An open source firmware for DSO-138 Oscilloscope.
DSO-138 is an excellent piece of hardware based on ARM Cortex M3 core STM32F103 processor and sufficient for most beginner users. The stock firmware, while quite responsive, can use a few improvements. The main shortcoming which prompted the development of DLO-138 firmware is the inability to get waveform data into a computer for further analysis and the lack of a second channel. Engineers troubleshooting hardware issues need to mark reference points on waveform so having another analog or digital channel can greatly improve analysis. This firmware hopes to improve on these issues.
- Two analog channels
- Two digital logic channels (SWDIO and SWDIO pins (PA13 and PA14) on board)
- Serial port interface for captured waveform data
- Trigger source selectable from Analog Channel 1 or Digital Channel
- Option to use rotary encoder instead of + - and SEL switches
- 2K sample depth
This firmware can be used on stock DSO-138 hardware as well. Select one of the pre-compiled binaries to suit the board. Follow the firmware upgrade instructions for DSO-138. At any time, you can reflash DSO-138 with JYE Tech provided firmware.
Extra features come at an additional cost. In the case of DLO-138, it is the loss of lowest timebase. Maximum sampling rate in DLO-138 is 20 µs/div instead of 10 µs/div. In the 20 µs/div range, firmware under-samples ADC channels, often reading same data twice. To use the second analog channel, analog front end has to be duplicated on a daughter board. On a stock hardware, this firmware can be used to provide two digital logic channels.
The build environment uses Arduino. For help with setting up IDE visit http://www.stm32duino.com
For graphics output, this project depends on the Adafruit GFX Library v1.1.4. Install it via the Library Manager of your Arduino IDE. Other/newer versions of this library are likely to not compile or will give you a black screen.
Following changes can be applied selectively, to get maximum functionality from board. The firmware can be run on unmodified hardware as well.
Push button in encoder (SEL if using switches) moves focus to next parameter
Left/Right turn in encoder (+/- if using switches) changes the parameter which is in focus
Short press OK to HOLD the waveform and output it on serial port
Long press OK button:
Focus Action
Trigger Level Zero the trigger level to Analog channel 1
Wave X scrollbar Center waveform on screen (at trigger point)
Wave Y cursor Zero the cursor. If Analog CH1 coupling is GND, waveform reference base is set
Other Toggle on screen Analog CH1 statistics display
Press and hold OK button at power up to reset settings to default
When using Windows you can follow the guide from jyetech: https://jyetech.com/wp-content/uploads/2018/07/dso138-firmware-upgrade.pdf
The guide uses the graphical programming tool provided by ST: https://www.st.com/en/development-tools/flasher-stm32.html
When using Linux, you can use the open source command line tool stm32flash:
Install stm32flash:
sudo apt-get install stm32flash
Connect your TTL-UART-to-USB converter to the DSO138 and bridge jumpers J1 and J2 on the back of the PCB just like in the above manual.
Unlock the flash of the STM32:
sudo stm32flash /dev/ttyUSB0 -k -b 115200
sudo stm32flash /dev/ttyUSB0 -u -b 115200
Flash new firmware:
sudo stm32flash /dev/ttyUSB0 -w binaries/DLO-138_switches_1.0.bin -b 115200
Remove the solder bridges on J1 and J2 and enjoy the alternative firmware on your DSO138.
DSO-138 - http://www.jyetech.com/Products/LcdScope/e138.php
STM32Duino - http://www.stm32duino.com
STM32F103 - http://www.st.com/en/microcontrollers/stm32f103.html
Adafruint Graphics Library - https://github.com/adafruit/Adafruit-GFX-Library
Parallel 8 bit ILI9341 library - https://github.com/stevstrong/Adafruit_TFTLCD_8bit_STM32
