, instead of just using the IP. Attention, the display of ID by vwifi-server and vwifi-client will no longer be the same.

• You can change the defaults IP and ports with parameters (see the parameter "-h" to help)

Install

On Debian-based Linux distributions

Dependencies

sudo apt-get install make g++
sudo apt-get install libnl-3-dev libnl-genl-3-dev

Building

• Not necessary :

make gitversion # To add the last commit id to the VERSION

make update # To download and update the file mac80211_hwsim.h

• To change the default ports and IP, edit : src/config.h

• To building :

make
make tools # To change the file mode bits of tools

sudo make install

On OpenWRT

• See the wiki : Install-vwifi-on-OpenWRT-X86_64

Configuration

Method 1 : With VHOST

Host

• Shell :

  • Load the module VHOST :

  # sudo modprobe -r vhost_vsock vmw_vsock_virtio_transport_common vsock # if necessary
  
  sudo modprobe vhost_vsock
  sudo chmod a+rw /dev/vhost-vsock

  • Start the vwifi-server :

  vwifi-server

• Hypervisor

  • QEmu : add the option : -device vhost-vsock-pci,id=vwifi0,guest-cid=NUM with NUM an identifier greater than 2
  • GNS3 (>= 2.2) : QEmu : add the option : -device vhost-vsock-pci,id=vwifi0,guest-cid=%guest-cid%

Each Guest

• Load the necessary module mac80211_hwsim with 0 radios :

sudo modprobe mac80211_hwsim radios=0

• Create the wlan interfaces (on this example, 2 interfaces) :
  • Without parameters, the MAC address is preset with the default value "74:F8:F6", and the 4th byte is randomized
  • vwifi-client can do the same with the parameters "--number" and "--mac"

sudo vwifi-add-interfaces 2 0a:0b:0c:03:02

• Connect all these wlan interfaces to the vwifi-server :

sudo vwifi-client

• vwifi-client displays the CID of the VM in the Hypervisor. It is used by vwifi-server to identify this guest.

Method 2 : With TCP

• vwifi-server and vwifi-client must be connected to a different IP network than that of the wifi (for example : 172.16.0.0/16)

Host

• Start the vwifi-server :

vwifi-server

• We will suppose that the Host have the IP address : 172.16.0.1

Each Guest

• Load the necessary module mac80211_hwsim with 0 radios :

sudo modprobe mac80211_hwsim radios=0

• Create the wlan interfaces (on this example, 2 interfaces) :
  • Without parameters, the MAC address is preset with the default value "74:F8:F6", and the 4th byte is randomized
  • vwifi-client can do the same with the parameters "--number" and "--mac"

sudo vwifi-add-interfaces 2 0a:0b:0c:03:02

• Connect all these wlan interfaces to the vwifi-server :

sudo vwifi-client 172.16.0.1

• vwifi-client displays an ID which is an hashsum of the IP. It is used by vwifi-server to identify this guest.

Capture packets from Host

Configure the Spy

sudo modprobe mac80211_hwsim radios=0
sudo vwifi-client -s -n 1

Capture

• Configure wlan0 to monitor mode :

sudo ip link set wlan0 down
sudo iw wlan0 set monitor control
sudo ip link set wlan0 up

With tcpdump

• Capture from wlan0 :

sudo tcpdump -n -i wlan0

With wireshark

• Start Wireshark and capture from wlan0 :

sudo wireshark

Control

Host

• Show the list of connected guest (display : cid and coordinate x, y z) :

vwifi-ctrl ls

• Set the new coordinate (11, 12, 13) of the guest with the cid 10 :

vwifi-ctrl set 10 11 12 13

• Set the name "AP" of the guest with the cid 10 :

vwifi-ctrl setname 10 AP

• Enable the lost of packets :

vwifi-ctrl loss yes

• Disable the lost of packets :

vwifi-ctrl loss no

• Display the config of vwifi-server :

vwifi-ctrl status

• Display the distance in meters between the guest with the cid 10 and the guest with the cid 20 :

vwifi-ctrl distance 10 20

• Set the scale of the distances between the clients to 0.005

vwifi-ctrl scale 0.005

Examples of commands to test Wifi

Test 1 : WPA

Packages needed on the guests for this test

sudo apt install hostapd wpasupplicant

Guests

• Guest Wifi 1 :

sudo ip a a 10.0.0.1/8 dev wlan0

sudo hostapd tests/hostapd_wpa.conf

• Guest Wifi 2 :

sudo wpa_supplicant -Dnl80211 -iwlan0 -c tests/wpa_supplicant.conf

sudo ip a a 10.0.0.2/8 dev wlan0
ping 10.0.0.1

• Guest Wifi 3 :

sudo wpa_supplicant -Dnl80211 -iwlan0 -c tests/wpa_supplicant.conf

sudo ip a a 10.0.0.3/8 dev wlan0
ping 10.0.0.2

Test 2 : Open

Packages needed on the guests for this test

sudo apt install hostapd iw tcpdump

Guests

• Guest Wifi 1 :

sudo ip a a 10.0.0.1/8 dev wlan0

sudo hostapd tests/hostapd_open.conf

• Guest Wifi 2 :

sudo ip link set up wlan0
sudo iw dev wlan0 connect mac80211_open

sudo ip a a 10.0.0.2/8 dev wlan0
ping 10.0.0.1

• Guest Wifi 3 :

sudo ip link set up wlan0
sudo tcpdump -n -e -I -i wlan0 -w /hosthome/projects/vwifi_capture_wlan0.pcap

Host

tail -f -c +0b /home/user/projects/vwifi_capture_wlan0.pcap | wireshark -k -i -

Test 3 : Ad-Hoc

Packages needed on the guests for this test

sudo apt install iw

Guests

• Guest Wifi 1 :

sudo ip link set up wlan0
sudo iw wlan0 set type ibss
sudo iw wlan0 ibss join MYNETWORK 2412 # frequency 2412 is channel 1

sudo ip a a 10.0.0.1/8 dev wlan0

• Guest Wifi 2 :

sudo ip link set up wlan0
sudo iw wlan0 set type ibss
sudo iw wlan0 ibss join MYNETWORK 2412 # frequency 2412 is channel 1

sudo ip a a 10.0.0.2/8 dev wlan0
ping 10.0.0.1

Test 4 : WEP

Packages needed on the guests for this test

sudo apt install hostapd

Guests

• Guest Wifi 1 :

sudo ip a a 10.0.0.1/8 dev wlan0

sudo hostapd tests/hostapd_wep.conf

• Guest Wifi 2 :

cat << EOF | sudo tee -a /etc/network/interfaces > /dev/null

iface wlan0 inet static
    wireless-essid AP_WEP
    wireless-key s:12345
    address 10.0.0.2
    netmask 255.255.255.0

EOF
sudo ifup wlan0

ping 10.0.0.1

Others Tools

• start-vwifi-client.sh : do all the commands necessary to start vwifi-client on a Guest
• fast-vwifi-update.sh : set with vwifi-ctrl the coordinates of each VMs which has the option guest-cid=, found in the open project of GNS3
• client.sh : configure the client wifi with Open or WPA
• Makefile.dependency.sh : generate automatically the file "Makefile.in", include in "Makefile", which contains dependencies for "make"