diff --git a/CMakeLists.txt b/CMakeLists.txt index b6478aa16a3..1c8af639695 100644 --- a/CMakeLists.txt +++ b/CMakeLists.txt @@ -278,6 +278,10 @@ set(ARDUINO_LIBRARY_Zigbee_SRCS libraries/Zigbee/src/ep/ZigbeeSwitch.cpp libraries/Zigbee/src/ep/ZigbeeTempSensor.cpp libraries/Zigbee/src/ep/ZigbeeThermostat.cpp + libraries/Zigbee/src/ep/ZigbeeFlowSensor.cpp + libraries/Zigbee/src/ep/ZigbeePressureSensor.cpp + libraries/Zigbee/src/ep/ZigbeeOccupancySensor.cpp + libraries/Zigbee/src/ep/ZigbeeCarbonDioxideSensor.cpp ) set(ARDUINO_LIBRARY_BLE_SRCS diff --git a/libraries/Zigbee/examples/Zigbee_CarbonDioxide_Sensor/README.md b/libraries/Zigbee/examples/Zigbee_CarbonDioxide_Sensor/README.md new file mode 100644 index 00000000000..88c8bf04a65 --- /dev/null +++ b/libraries/Zigbee/examples/Zigbee_CarbonDioxide_Sensor/README.md @@ -0,0 +1,72 @@ +# Arduino-ESP32 Carbon dioxide (CO2) Sensor Example + +This example shows how to configure the Zigbee end device and use it as a Home Automation (HA) simple sensor device type with carbon dioxide measuring. + +# Supported Targets + +Currently, this example supports the following targets. + +| Supported Targets | ESP32-C6 | ESP32-H2 | +| ----------------- | -------- | -------- | + +## Pressure + Flow Sensor Functions + + * After this board first starts up, it would be configured locally to report the carbon dioxide on every 30 seconds. + * By clicking the button (BOOT) on this board, this board will immediately send a report of the current measured carbon dioxide to the network. + +## Hardware Required + +* A USB cable for power supply and programming + +### Configure the Project + +In this example, the internal temperature sensor is used to demonstrate reading of the carbon dioxide sensors. +Set the Button GPIO by changing the `button` variable. By default, it's the pin `BOOT_PIN` (BOOT button on ESP32-C6 and ESP32-H2). + +#### Using Arduino IDE + +To get more information about the Espressif boards see [Espressif Development Kits](https://www.espressif.com/en/products/devkits). + +* Before Compile/Verify, select the correct board: `Tools -> Board`. +* Select the End device Zigbee mode: `Tools -> Zigbee mode: Zigbee ED (end device)` +* Select Partition Scheme for Zigbee: `Tools -> Partition Scheme: Zigbee 4MB with spiffs` +* Select the COM port: `Tools -> Port: xxx` where the `xxx` is the detected COM port. +* Optional: Set debug level to verbose to see all logs from Zigbee stack: `Tools -> Core Debug Level: Verbose`. + +## Troubleshooting + +If the End device flashed with this example is not connecting to the coordinator, erase the flash of the End device before flashing the example to the board. It is recommended to do this if you re-flash the coordinator. +You can do the following: + +* In the Arduino IDE go to the Tools menu and set `Erase All Flash Before Sketch Upload` to `Enabled`. +* Add to the sketch `Zigbee.factoryReset();` to reset the device and Zigbee stack. + +By default, the coordinator network is closed after rebooting or flashing new firmware. +To open the network you have 2 options: + +* Open network after reboot by setting `Zigbee.setRebootOpenNetwork(time);` before calling `Zigbee.begin();`. +* In application you can anytime call `Zigbee.openNetwork(time);` to open the network for devices to join. + +***Important: Make sure you are using a good quality USB cable and that you have a reliable power source*** + +* **LED not blinking:** Check the wiring connection and the IO selection. +* **Programming Fail:** If the programming/flash procedure fails, try reducing the serial connection speed. +* **COM port not detected:** Check the USB cable and the USB to Serial driver installation. + +If the error persists, you can ask for help at the official [ESP32 forum](https://esp32.com) or see [Contribute](#contribute). + +## Contribute + +To know how to contribute to this project, see [How to contribute.](https://github.com/espressif/arduino-esp32/blob/master/CONTRIBUTING.rst) + +If you have any **feedback** or **issue** to report on this example/library, please open an issue or fix it by creating a new PR. Contributions are more than welcome! + +Before creating a new issue, be sure to try Troubleshooting and check if the same issue was already created by someone else. + +## Resources + +* Official ESP32 Forum: [Link](https://esp32.com) +* Arduino-ESP32 Official Repository: [espressif/arduino-esp32](https://github.com/espressif/arduino-esp32) +* ESP32-C6 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32-c6_datasheet_en.pdf) +* ESP32-H2 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32-h2_datasheet_en.pdf) +* Official ESP-IDF documentation: [ESP-IDF](https://idf.espressif.com) diff --git a/libraries/Zigbee/examples/Zigbee_CarbonDioxide_Sensor/Zigbee_CarbonDioxide_Sensor.ino b/libraries/Zigbee/examples/Zigbee_CarbonDioxide_Sensor/Zigbee_CarbonDioxide_Sensor.ino new file mode 100644 index 00000000000..47b9a05493f --- /dev/null +++ b/libraries/Zigbee/examples/Zigbee_CarbonDioxide_Sensor/Zigbee_CarbonDioxide_Sensor.ino @@ -0,0 +1,106 @@ +// Copyright 2024 Espressif Systems (Shanghai) PTE LTD +// +// Licensed under the Apache License, Version 2.0 (the "License"); +// you may not use this file except in compliance with the License. +// You may obtain a copy of the License at +// +// http://www.apache.org/licenses/LICENSE-2.0 +// +// Unless required by applicable law or agreed to in writing, software +// distributed under the License is distributed on an "AS IS" BASIS, +// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +// See the License for the specific language governing permissions and +// limitations under the License. + +/** + * @brief This example demonstrates Zigbee carbon dioxide sensor. + * + * The example demonstrates how to use Zigbee library to create a end device carbon dioxide sensor. + * + * Proper Zigbee mode must be selected in Tools->Zigbee mode + * and also the correct partition scheme must be selected in Tools->Partition Scheme. + * + * Please check the README.md for instructions and more detailed description. + * + * Created by Jan Procházka (https://github.com/P-R-O-C-H-Y/) + */ + +#ifndef ZIGBEE_MODE_ED +#error "Zigbee end device mode is not selected in Tools->Zigbee mode" +#endif + +#include "Zigbee.h" + +/* Zigbee carbon dioxide sensor configuration */ +#define CARBON_DIOXIDE_SENSOR_ENDPOINT_NUMBER 10 +uint8_t button = BOOT_PIN; + +ZigbeeCarbonDioxideSensor zbCarbonDioxideSensor = ZigbeeCarbonDioxideSensor(CARBON_DIOXIDE_SENSOR_ENDPOINT_NUMBER); + +void setup() { + Serial.begin(115200); + + // Init button switch + pinMode(button, INPUT_PULLUP); + + // Optional: set Zigbee device name and model + zbCarbonDioxideSensor.setManufacturerAndModel("Espressif", "ZigbeeCarbonDioxideSensor"); + + // Set minimum and maximum carbon dioxide measurement value in ppm + zbCarbonDioxideSensor.setMinMaxValue(0, 1500); + + // Add endpoints to Zigbee Core + Zigbee.addEndpoint(&zbCarbonDioxideSensor); + + Serial.println("Starting Zigbee..."); + // When all EPs are registered, start Zigbee in End Device mode + if (!Zigbee.begin()) { + Serial.println("Zigbee failed to start!"); + Serial.println("Rebooting..."); + ESP.restart(); + } else { + Serial.println("Zigbee started successfully!"); + } + Serial.println("Connecting to network"); + while (!Zigbee.connected()) { + Serial.print("."); + delay(100); + } + Serial.println(); + + // Set reporting interval for carbon dioxide measurement to be done every 30 seconds, must be called after Zigbee.begin() + // min_interval and max_interval in seconds, delta (carbon dioxide change in ppm) + // if min = 1 and max = 0, reporting is sent only when carbon dioxide changes by delta + // if min = 0 and max = 10, reporting is sent every 10 seconds or when carbon dioxide changes by delta + // if min = 0, max = 10 and delta = 0, reporting is sent every 10 seconds regardless of delta change + zbCarbonDioxideSensor.setReporting(0, 30, 0); +} + +void loop() { + static uint32_t timeCounter = 0; + // Read carbon dioxide sensor every 2s + if (!(timeCounter++ % 20)) { // delaying for 100ms x 20 = 2s + // Read sensor value - here is chip temperature used + 300 as a dummy value for demonstration + uint16_t carbon_dioxide_value = 300 + (uint16_t)temperatureRead(); + Serial.printf("Updating carbon dioxide sensor value to %d ppm\r\n", carbon_dioxide_value); + zbCarbonDioxideSensor.setCarbonDioxide(carbon_dioxide_value); + } + + // Checking button for factory reset and reporting + if (digitalRead(button) == LOW) { // Push button pressed + // Key debounce handling + delay(100); + int startTime = millis(); + while (digitalRead(button) == LOW) { + delay(50); + if ((millis() - startTime) > 3000) { + // If key pressed for more than 3secs, factory reset Zigbee and reboot + Serial.println("Resetting Zigbee to factory and rebooting in 1s."); + delay(1000); + Zigbee.factoryReset(); + } + } + zbCarbonDioxideSensor.report(); + } + delay(100); +} diff --git a/libraries/Zigbee/examples/Zigbee_CarbonDioxide_Sensor/ci.json b/libraries/Zigbee/examples/Zigbee_CarbonDioxide_Sensor/ci.json new file mode 100644 index 00000000000..7b7ccef8ed7 --- /dev/null +++ b/libraries/Zigbee/examples/Zigbee_CarbonDioxide_Sensor/ci.json @@ -0,0 +1,6 @@ +{ + "fqbn_append": "PartitionScheme=zigbee,ZigbeeMode=ed", + "requires": [ + "CONFIG_SOC_IEEE802154_SUPPORTED=y" + ] +} diff --git a/libraries/Zigbee/examples/Zigbee_Occupancy_Sensor/README.md b/libraries/Zigbee/examples/Zigbee_Occupancy_Sensor/README.md new file mode 100644 index 00000000000..0c5dcd013f2 --- /dev/null +++ b/libraries/Zigbee/examples/Zigbee_Occupancy_Sensor/README.md @@ -0,0 +1,57 @@ +# Arduino-ESP32 Zigbee Occupancy Sensor Example + +This example shows how to configure the Zigbee end device and use it as a Home Automation (HA) occupancy sensor (PIR). + +# Supported Targets + +Currently, this example supports the following targets. + +| Supported Targets | ESP32-C6 | ESP32-H2 | +| ----------------- | -------- | -------- | + +## Hardware Required + +* A USB cable for power supply and programming + +### Configure the Project + +Set the Button GPIO by changing the `button` variable. By default, it's the pin `BOOT_PIN` (BOOT button on ESP32-C6 and ESP32-H2). +Set the Sensor GPIO by changing the `sensor_pin` variable. + +#### Using Arduino IDE + +To get more information about the Espressif boards see [Espressif Development Kits](https://www.espressif.com/en/products/devkits). + +* Before Compile/Verify, select the correct board: `Tools -> Board`. +* Select the End device Zigbee mode: `Tools -> Zigbee mode: Zigbee ED (end device)` +* Select Partition Scheme for Zigbee: `Tools -> Partition Scheme: Zigbee 4MB with spiffs` +* Select the COM port: `Tools -> Port: xxx` where the `xxx` is the detected COM port. +* Optional: Set debug level to verbose to see all logs from Zigbee stack: `Tools -> Core Debug Level: Verbose`. + +## Troubleshooting + +If the End device flashed with this example is not connecting to the coordinator, erase the flash of the End device before flashing the example to the board. + +***Important: Make sure you are using a good quality USB cable and that you have a reliable power source*** + +* **LED not blinking:** Check the wiring connection and the IO selection. +* **Programming Fail:** If the programming/flash procedure fails, try reducing the serial connection speed. +* **COM port not detected:** Check the USB cable and the USB to Serial driver installation. + +If the error persists, you can ask for help at the official [ESP32 forum](https://esp32.com) or see [Contribute](#contribute). + +## Contribute + +To know how to contribute to this project, see [How to contribute.](https://github.com/espressif/arduino-esp32/blob/master/CONTRIBUTING.rst) + +If you have any **feedback** or **issue** to report on this example/library, please open an issue or fix it by creating a new PR. Contributions are more than welcome! + +Before creating a new issue, be sure to try Troubleshooting and check if the same issue was already created by someone else. + +## Resources + +* Official ESP32 Forum: [Link](https://esp32.com) +* Arduino-ESP32 Official Repository: [espressif/arduino-esp32](https://github.com/espressif/arduino-esp32) +* ESP32-C6 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32-c6_datasheet_en.pdf) +* ESP32-H2 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32-h2_datasheet_en.pdf) +* Official ESP-IDF documentation: [ESP-IDF](https://idf.espressif.com) diff --git a/libraries/Zigbee/examples/Zigbee_Occupancy_Sensor/Zigbee_Occupancy_Sensor.ino b/libraries/Zigbee/examples/Zigbee_Occupancy_Sensor/Zigbee_Occupancy_Sensor.ino new file mode 100644 index 00000000000..46afdf3d273 --- /dev/null +++ b/libraries/Zigbee/examples/Zigbee_Occupancy_Sensor/Zigbee_Occupancy_Sensor.ino @@ -0,0 +1,103 @@ +// Copyright 2024 Espressif Systems (Shanghai) PTE LTD +// +// Licensed under the Apache License, Version 2.0 (the "License"); +// you may not use this file except in compliance with the License. +// You may obtain a copy of the License at +// +// http://www.apache.org/licenses/LICENSE-2.0 +// +// Unless required by applicable law or agreed to in writing, software +// distributed under the License is distributed on an "AS IS" BASIS, +// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +// See the License for the specific language governing permissions and +// limitations under the License. + +/** + * @brief This example demonstrates Zigbee occupancy sensor. + * + * The example demonstrates how to use Zigbee library to create a end device occupancy sensor. + * The occupancy sensor is a Zigbee end device, which is reporting data to the Zigbee network. + * Tested with PIR sensor HC-SR501 connected to GPIO4. + * + * Proper Zigbee mode must be selected in Tools->Zigbee mode + * and also the correct partition scheme must be selected in Tools->Partition Scheme. + * + * Please check the README.md for instructions and more detailed description. + * + * Created by Jan Procházka (https://github.com/P-R-O-C-H-Y/) + */ + +#ifndef ZIGBEE_MODE_ED +#error "Zigbee end device mode is not selected in Tools->Zigbee mode" +#endif + +#include "Zigbee.h" + +/* Zigbee occupancy sensor configuration */ +#define OCCUPANCY_SENSOR_ENDPOINT_NUMBER 10 +uint8_t button = BOOT_PIN; +uint8_t sensor_pin = 4; + +ZigbeeOccupancySensor zbOccupancySensor = ZigbeeOccupancySensor(OCCUPANCY_SENSOR_ENDPOINT_NUMBER); + +void setup() { + Serial.begin(115200); + + // Init button + PIR sensor + pinMode(button, INPUT_PULLUP); + pinMode(sensor_pin, INPUT); + + // Optional: set Zigbee device name and model + zbOccupancySensor.setManufacturerAndModel("Espressif", "ZigbeeOccupancyPIRSensor"); + + // Add endpoint to Zigbee Core + Zigbee.addEndpoint(&zbOccupancySensor); + + Serial.println("Starting Zigbee..."); + // When all EPs are registered, start Zigbee in End Device mode + if (!Zigbee.begin()) { + Serial.println("Zigbee failed to start!"); + Serial.println("Rebooting..."); + ESP.restart(); + } else { + Serial.println("Zigbee started successfully!"); + } + Serial.println("Connecting to network"); + while (!Zigbee.connected()) { + Serial.print("."); + delay(100); + } + Serial.println(); +} + +void loop() { + // Checking PIR sensor for occupancy change + static bool occupancy = false; + if (digitalRead(sensor_pin) == HIGH && !occupancy) { + // Update occupancy sensor value + zbOccupancySensor.setOccupancy(true); + zbOccupancySensor.report(); + occupancy = true; + } else if (digitalRead(sensor_pin) == LOW && occupancy) { + zbOccupancySensor.setOccupancy(false); + zbOccupancySensor.report(); + occupancy = false; + } + + // Checking button for factory reset + if (digitalRead(button) == LOW) { // Push button pressed + // Key debounce handling + delay(100); + int startTime = millis(); + while (digitalRead(button) == LOW) { + delay(50); + if ((millis() - startTime) > 3000) { + // If key pressed for more than 3secs, factory reset Zigbee and reboot + Serial.println("Resetting Zigbee to factory and rebooting in 1s."); + delay(1000); + Zigbee.factoryReset(); + } + } + } + delay(100); +} diff --git a/libraries/Zigbee/examples/Zigbee_Occupancy_Sensor/ci.json b/libraries/Zigbee/examples/Zigbee_Occupancy_Sensor/ci.json new file mode 100644 index 00000000000..7b7ccef8ed7 --- /dev/null +++ b/libraries/Zigbee/examples/Zigbee_Occupancy_Sensor/ci.json @@ -0,0 +1,6 @@ +{ + "fqbn_append": "PartitionScheme=zigbee,ZigbeeMode=ed", + "requires": [ + "CONFIG_SOC_IEEE802154_SUPPORTED=y" + ] +} diff --git a/libraries/Zigbee/examples/Zigbee_Pressure_Flow_Sensor/README.md b/libraries/Zigbee/examples/Zigbee_Pressure_Flow_Sensor/README.md new file mode 100644 index 00000000000..964c7503027 --- /dev/null +++ b/libraries/Zigbee/examples/Zigbee_Pressure_Flow_Sensor/README.md @@ -0,0 +1,72 @@ +# Arduino-ESP32 Zigbee Pressure + Flow Sensor Example + +This example shows how to configure the Zigbee end device and use it as a Home Automation (HA) simple sensor device type with pressure and flow measuring. + +# Supported Targets + +Currently, this example supports the following targets. + +| Supported Targets | ESP32-C6 | ESP32-H2 | +| ----------------- | -------- | -------- | + +## Pressure + Flow Sensor Functions + + * After this board first starts up, it would be configured locally to report the pressure and flow on change or every 30 seconds. + * By clicking the button (BOOT) on this board, this board will immediately send a report of the current measured flow and pressure to the network. + +## Hardware Required + +* A USB cable for power supply and programming + +### Configure the Project + +In this example, the internal temperature sensor is used to demonstrate reading of the flow and pressure sensors. +Set the Button GPIO by changing the `button` variable. By default, it's the pin `BOOT_PIN` (BOOT button on ESP32-C6 and ESP32-H2). + +#### Using Arduino IDE + +To get more information about the Espressif boards see [Espressif Development Kits](https://www.espressif.com/en/products/devkits). + +* Before Compile/Verify, select the correct board: `Tools -> Board`. +* Select the End device Zigbee mode: `Tools -> Zigbee mode: Zigbee ED (end device)` +* Select Partition Scheme for Zigbee: `Tools -> Partition Scheme: Zigbee 4MB with spiffs` +* Select the COM port: `Tools -> Port: xxx` where the `xxx` is the detected COM port. +* Optional: Set debug level to verbose to see all logs from Zigbee stack: `Tools -> Core Debug Level: Verbose`. + +## Troubleshooting + +If the End device flashed with this example is not connecting to the coordinator, erase the flash of the End device before flashing the example to the board. It is recommended to do this if you re-flash the coordinator. +You can do the following: + +* In the Arduino IDE go to the Tools menu and set `Erase All Flash Before Sketch Upload` to `Enabled`. +* Add to the sketch `Zigbee.factoryReset();` to reset the device and Zigbee stack. + +By default, the coordinator network is closed after rebooting or flashing new firmware. +To open the network you have 2 options: + +* Open network after reboot by setting `Zigbee.setRebootOpenNetwork(time);` before calling `Zigbee.begin();`. +* In application you can anytime call `Zigbee.openNetwork(time);` to open the network for devices to join. + +***Important: Make sure you are using a good quality USB cable and that you have a reliable power source*** + +* **LED not blinking:** Check the wiring connection and the IO selection. +* **Programming Fail:** If the programming/flash procedure fails, try reducing the serial connection speed. +* **COM port not detected:** Check the USB cable and the USB to Serial driver installation. + +If the error persists, you can ask for help at the official [ESP32 forum](https://esp32.com) or see [Contribute](#contribute). + +## Contribute + +To know how to contribute to this project, see [How to contribute.](https://github.com/espressif/arduino-esp32/blob/master/CONTRIBUTING.rst) + +If you have any **feedback** or **issue** to report on this example/library, please open an issue or fix it by creating a new PR. Contributions are more than welcome! + +Before creating a new issue, be sure to try Troubleshooting and check if the same issue was already created by someone else. + +## Resources + +* Official ESP32 Forum: [Link](https://esp32.com) +* Arduino-ESP32 Official Repository: [espressif/arduino-esp32](https://github.com/espressif/arduino-esp32) +* ESP32-C6 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32-c6_datasheet_en.pdf) +* ESP32-H2 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32-h2_datasheet_en.pdf) +* Official ESP-IDF documentation: [ESP-IDF](https://idf.espressif.com) diff --git a/libraries/Zigbee/examples/Zigbee_Pressure_Flow_Sensor/Zigbee_Pressure_Flow_Sensor.ino b/libraries/Zigbee/examples/Zigbee_Pressure_Flow_Sensor/Zigbee_Pressure_Flow_Sensor.ino new file mode 100644 index 00000000000..a652a22c493 --- /dev/null +++ b/libraries/Zigbee/examples/Zigbee_Pressure_Flow_Sensor/Zigbee_Pressure_Flow_Sensor.ino @@ -0,0 +1,128 @@ +// Copyright 2024 Espressif Systems (Shanghai) PTE LTD +// +// Licensed under the Apache License, Version 2.0 (the "License"); +// you may not use this file except in compliance with the License. +// You may obtain a copy of the License at +// +// http://www.apache.org/licenses/LICENSE-2.0 +// +// Unless required by applicable law or agreed to in writing, software +// distributed under the License is distributed on an "AS IS" BASIS, +// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +// See the License for the specific language governing permissions and +// limitations under the License. + +/** + * @brief This example demonstrates Zigbee temperature sensor. + * + * The example demonstrates how to use Zigbee library to create a end device temperature sensor. + * The temperature sensor is a Zigbee end device, which is controlled by a Zigbee coordinator. + * + * Proper Zigbee mode must be selected in Tools->Zigbee mode + * and also the correct partition scheme must be selected in Tools->Partition Scheme. + * + * Please check the README.md for instructions and more detailed description. + * + * Created by Jan Procházka (https://github.com/P-R-O-C-H-Y/) + */ + +#ifndef ZIGBEE_MODE_ED +#error "Zigbee end device mode is not selected in Tools->Zigbee mode" +#endif + +#include "Zigbee.h" + +/* Zigbee flow + pressure sensor configuration */ +#define FLOW_SENSOR_ENDPOINT_NUMBER 10 +#define PRESSURE_SENSOR_ENDPOINT_NUMBER 11 + +uint8_t button = BOOT_PIN; + +ZigbeeFlowSensor zbFlowSensor = ZigbeeFlowSensor(FLOW_SENSOR_ENDPOINT_NUMBER); +ZigbeePressureSensor zbPressureSensor = ZigbeePressureSensor(PRESSURE_SENSOR_ENDPOINT_NUMBER); + +void setup() { + Serial.begin(115200); + + // Init button switch + pinMode(button, INPUT_PULLUP); + + // Optional: set Zigbee device name and model + zbFlowSensor.setManufacturerAndModel("Espressif", "ZigbeeFlowSensor"); + + // Set minimum and maximum flow measurement value in 0,1 m3/h + zbFlowSensor.setMinMaxValue(0.0, 100.0); + + // Optional: Set tolerance for flow measurement in 0,1 m3/h + zbFlowSensor.setTolerance(1.0); + + // Optional: set Zigbee device name and model + zbPressureSensor.setManufacturerAndModel("Espressif", "ZigbeePressureSensor"); + + // Set minimum and maximum pressure measurement value in hPa + zbPressureSensor.setMinMaxValue(0, 10000); + + // Optional: Set tolerance for pressure measurement in hPa + zbPressureSensor.setTolerance(1); + + // Add endpoints to Zigbee Core + Zigbee.addEndpoint(&zbFlowSensor); + Zigbee.addEndpoint(&zbPressureSensor); + + Serial.println("Starting Zigbee..."); + // When all EPs are registered, start Zigbee in End Device mode + if (!Zigbee.begin()) { + Serial.println("Zigbee failed to start!"); + Serial.println("Rebooting..."); + ESP.restart(); + } else { + Serial.println("Zigbee started successfully!"); + } + Serial.println("Connecting to network"); + while (!Zigbee.connected()) { + Serial.print("."); + delay(100); + } + Serial.println(); + + // Set reporting interval for flow and pressure measurement in seconds, must be called after Zigbee.begin() + // min_interval and max_interval in seconds, delta (pressure change in hPa, flow change in 0,1 m3/h) + // if min = 1 and max = 0, reporting is sent only when temperature changes by delta + // if min = 0 and max = 10, reporting is sent every 10 seconds or temperature changes by delta + // if min = 0, max = 10 and delta = 0, reporting is sent every 10 seconds regardless of delta change + zbFlowSensor.setReporting(0, 30, 1.0); + zbPressureSensor.setReporting(0, 30, 1); +} + +void loop() { + static uint32_t timeCounter = 0; + + // Read flow and pressure sensors every 2s + if (!(timeCounter++ % 20)) { // delaying for 100ms x 20 = 2s + float flow_value = temperatureRead(); + uint16_t pressure_value = (uint16_t)temperatureRead() * 100; //*100 for demonstration so the value is in 1000-3000hPa + Serial.printf("Updating flow sensor value to %.2f m3/h\r\n", flow_value); + zbFlowSensor.setFlow(flow_value); + Serial.printf("Updating pressure sensor value to %d hPa\r\n", pressure_value); + zbPressureSensor.setPressure(pressure_value); + } + + // Checking button for factory reset and reporting + if (digitalRead(button) == LOW) { // Push button pressed + // Key debounce handling + delay(100); + int startTime = millis(); + while (digitalRead(button) == LOW) { + delay(50); + if ((millis() - startTime) > 3000) { + // If key pressed for more than 3secs, factory reset Zigbee and reboot + Serial.println("Resetting Zigbee to factory and rebooting in 1s."); + delay(1000); + Zigbee.factoryReset(); + } + } + zbFlowSensor.report(); + zbPressureSensor.report(); + } + delay(100); +} diff --git a/libraries/Zigbee/examples/Zigbee_Pressure_Flow_Sensor/ci.json b/libraries/Zigbee/examples/Zigbee_Pressure_Flow_Sensor/ci.json new file mode 100644 index 00000000000..7b7ccef8ed7 --- /dev/null +++ b/libraries/Zigbee/examples/Zigbee_Pressure_Flow_Sensor/ci.json @@ -0,0 +1,6 @@ +{ + "fqbn_append": "PartitionScheme=zigbee,ZigbeeMode=ed", + "requires": [ + "CONFIG_SOC_IEEE802154_SUPPORTED=y" + ] +} diff --git a/libraries/Zigbee/examples/Zigbee_Temp_Hum_Sensor_Sleepy/README.md b/libraries/Zigbee/examples/Zigbee_Temp_Hum_Sensor_Sleepy/README.md index d88b01cda3a..afaa12c0bfa 100644 --- a/libraries/Zigbee/examples/Zigbee_Temp_Hum_Sensor_Sleepy/README.md +++ b/libraries/Zigbee/examples/Zigbee_Temp_Hum_Sensor_Sleepy/README.md @@ -24,7 +24,7 @@ Currently, this example supports the following targets. ### Configure the Project In this example, to demonstrate the functionality the chip temperature is used and reported as temperature and humidity. -Set the Button GPIO by changing the `BUTTON_PIN` definition. By default, it's the pin `9` (BOOT button on ESP32-C6 and ESP32-H2). +Set the Button GPIO by changing the `button` variable. By default, it's the pin `BOOT_PIN` (BOOT button on ESP32-C6 and ESP32-H2). #### Using Arduino IDE diff --git a/libraries/Zigbee/examples/Zigbee_Temp_Hum_Sensor_Sleepy/Zigbee_Temp_Hum_Sensor_Sleepy.ino b/libraries/Zigbee/examples/Zigbee_Temp_Hum_Sensor_Sleepy/Zigbee_Temp_Hum_Sensor_Sleepy.ino index 2b342161199..60bd784cca9 100644 --- a/libraries/Zigbee/examples/Zigbee_Temp_Hum_Sensor_Sleepy/Zigbee_Temp_Hum_Sensor_Sleepy.ino +++ b/libraries/Zigbee/examples/Zigbee_Temp_Hum_Sensor_Sleepy/Zigbee_Temp_Hum_Sensor_Sleepy.ino @@ -55,11 +55,12 @@ void meausureAndSleep() { zbTempSensor.setHumidity(humidity); // Report temperature and humidity values - zbTempSensor.reportTemperature(); - zbTempSensor.reportHumidity(); - + zbTempSensor.report(); Serial.printf("Reported temperature: %.2f°C, Humidity: %.2f%%\r\n", temperature, humidity); + // Add small delay to allow the data to be sent before going to sleep + delay(100); + // Put device to deep sleep Serial.println("Going to sleep now"); esp_deep_sleep_start(); diff --git a/libraries/Zigbee/examples/Zigbee_Temperature_Sensor/README.md b/libraries/Zigbee/examples/Zigbee_Temperature_Sensor/README.md index f3dd9248f87..577bd7c8058 100644 --- a/libraries/Zigbee/examples/Zigbee_Temperature_Sensor/README.md +++ b/libraries/Zigbee/examples/Zigbee_Temperature_Sensor/README.md @@ -28,7 +28,7 @@ Functions: ### Configure the Project In this example, the internal temperature sensor task is reading the chip temperature. -Set the Button GPIO by changing the `BUTTON_PIN` definition. By default, it's the pin `9` (BOOT button on ESP32-C6 and ESP32-H2). +Set the Button GPIO by changing the `button` variable. By default, it's the pin `BOOT_PIN` (BOOT button on ESP32-C6 and ESP32-H2). #### Using Arduino IDE diff --git a/libraries/Zigbee/examples/Zigbee_Temperature_Sensor/Zigbee_Temperature_Sensor.ino b/libraries/Zigbee/examples/Zigbee_Temperature_Sensor/Zigbee_Temperature_Sensor.ino index 22b0c6fbeed..27aa2db97bd 100644 --- a/libraries/Zigbee/examples/Zigbee_Temperature_Sensor/Zigbee_Temperature_Sensor.ino +++ b/libraries/Zigbee/examples/Zigbee_Temperature_Sensor/Zigbee_Temperature_Sensor.ino @@ -63,7 +63,7 @@ void setup() { // Set minimum and maximum temperature measurement value (10-50°C is default range for chip temperature measurement) zbTempSensor.setMinMaxValue(10, 50); - // Set tolerance for temperature measurement in °C (lowest possible value is 0.01°C) + // Optional: Set tolerance for temperature measurement in °C (lowest possible value is 0.01°C) zbTempSensor.setTolerance(1); // Add endpoint to Zigbee Core @@ -89,7 +89,7 @@ void setup() { xTaskCreate(temp_sensor_value_update, "temp_sensor_update", 2048, NULL, 10, NULL); // Set reporting interval for temperature measurement in seconds, must be called after Zigbee.begin() - // min_interval and max_interval in seconds, delta (temp change in °C) + // min_interval and max_interval in seconds, delta (temp change in 0,1 °C) // if min = 1 and max = 0, reporting is sent only when temperature changes by delta // if min = 0 and max = 10, reporting is sent every 10 seconds or temperature changes by delta // if min = 0, max = 10 and delta = 0, reporting is sent every 10 seconds regardless of temperature change diff --git a/libraries/Zigbee/keywords.txt b/libraries/Zigbee/keywords.txt index 40e5dcec004..483d54eb712 100644 --- a/libraries/Zigbee/keywords.txt +++ b/libraries/Zigbee/keywords.txt @@ -18,6 +18,9 @@ ZigbeeColorDimmableLight KEYWORD1 ZigbeeColorDimmerSwitch KEYWORD1 ZigbeeTempSensor KEYWORD1 ZigbeeThermostat KEYWORD1 +ZigbeeFlowSensor KEYWORD1 +ZigbeePressureSensor KEYWORD1 +ZigbeeOccupancySensor KEYWORD1 # Other zigbee_role_t KEYWORD1 @@ -89,23 +92,39 @@ lightOnWithSceneRecall KEYWORD2 setLightLevel KEYWORD2 setLightColor KEYWORD2 -# ZigbeeTempSensor + humidity -setTemperature KEYWORD2 +# ZigbeeThermostat +onTempRecieve KEYWORD2 +onConfigRecieve KEYWORD2 +getTemperature KEYWORD2 +getSensorSettings KEYWORD2 +setTemperatureReporting KEYWORD2 + +# Common Zigbee Sensor setMinMaxValue KEYWORD2 setTolerance KEYWORD2 setReporting KEYWORD2 +report KEYWORD2 + +# ZigbeeTempSensor + humidity +setTemperature KEYWORD2 reportTemperature KEYWORD2 addHumiditySensor KEYWORD2 setHumidity KEYWORD2 setHumidityReporting KEYWORD2 reportHumidity KEYWORD2 -# ZigbeeThermostat -onTempRecieve KEYWORD2 -onConfigRecieve KEYWORD2 -getTemperature KEYWORD2 -getSensorSettings KEYWORD2 -setTemperatureReporting KEYWORD2 +# ZigbeeFlowSensor +setFlow KEYWORD2 + +# ZigbeePressureSensor +setPressure KEYWORD2 + +# ZigbeeOccupancySensor +setOccupancy KEYWORD2 +setSensorType KEYWORD2 + +# ZigbeeCarbonDioxideSensor +setCarbonDioxide KEYWORD2 ####################################### # Constants (LITERAL1) diff --git a/libraries/Zigbee/src/Zigbee.h b/libraries/Zigbee/src/Zigbee.h index 98674a9d115..727761c900d 100644 --- a/libraries/Zigbee/src/Zigbee.h +++ b/libraries/Zigbee/src/Zigbee.h @@ -13,3 +13,7 @@ #include "ep/ZigbeeColorDimmerSwitch.h" #include "ep/ZigbeeTempSensor.h" #include "ep/ZigbeeThermostat.h" +#include "ep/ZigbeePressureSensor.h" +#include "ep/ZigbeeFlowSensor.h" +#include "ep/ZigbeeOccupancySensor.h" +#include "ep/ZigbeeCarbonDioxideSensor.h" diff --git a/libraries/Zigbee/src/ep/ZigbeeCarbonDioxideSensor.cpp b/libraries/Zigbee/src/ep/ZigbeeCarbonDioxideSensor.cpp new file mode 100644 index 00000000000..89454c057e3 --- /dev/null +++ b/libraries/Zigbee/src/ep/ZigbeeCarbonDioxideSensor.cpp @@ -0,0 +1,109 @@ +#include "ZigbeeCarbonDioxideSensor.h" +#if SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED + +esp_zb_cluster_list_t *zigbee_carbon_dioxide_sensor_clusters_create(zigbee_carbon_dioxide_sensor_cfg_t *carbon_dioxide_sensor) { + esp_zb_basic_cluster_cfg_t *basic_cfg = carbon_dioxide_sensor ? &(carbon_dioxide_sensor->basic_cfg) : NULL; + esp_zb_identify_cluster_cfg_t *identify_cfg = carbon_dioxide_sensor ? &(carbon_dioxide_sensor->identify_cfg) : NULL; + esp_zb_carbon_dioxide_measurement_cluster_cfg_t *carbon_dioxide_meas_cfg = carbon_dioxide_sensor ? &(carbon_dioxide_sensor->carbon_dioxide_meas_cfg) : NULL; + esp_zb_cluster_list_t *cluster_list = esp_zb_zcl_cluster_list_create(); + esp_zb_cluster_list_add_basic_cluster(cluster_list, esp_zb_basic_cluster_create(basic_cfg), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_cluster_list_add_identify_cluster(cluster_list, esp_zb_identify_cluster_create(identify_cfg), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_cluster_list_add_carbon_dioxide_measurement_cluster( + cluster_list, esp_zb_carbon_dioxide_measurement_cluster_create(carbon_dioxide_meas_cfg), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE + ); + esp_zb_cluster_list_add_identify_cluster(cluster_list, esp_zb_zcl_attr_list_create(ESP_ZB_ZCL_CLUSTER_ID_IDENTIFY), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + return cluster_list; +} + +ZigbeeCarbonDioxideSensor::ZigbeeCarbonDioxideSensor(uint8_t endpoint) : ZigbeeEP(endpoint) { + _device_id = ESP_ZB_HA_SIMPLE_SENSOR_DEVICE_ID; + + //Create custom pressure sensor configuration + zigbee_carbon_dioxide_sensor_cfg_t carbon_dioxide_sensor_cfg = ZIGBEE_DEFAULT_CARBON_DIOXIDE_SENSOR_CONFIG(); + _cluster_list = zigbee_carbon_dioxide_sensor_clusters_create(&carbon_dioxide_sensor_cfg); + + _ep_config = {.endpoint = _endpoint, .app_profile_id = ESP_ZB_AF_HA_PROFILE_ID, .app_device_id = ESP_ZB_HA_SIMPLE_SENSOR_DEVICE_ID, .app_device_version = 0}; +} + +void ZigbeeCarbonDioxideSensor::setMinMaxValue(float min, float max) { + float zb_min = min / 1000000.0f; + float zb_max = max / 1000000.0f; + esp_zb_attribute_list_t *carbon_dioxide_measure_cluster = + esp_zb_cluster_list_get_cluster(_cluster_list, ESP_ZB_ZCL_CLUSTER_ID_CARBON_DIOXIDE_MEASUREMENT, ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_cluster_update_attr(carbon_dioxide_measure_cluster, ESP_ZB_ZCL_ATTR_CARBON_DIOXIDE_MEASUREMENT_MIN_MEASURED_VALUE_ID, (void *)&zb_min); + esp_zb_cluster_update_attr(carbon_dioxide_measure_cluster, ESP_ZB_ZCL_ATTR_CARBON_DIOXIDE_MEASUREMENT_MAX_MEASURED_VALUE_ID, (void *)&zb_max); +} + +void ZigbeeCarbonDioxideSensor::setTolerance(float tolerance) { + float zb_tolerance = tolerance / 1000000.0f; + esp_zb_attribute_list_t *carbon_dioxide_measure_cluster = + esp_zb_cluster_list_get_cluster(_cluster_list, ESP_ZB_ZCL_CLUSTER_ID_CARBON_DIOXIDE_MEASUREMENT, ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_temperature_meas_cluster_add_attr(carbon_dioxide_measure_cluster, ESP_ZB_ZCL_ATTR_CARBON_DIOXIDE_MEASUREMENT_TOLERANCE_ID, (void *)&zb_tolerance); +} + +void ZigbeeCarbonDioxideSensor::setReporting(uint16_t min_interval, uint16_t max_interval, uint16_t delta) { + if (delta > 0) { + log_e("Delta reporting is currently not supported by the carbon dioxide sensor"); + } + // clang-format off + esp_zb_zcl_reporting_info_t reporting_info = { + .direction = ESP_ZB_ZCL_CMD_DIRECTION_TO_SRV, + .ep = _endpoint, + .cluster_id = ESP_ZB_ZCL_CLUSTER_ID_CARBON_DIOXIDE_MEASUREMENT, + .cluster_role = ESP_ZB_ZCL_CLUSTER_SERVER_ROLE, + .attr_id = ESP_ZB_ZCL_ATTR_CARBON_DIOXIDE_MEASUREMENT_MEASURED_VALUE_ID, + .u = + { + .send_info = + { + .min_interval = min_interval, + .max_interval = max_interval, + .delta = + { + .u16 = delta, + }, + .def_min_interval = min_interval, + .def_max_interval = max_interval, + }, + }, + .dst = + { + .profile_id = ESP_ZB_AF_HA_PROFILE_ID, + }, + .manuf_code = ESP_ZB_ZCL_ATTR_NON_MANUFACTURER_SPECIFIC, + }; + // clang-format on + esp_zb_lock_acquire(portMAX_DELAY); + esp_zb_zcl_update_reporting_info(&reporting_info); + esp_zb_lock_release(); +} + +void ZigbeeCarbonDioxideSensor::setCarbonDioxide(float carbon_dioxide) { + float zb_carbon_dioxide = carbon_dioxide / 1000000.0f; + log_v("Updating carbon dioxide sensor value..."); + /* Update carbon dioxide sensor measured value */ + log_d("Setting carbon dioxide to %0.1f", carbon_dioxide); + esp_zb_lock_acquire(portMAX_DELAY); + esp_zb_zcl_set_attribute_val( + _endpoint, ESP_ZB_ZCL_CLUSTER_ID_CARBON_DIOXIDE_MEASUREMENT, ESP_ZB_ZCL_CLUSTER_SERVER_ROLE, ESP_ZB_ZCL_ATTR_CARBON_DIOXIDE_MEASUREMENT_MEASURED_VALUE_ID, + &zb_carbon_dioxide, false + ); + esp_zb_lock_release(); +} + +void ZigbeeCarbonDioxideSensor::report() { + /* Send report attributes command */ + esp_zb_zcl_report_attr_cmd_t report_attr_cmd; + report_attr_cmd.address_mode = ESP_ZB_APS_ADDR_MODE_DST_ADDR_ENDP_NOT_PRESENT; + report_attr_cmd.attributeID = ESP_ZB_ZCL_ATTR_CARBON_DIOXIDE_MEASUREMENT_MEASURED_VALUE_ID; + report_attr_cmd.direction = ESP_ZB_ZCL_CMD_DIRECTION_TO_CLI; + report_attr_cmd.clusterID = ESP_ZB_ZCL_CLUSTER_ID_CARBON_DIOXIDE_MEASUREMENT; + report_attr_cmd.zcl_basic_cmd.src_endpoint = _endpoint; + + esp_zb_lock_acquire(portMAX_DELAY); + esp_zb_zcl_report_attr_cmd_req(&report_attr_cmd); + esp_zb_lock_release(); + log_v("Carbon dioxide report sent"); +} + +#endif //SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED diff --git a/libraries/Zigbee/src/ep/ZigbeeCarbonDioxideSensor.h b/libraries/Zigbee/src/ep/ZigbeeCarbonDioxideSensor.h new file mode 100644 index 00000000000..71c353d4695 --- /dev/null +++ b/libraries/Zigbee/src/ep/ZigbeeCarbonDioxideSensor.h @@ -0,0 +1,61 @@ +/* Class of Zigbee Pressure sensor endpoint inherited from common EP class */ + +#pragma once + +#include "soc/soc_caps.h" +#include "sdkconfig.h" +#if SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED + +#include "ZigbeeEP.h" +#include "ha/esp_zigbee_ha_standard.h" + +// clang-format off +#define ZIGBEE_DEFAULT_CARBON_DIOXIDE_SENSOR_CONFIG() \ + { \ + .basic_cfg = \ + { \ + .zcl_version = ESP_ZB_ZCL_BASIC_ZCL_VERSION_DEFAULT_VALUE, \ + .power_source = ESP_ZB_ZCL_BASIC_POWER_SOURCE_DEFAULT_VALUE, \ + }, \ + .identify_cfg = \ + { \ + .identify_time = ESP_ZB_ZCL_IDENTIFY_IDENTIFY_TIME_DEFAULT_VALUE, \ + }, \ + .carbon_dioxide_meas_cfg = \ + { \ + .measured_value = 0.0, \ + .min_measured_value = 0.0, \ + .max_measured_value = 1.0, \ + }, \ + } +// clang-format on + +typedef struct zigbee_carbon_dioxide_sensor_cfg_s { + esp_zb_basic_cluster_cfg_t basic_cfg; + esp_zb_identify_cluster_cfg_t identify_cfg; + esp_zb_carbon_dioxide_measurement_cluster_cfg_t carbon_dioxide_meas_cfg; +} zigbee_carbon_dioxide_sensor_cfg_t; + +class ZigbeeCarbonDioxideSensor : public ZigbeeEP { +public: + ZigbeeCarbonDioxideSensor(uint8_t endpoint); + ~ZigbeeCarbonDioxideSensor(); + + // Set the carbon dioxide value in ppm + void setCarbonDioxide(float carbon_dioxide); + + // Set the min and max value for the carbon dioxide sensor in ppm + void setMinMaxValue(float min, float max); + + // Set the tolerance value for the carbon dioxide sensor in ppm + void setTolerance(float tolerance); + + // Set the reporting interval for carbon dioxide measurement in seconds and delta (carbon dioxide change in ppm) + // NOTE: Delta reporting is currently not supported by the carbon dioxide sensor + void setReporting(uint16_t min_interval, uint16_t max_interval, uint16_t delta); + + // Report the carbon dioxide value + void report(); +}; + +#endif //SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED diff --git a/libraries/Zigbee/src/ep/ZigbeeFlowSensor.cpp b/libraries/Zigbee/src/ep/ZigbeeFlowSensor.cpp new file mode 100644 index 00000000000..6adf8172194 --- /dev/null +++ b/libraries/Zigbee/src/ep/ZigbeeFlowSensor.cpp @@ -0,0 +1,104 @@ +#include "ZigbeeFlowSensor.h" +#if SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED + +esp_zb_cluster_list_t *zigbee_flow_sensor_clusters_create(zigbee_flow_sensor_cfg_t *flow_sensor) { + esp_zb_basic_cluster_cfg_t *basic_cfg = flow_sensor ? &(flow_sensor->basic_cfg) : NULL; + esp_zb_identify_cluster_cfg_t *identify_cfg = flow_sensor ? &(flow_sensor->identify_cfg) : NULL; + esp_zb_flow_meas_cluster_cfg_t *flow_meas_cfg = flow_sensor ? &(flow_sensor->flow_meas_cfg) : NULL; + esp_zb_cluster_list_t *cluster_list = esp_zb_zcl_cluster_list_create(); + esp_zb_cluster_list_add_basic_cluster(cluster_list, esp_zb_basic_cluster_create(basic_cfg), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_cluster_list_add_identify_cluster(cluster_list, esp_zb_identify_cluster_create(identify_cfg), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_cluster_list_add_flow_meas_cluster(cluster_list, esp_zb_flow_meas_cluster_create(flow_meas_cfg), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_cluster_list_add_identify_cluster(cluster_list, esp_zb_zcl_attr_list_create(ESP_ZB_ZCL_CLUSTER_ID_IDENTIFY), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + return cluster_list; +} + +ZigbeeFlowSensor::ZigbeeFlowSensor(uint8_t endpoint) : ZigbeeEP(endpoint) { + _device_id = ESP_ZB_HA_SIMPLE_SENSOR_DEVICE_ID; + + //Create custom pressure sensor configuration + zigbee_flow_sensor_cfg_t flow_sensor_cfg = ZIGBEE_DEFAULT_FLOW_SENSOR_CONFIG(); + _cluster_list = zigbee_flow_sensor_clusters_create(&flow_sensor_cfg); + + _ep_config = {.endpoint = _endpoint, .app_profile_id = ESP_ZB_AF_HA_PROFILE_ID, .app_device_id = ESP_ZB_HA_SIMPLE_SENSOR_DEVICE_ID, .app_device_version = 0}; +} + +void ZigbeeFlowSensor::setMinMaxValue(float min, float max) { + uint16_t zb_min = (uint16_t)(min * 10); + uint16_t zb_max = (uint16_t)(max * 10); + esp_zb_attribute_list_t *flow_measure_cluster = + esp_zb_cluster_list_get_cluster(_cluster_list, ESP_ZB_ZCL_CLUSTER_ID_FLOW_MEASUREMENT, ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_cluster_update_attr(flow_measure_cluster, ESP_ZB_ZCL_ATTR_FLOW_MEASUREMENT_MIN_VALUE_ID, (void *)&zb_min); + esp_zb_cluster_update_attr(flow_measure_cluster, ESP_ZB_ZCL_ATTR_FLOW_MEASUREMENT_MAX_VALUE_ID, (void *)&zb_max); +} + +void ZigbeeFlowSensor::setTolerance(float tolerance) { + // Convert tolerance to ZCL uint16_t + uint16_t zb_tolerance = (uint16_t)(tolerance * 10); + esp_zb_attribute_list_t *flow_measure_cluster = + esp_zb_cluster_list_get_cluster(_cluster_list, ESP_ZB_ZCL_CLUSTER_ID_FLOW_MEASUREMENT, ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_flow_meas_cluster_add_attr(flow_measure_cluster, ESP_ZB_ZCL_ATTR_FLOW_MEASUREMENT_TOLERANCE_ID, (void *)&zb_tolerance); +} + +void ZigbeeFlowSensor::setReporting(uint16_t min_interval, uint16_t max_interval, float delta) { + // clang-format off + esp_zb_zcl_reporting_info_t reporting_info = { + .direction = ESP_ZB_ZCL_CMD_DIRECTION_TO_SRV, + .ep = _endpoint, + .cluster_id = ESP_ZB_ZCL_CLUSTER_ID_FLOW_MEASUREMENT, + .cluster_role = ESP_ZB_ZCL_CLUSTER_SERVER_ROLE, + .attr_id = ESP_ZB_ZCL_ATTR_FLOW_MEASUREMENT_VALUE_ID, + .u = + { + .send_info = + { + .min_interval = min_interval, + .max_interval = max_interval, + .delta = + { + .u16 = (uint16_t)(delta * 10), // Convert delta to ZCL uint16_t + }, + .def_min_interval = min_interval, + .def_max_interval = max_interval, + }, + }, + .dst = + { + .profile_id = ESP_ZB_AF_HA_PROFILE_ID, + }, + .manuf_code = ESP_ZB_ZCL_ATTR_NON_MANUFACTURER_SPECIFIC, + }; + // clang-format on + esp_zb_lock_acquire(portMAX_DELAY); + esp_zb_zcl_update_reporting_info(&reporting_info); + esp_zb_lock_release(); +} + +void ZigbeeFlowSensor::setFlow(float flow) { + uint16_t zb_flow = (uint16_t)(flow * 10); + log_v("Updating flow sensor value..."); + /* Update temperature sensor measured value */ + log_d("Setting flow to %d", zb_flow); + esp_zb_lock_acquire(portMAX_DELAY); + esp_zb_zcl_set_attribute_val( + _endpoint, ESP_ZB_ZCL_CLUSTER_ID_FLOW_MEASUREMENT, ESP_ZB_ZCL_CLUSTER_SERVER_ROLE, ESP_ZB_ZCL_ATTR_FLOW_MEASUREMENT_VALUE_ID, &zb_flow, false + ); + esp_zb_lock_release(); +} + +void ZigbeeFlowSensor::report() { + /* Send report attributes command */ + esp_zb_zcl_report_attr_cmd_t report_attr_cmd; + report_attr_cmd.address_mode = ESP_ZB_APS_ADDR_MODE_DST_ADDR_ENDP_NOT_PRESENT; + report_attr_cmd.attributeID = ESP_ZB_ZCL_ATTR_FLOW_MEASUREMENT_VALUE_ID; + report_attr_cmd.direction = ESP_ZB_ZCL_CMD_DIRECTION_TO_CLI; + report_attr_cmd.clusterID = ESP_ZB_ZCL_CLUSTER_ID_FLOW_MEASUREMENT; + report_attr_cmd.zcl_basic_cmd.src_endpoint = _endpoint; + + esp_zb_lock_acquire(portMAX_DELAY); + esp_zb_zcl_report_attr_cmd_req(&report_attr_cmd); + esp_zb_lock_release(); + log_v("Flow report sent"); +} + +#endif //SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED diff --git a/libraries/Zigbee/src/ep/ZigbeeFlowSensor.h b/libraries/Zigbee/src/ep/ZigbeeFlowSensor.h new file mode 100644 index 00000000000..3514e2fcc1b --- /dev/null +++ b/libraries/Zigbee/src/ep/ZigbeeFlowSensor.h @@ -0,0 +1,60 @@ +/* Class of Zigbee Flow sensor endpoint inherited from common EP class */ + +#pragma once + +#include "soc/soc_caps.h" +#include "sdkconfig.h" +#if SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED + +#include "ZigbeeEP.h" +#include "ha/esp_zigbee_ha_standard.h" + +// clang-format off +#define ZIGBEE_DEFAULT_FLOW_SENSOR_CONFIG() \ + { \ + .basic_cfg = \ + { \ + .zcl_version = ESP_ZB_ZCL_BASIC_ZCL_VERSION_DEFAULT_VALUE, \ + .power_source = ESP_ZB_ZCL_BASIC_POWER_SOURCE_DEFAULT_VALUE, \ + }, \ + .identify_cfg = \ + { \ + .identify_time = ESP_ZB_ZCL_IDENTIFY_IDENTIFY_TIME_DEFAULT_VALUE, \ + }, \ + .flow_meas_cfg = \ + { \ + .measured_value = 0, \ + .min_value = 0, \ + .max_value = 0x7FFF, \ + }, \ + } +// clang-format on + +typedef struct zigbee_flow_sensor_cfg_s { + esp_zb_basic_cluster_cfg_t basic_cfg; + esp_zb_identify_cluster_cfg_t identify_cfg; + esp_zb_flow_meas_cluster_cfg_t flow_meas_cfg; +} zigbee_flow_sensor_cfg_t; + +class ZigbeeFlowSensor : public ZigbeeEP { +public: + ZigbeeFlowSensor(uint8_t endpoint); + ~ZigbeeFlowSensor(); + + // Set the flow value in 0,1 m3/h + void setFlow(float value); + + // Set the min and max value for the flow sensor in 0,1 m3/h + void setMinMaxValue(float min, float max); + + // Set the tolerance value for the flow sensor in 0,01 m3/h + void setTolerance(float tolerance); + + // Set the reporting interval for flow measurement in seconds and delta (temp change in 0,1 m3/h) + void setReporting(uint16_t min_interval, uint16_t max_interval, float delta); + + // Report the flow value + void report(); +}; + +#endif //SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED diff --git a/libraries/Zigbee/src/ep/ZigbeeOccupancySensor.cpp b/libraries/Zigbee/src/ep/ZigbeeOccupancySensor.cpp new file mode 100644 index 00000000000..3a7acee040c --- /dev/null +++ b/libraries/Zigbee/src/ep/ZigbeeOccupancySensor.cpp @@ -0,0 +1,60 @@ +#include "ZigbeeOccupancySensor.h" +#if SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED + +esp_zb_cluster_list_t *zigbee_occupancy_sensor_clusters_create(zigbee_occupancy_sensor_cfg_t *occupancy_sensor) { + esp_zb_basic_cluster_cfg_t *basic_cfg = occupancy_sensor ? &(occupancy_sensor->basic_cfg) : NULL; + esp_zb_identify_cluster_cfg_t *identify_cfg = occupancy_sensor ? &(occupancy_sensor->identify_cfg) : NULL; + esp_zb_occupancy_sensing_cluster_cfg_t *occupancy_meas_cfg = occupancy_sensor ? &(occupancy_sensor->occupancy_meas_cfg) : NULL; + esp_zb_cluster_list_t *cluster_list = esp_zb_zcl_cluster_list_create(); + esp_zb_cluster_list_add_basic_cluster(cluster_list, esp_zb_basic_cluster_create(basic_cfg), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_cluster_list_add_identify_cluster(cluster_list, esp_zb_identify_cluster_create(identify_cfg), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_cluster_list_add_occupancy_sensing_cluster(cluster_list, esp_zb_occupancy_sensing_cluster_create(occupancy_meas_cfg), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_cluster_list_add_identify_cluster(cluster_list, esp_zb_zcl_attr_list_create(ESP_ZB_ZCL_CLUSTER_ID_IDENTIFY), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + return cluster_list; +} + +ZigbeeOccupancySensor::ZigbeeOccupancySensor(uint8_t endpoint) : ZigbeeEP(endpoint) { + _device_id = ESP_ZB_HA_SIMPLE_SENSOR_DEVICE_ID; + + //Create custom occupancy sensor configuration + zigbee_occupancy_sensor_cfg_t occupancy_sensor_cfg = ZIGBEE_DEFAULT_OCCUPANCY_SENSOR_CONFIG(); + _cluster_list = zigbee_occupancy_sensor_clusters_create(&occupancy_sensor_cfg); + + _ep_config = {.endpoint = _endpoint, .app_profile_id = ESP_ZB_AF_HA_PROFILE_ID, .app_device_id = ESP_ZB_HA_SIMPLE_SENSOR_DEVICE_ID, .app_device_version = 0}; +} + +void ZigbeeOccupancySensor::setSensorType(uint8_t sensor_type) { + uint8_t sensor_type_bitmap = 1 << sensor_type; + esp_zb_attribute_list_t *occupancy_sens_cluster = + esp_zb_cluster_list_get_cluster(_cluster_list, ESP_ZB_ZCL_CLUSTER_ID_OCCUPANCY_SENSING, ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_cluster_update_attr(occupancy_sens_cluster, ESP_ZB_ZCL_ATTR_OCCUPANCY_SENSING_OCCUPANCY_SENSOR_TYPE_ID, (void *)&sensor_type); + esp_zb_cluster_update_attr(occupancy_sens_cluster, ESP_ZB_ZCL_ATTR_OCCUPANCY_SENSING_OCCUPANCY_SENSOR_TYPE_BITMAP_ID, (void *)&sensor_type_bitmap); +} + +void ZigbeeOccupancySensor::setOccupancy(bool occupied) { + log_v("Updating occupancy sensor value..."); + /* Update occupancy sensor value */ + log_d("Setting occupancy to %d", occupied); + esp_zb_lock_acquire(portMAX_DELAY); + esp_zb_zcl_set_attribute_val( + _endpoint, ESP_ZB_ZCL_CLUSTER_ID_OCCUPANCY_SENSING, ESP_ZB_ZCL_CLUSTER_SERVER_ROLE, ESP_ZB_ZCL_ATTR_OCCUPANCY_SENSING_OCCUPANCY_ID, &occupied, false + ); + esp_zb_lock_release(); +} + +void ZigbeeOccupancySensor::report() { + /* Send report attributes command */ + esp_zb_zcl_report_attr_cmd_t report_attr_cmd; + report_attr_cmd.address_mode = ESP_ZB_APS_ADDR_MODE_DST_ADDR_ENDP_NOT_PRESENT; + report_attr_cmd.attributeID = ESP_ZB_ZCL_ATTR_OCCUPANCY_SENSING_OCCUPANCY_ID; + report_attr_cmd.direction = ESP_ZB_ZCL_CMD_DIRECTION_TO_CLI; + report_attr_cmd.clusterID = ESP_ZB_ZCL_CLUSTER_ID_OCCUPANCY_SENSING; + report_attr_cmd.zcl_basic_cmd.src_endpoint = _endpoint; + + esp_zb_lock_acquire(portMAX_DELAY); + esp_zb_zcl_report_attr_cmd_req(&report_attr_cmd); + esp_zb_lock_release(); + log_v("Occupancy report sent"); +} + +#endif //SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED diff --git a/libraries/Zigbee/src/ep/ZigbeeOccupancySensor.h b/libraries/Zigbee/src/ep/ZigbeeOccupancySensor.h new file mode 100644 index 00000000000..e4b25c063e5 --- /dev/null +++ b/libraries/Zigbee/src/ep/ZigbeeOccupancySensor.h @@ -0,0 +1,54 @@ +/* Class of Zigbee Pressure sensor endpoint inherited from common EP class */ + +#pragma once + +#include "soc/soc_caps.h" +#include "sdkconfig.h" +#if SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED + +#include "ZigbeeEP.h" +#include "ha/esp_zigbee_ha_standard.h" + +// clang-format off +#define ZIGBEE_DEFAULT_OCCUPANCY_SENSOR_CONFIG() \ + { \ + .basic_cfg = \ + { \ + .zcl_version = ESP_ZB_ZCL_BASIC_ZCL_VERSION_DEFAULT_VALUE, \ + .power_source = ESP_ZB_ZCL_BASIC_POWER_SOURCE_DEFAULT_VALUE, \ + }, \ + .identify_cfg = \ + { \ + .identify_time = ESP_ZB_ZCL_IDENTIFY_IDENTIFY_TIME_DEFAULT_VALUE, \ + }, \ + .occupancy_meas_cfg = \ + { \ + .occupancy = ESP_ZB_ZCL_OCCUPANCY_SENSING_OCCUPANCY_UNOCCUPIED, \ + .sensor_type = ESP_ZB_ZCL_OCCUPANCY_SENSING_OCCUPANCY_SENSOR_TYPE_PIR, \ + .sensor_type_bitmap = (1 << ESP_ZB_ZCL_OCCUPANCY_SENSING_OCCUPANCY_SENSOR_TYPE_PIR), \ + }, \ + } +// clang-format on + +typedef struct zigbee_occupancy_sensor_cfg_s { + esp_zb_basic_cluster_cfg_t basic_cfg; + esp_zb_identify_cluster_cfg_t identify_cfg; + esp_zb_occupancy_sensing_cluster_cfg_t occupancy_meas_cfg; +} zigbee_occupancy_sensor_cfg_t; + +class ZigbeeOccupancySensor : public ZigbeeEP { +public: + ZigbeeOccupancySensor(uint8_t endpoint); + ~ZigbeeOccupancySensor(); + + // Set the occupancy value. True for occupied, false for unoccupied + void setOccupancy(bool occupied); + + // Set the sensor type, see esp_zb_zcl_occupancy_sensing_occupancy_sensor_type_t + void setSensorType(uint8_t sensor_type); + + // Report the occupancy value + void report(); +}; + +#endif //SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED diff --git a/libraries/Zigbee/src/ep/ZigbeePressureSensor.cpp b/libraries/Zigbee/src/ep/ZigbeePressureSensor.cpp new file mode 100644 index 00000000000..9415502215d --- /dev/null +++ b/libraries/Zigbee/src/ep/ZigbeePressureSensor.cpp @@ -0,0 +1,100 @@ +#include "ZigbeePressureSensor.h" +#if SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED + +esp_zb_cluster_list_t *zigbee_pressure_sensor_clusters_create(zigbee_pressure_sensor_cfg_t *pressure_sensor) { + esp_zb_basic_cluster_cfg_t *basic_cfg = pressure_sensor ? &(pressure_sensor->basic_cfg) : NULL; + esp_zb_identify_cluster_cfg_t *identify_cfg = pressure_sensor ? &(pressure_sensor->identify_cfg) : NULL; + esp_zb_pressure_meas_cluster_cfg_t *pressure_meas_cfg = pressure_sensor ? &(pressure_sensor->pressure_meas_cfg) : NULL; + esp_zb_cluster_list_t *cluster_list = esp_zb_zcl_cluster_list_create(); + esp_zb_cluster_list_add_basic_cluster(cluster_list, esp_zb_basic_cluster_create(basic_cfg), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_cluster_list_add_identify_cluster(cluster_list, esp_zb_identify_cluster_create(identify_cfg), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_cluster_list_add_pressure_meas_cluster(cluster_list, esp_zb_pressure_meas_cluster_create(pressure_meas_cfg), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_cluster_list_add_identify_cluster(cluster_list, esp_zb_zcl_attr_list_create(ESP_ZB_ZCL_CLUSTER_ID_IDENTIFY), ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + return cluster_list; +} + +ZigbeePressureSensor::ZigbeePressureSensor(uint8_t endpoint) : ZigbeeEP(endpoint) { + _device_id = ESP_ZB_HA_SIMPLE_SENSOR_DEVICE_ID; + + //Create custom pressure sensor configuration + zigbee_pressure_sensor_cfg_t presssure_sensor_cfg = ZIGBEE_DEFAULT_PRESSURE_SENSOR_CONFIG(); + _cluster_list = zigbee_pressure_sensor_clusters_create(&presssure_sensor_cfg); + + _ep_config = {.endpoint = _endpoint, .app_profile_id = ESP_ZB_AF_HA_PROFILE_ID, .app_device_id = ESP_ZB_HA_SIMPLE_SENSOR_DEVICE_ID, .app_device_version = 0}; +} + +void ZigbeePressureSensor::setMinMaxValue(int16_t min, int16_t max) { + + esp_zb_attribute_list_t *pressure_measure_cluster = + esp_zb_cluster_list_get_cluster(_cluster_list, ESP_ZB_ZCL_CLUSTER_ID_PRESSURE_MEASUREMENT, ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_cluster_update_attr(pressure_measure_cluster, ESP_ZB_ZCL_ATTR_PRESSURE_MEASUREMENT_MIN_VALUE_ID, (void *)&min); + esp_zb_cluster_update_attr(pressure_measure_cluster, ESP_ZB_ZCL_ATTR_PRESSURE_MEASUREMENT_MAX_VALUE_ID, (void *)&max); +} + +void ZigbeePressureSensor::setTolerance(uint16_t tolerance) { + esp_zb_attribute_list_t *pressure_measure_cluster = + esp_zb_cluster_list_get_cluster(_cluster_list, ESP_ZB_ZCL_CLUSTER_ID_PRESSURE_MEASUREMENT, ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + esp_zb_temperature_meas_cluster_add_attr(pressure_measure_cluster, ESP_ZB_ZCL_ATTR_PRESSURE_MEASUREMENT_TOLERANCE_ID, (void *)&tolerance); +} + +void ZigbeePressureSensor::setReporting(uint16_t min_interval, uint16_t max_interval, uint16_t delta) { + // clang-format off + esp_zb_zcl_reporting_info_t reporting_info = { + .direction = ESP_ZB_ZCL_CMD_DIRECTION_TO_SRV, + .ep = _endpoint, + .cluster_id = ESP_ZB_ZCL_CLUSTER_ID_PRESSURE_MEASUREMENT, + .cluster_role = ESP_ZB_ZCL_CLUSTER_SERVER_ROLE, + .attr_id = ESP_ZB_ZCL_ATTR_PRESSURE_MEASUREMENT_VALUE_ID, + .u = + { + .send_info = + { + .min_interval = min_interval, + .max_interval = max_interval, + .delta = + { + .u16 = delta, // x hPa + }, + .def_min_interval = min_interval, + .def_max_interval = max_interval, + }, + }, + .dst = + { + .profile_id = ESP_ZB_AF_HA_PROFILE_ID, + }, + .manuf_code = ESP_ZB_ZCL_ATTR_NON_MANUFACTURER_SPECIFIC, + }; + // clang-format on + esp_zb_lock_acquire(portMAX_DELAY); + esp_zb_zcl_update_reporting_info(&reporting_info); + esp_zb_lock_release(); +} + +void ZigbeePressureSensor::setPressure(int16_t pressure) { + log_v("Updating pressure sensor value..."); + /* Update temperature sensor measured value */ + log_d("Setting pressure to %d hPa", pressure); + esp_zb_lock_acquire(portMAX_DELAY); + esp_zb_zcl_set_attribute_val( + _endpoint, ESP_ZB_ZCL_CLUSTER_ID_PRESSURE_MEASUREMENT, ESP_ZB_ZCL_CLUSTER_SERVER_ROLE, ESP_ZB_ZCL_ATTR_PRESSURE_MEASUREMENT_VALUE_ID, &pressure, false + ); + esp_zb_lock_release(); +} + +void ZigbeePressureSensor::report() { + /* Send report attributes command */ + esp_zb_zcl_report_attr_cmd_t report_attr_cmd; + report_attr_cmd.address_mode = ESP_ZB_APS_ADDR_MODE_DST_ADDR_ENDP_NOT_PRESENT; + report_attr_cmd.attributeID = ESP_ZB_ZCL_ATTR_PRESSURE_MEASUREMENT_VALUE_ID; + report_attr_cmd.direction = ESP_ZB_ZCL_CMD_DIRECTION_TO_CLI; + report_attr_cmd.clusterID = ESP_ZB_ZCL_CLUSTER_ID_PRESSURE_MEASUREMENT; + report_attr_cmd.zcl_basic_cmd.src_endpoint = _endpoint; + + esp_zb_lock_acquire(portMAX_DELAY); + esp_zb_zcl_report_attr_cmd_req(&report_attr_cmd); + esp_zb_lock_release(); + log_v("Pressure report sent"); +} + +#endif //SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED diff --git a/libraries/Zigbee/src/ep/ZigbeePressureSensor.h b/libraries/Zigbee/src/ep/ZigbeePressureSensor.h new file mode 100644 index 00000000000..f088c033bb9 --- /dev/null +++ b/libraries/Zigbee/src/ep/ZigbeePressureSensor.h @@ -0,0 +1,60 @@ +/* Class of Zigbee Pressure sensor endpoint inherited from common EP class */ + +#pragma once + +#include "soc/soc_caps.h" +#include "sdkconfig.h" +#if SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED + +#include "ZigbeeEP.h" +#include "ha/esp_zigbee_ha_standard.h" + +// clang-format off +#define ZIGBEE_DEFAULT_PRESSURE_SENSOR_CONFIG() \ + { \ + .basic_cfg = \ + { \ + .zcl_version = ESP_ZB_ZCL_BASIC_ZCL_VERSION_DEFAULT_VALUE, \ + .power_source = ESP_ZB_ZCL_BASIC_POWER_SOURCE_DEFAULT_VALUE, \ + }, \ + .identify_cfg = \ + { \ + .identify_time = ESP_ZB_ZCL_IDENTIFY_IDENTIFY_TIME_DEFAULT_VALUE, \ + }, \ + .pressure_meas_cfg = \ + { \ + .measured_value = ESP_ZB_ZCL_ATTR_PRESSURE_MEASUREMENT_VALUE_DEFAULT_VALUE, \ + .min_value = ESP_ZB_ZCL_PATTR_RESSURE_MEASUREMENT_MIN_VALUE_DEFAULT_VALUE, \ + .max_value = ESP_ZB_ZCL_PATTR_RESSURE_MEASUREMENT_MAX_VALUE_DEFAULT_VALUE, \ + }, \ + } +// clang-format on + +typedef struct zigbee_pressure_sensor_cfg_s { + esp_zb_basic_cluster_cfg_t basic_cfg; + esp_zb_identify_cluster_cfg_t identify_cfg; + esp_zb_pressure_meas_cluster_cfg_t pressure_meas_cfg; +} zigbee_pressure_sensor_cfg_t; + +class ZigbeePressureSensor : public ZigbeeEP { +public: + ZigbeePressureSensor(uint8_t endpoint); + ~ZigbeePressureSensor(); + + // Set the pressure value in 1 hPa + void setPressure(int16_t value); + + // Set the min and max value for the pressure sensor in 1 hPa + void setMinMaxValue(int16_t min, int16_t max); + + // Set the tolerance value for the pressure sensor in 1 hPa + void setTolerance(uint16_t tolerance); + + // Set the reporting interval for pressure measurement in seconds and delta (pressure change in 1 hPa) + void setReporting(uint16_t min_interval, uint16_t max_interval, uint16_t delta); + + // Report the pressure value + void report(); +}; + +#endif //SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED diff --git a/libraries/Zigbee/src/ep/ZigbeeTempSensor.cpp b/libraries/Zigbee/src/ep/ZigbeeTempSensor.cpp index 3dfac0489dd..98a3793fbad 100644 --- a/libraries/Zigbee/src/ep/ZigbeeTempSensor.cpp +++ b/libraries/Zigbee/src/ep/ZigbeeTempSensor.cpp @@ -3,6 +3,7 @@ ZigbeeTempSensor::ZigbeeTempSensor(uint8_t endpoint) : ZigbeeEP(endpoint) { _device_id = ESP_ZB_HA_TEMPERATURE_SENSOR_DEVICE_ID; + _humidity_sensor = false; esp_zb_temperature_sensor_cfg_t temp_sensor_cfg = ESP_ZB_DEFAULT_TEMPERATURE_SENSOR_CONFIG(); _cluster_list = esp_zb_temperature_sensor_clusters_create(&temp_sensor_cfg); @@ -103,6 +104,7 @@ void ZigbeeTempSensor::addHumiditySensor(float min, float max, float tolerance) esp_zb_humidity_meas_cluster_add_attr(humidity_cluster, ESP_ZB_ZCL_ATTR_REL_HUMIDITY_MEASUREMENT_MAX_VALUE_ID, &zb_max); esp_zb_humidity_meas_cluster_add_attr(humidity_cluster, ESP_ZB_ZCL_ATTR_REL_HUMIDITY_TOLERANCE_ID, &zb_tolerance); esp_zb_cluster_list_add_humidity_meas_cluster(_cluster_list, humidity_cluster, ESP_ZB_ZCL_CLUSTER_SERVER_ROLE); + _humidity_sensor = true; } void ZigbeeTempSensor::setHumidity(float humidity) { @@ -165,4 +167,11 @@ void ZigbeeTempSensor::setHumidityReporting(uint16_t min_interval, uint16_t max_ esp_zb_lock_release(); } +void ZigbeeTempSensor::report() { + reportTemperature(); + if (_humidity_sensor) { + reportHumidity(); + } +} + #endif //SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED diff --git a/libraries/Zigbee/src/ep/ZigbeeTempSensor.h b/libraries/Zigbee/src/ep/ZigbeeTempSensor.h index d868034280d..2951d4b7628 100644 --- a/libraries/Zigbee/src/ep/ZigbeeTempSensor.h +++ b/libraries/Zigbee/src/ep/ZigbeeTempSensor.h @@ -40,6 +40,12 @@ class ZigbeeTempSensor : public ZigbeeEP { // Report the humidity value void reportHumidity(); + + // Report the temperature and humidity values if humidity sensor is added + void report(); + +private: + bool _humidity_sensor; }; #endif //SOC_IEEE802154_SUPPORTED && CONFIG_ZB_ENABLED