Skip to content

Latest commit

 

History

History
68 lines (58 loc) · 3.75 KB

bluetooth.md

File metadata and controls

68 lines (58 loc) · 3.75 KB
Raw

Bluetooth/BLE Setup and Test Procedure

  • Ensure that BlueZ and related dependency softwares (listed in setup document earlier) are installed on the host
  • BlueZ is example Bluetooth stack used, as it is generally available in Linux. Any other Bluetooth stack can also be used.
  • In following test, Android device was used as a BT/BLE test device. For BLE testing, nRF connect for mobile APP was used.
  • Ensure that hci0 interface is visible. To check that, run hciconfig.
hci0:	Type: Primary  Bus: SDIO
	BD Address: 3C:71:BF:9A:C2:46  ACL MTU: 1021:9  SCO MTU: 255:4
	UP RUNNING PSCAN
	RX bytes:8801 acl:1000 sco:0 events:406 errors:0
	TX bytes:5097 acl:147 sco:0 commands:52 errors:0
  • This interface supports all standard HCI commands. Use standard hci tools to control and configure this interface.
  • Please note that hciconfig might be deprecated in latest stable BlueZ versions. You can use alternatives given by BlueZ.

BT/BLE Test procedure

  • ESP-Hosted related BR/EDR 4.2 and BLE 4.2 functionalities are tested with bluez 5.50+. Whereas BLE 5.0 functionalities are tested with bluez 5.45+.
  • We suggest latest stable bluez version to be used. Any other bluetooth stack instead of bluez also could be used.
  • To upgrade bluez for particular version, follow this link. Replace bluez older version to expected version while following mentioned link.
GATT server

Steps:

  1. Run sudo bluetoothctl.
  2. Run list to get MAC address of ESP.
  3. To set device name, run menu advertise. Then name <enter_any_name>.
  4. To come back to main menu, run back.
  5. To start advertising, run advertise on. Perform below steps on Mobile Phone:
  6. Turn on mobile phone's bluetooth. Open nRF connect application, ESP's MAC address will be displayed under SCANNER tab as a result of scan.
  7. Click on connect. Client tab will be open. Click on Generic Attribute option.
  8. Perform read/write on listed characteristics fields in Generic Attribute service. To disconnet:
  9. Run disconnect <MAC_ADDRESS_of_gatt_client> on linux host's bluetoothctrl OR click on DISCONNECT in nRF connect application's GATT client screen.
GATT Client
  1. Run sudo bluetoothctl.
  2. To Turn on power, run power on.
  3. Make device discoverable, run discoverable on.
  4. Make device pairable, run pairable on.
  5. Set current agent to default, run default-agent.
  6. Turn on bluetooth support, run agent on.
  7. Turn on mobile phone's bluetooth so that linux host can detect it.
  8. Start scanning, run scan on.
  9. Once mobile phone's MAC address is listed in scan list, stop scanning, run scan off.
  10. Start btmon to collect log in separate terminal window, run sudo btmon &.
  11. To trust, run trust <MAC address of mobile phone>.
  12. To pair, run pair <MAC address of mobile phone>.
  13. To connect, run connect <MAC address of mobile phone>.
  14. Once connected, please run discoverable off.
  15. Go to gatt menu, run menu gatt.
  16. list available attributes, run list-attributes.
  17. select characteristic of service, run select-attribute <characteristic_of_service>.
  18. perform read/write operation on selected characteristic.
  19. To disconnect, run disconnect <MAC_ADDRESS_of_gatt_server>.
BT scan
  • Please refrain for using hcitool, as they are deprecated in latest stable releases of BlueZ.
    Alternative tool like sudo buetoothctl with command scan on could be used for BT scan.
BLE scan
  • Please refrain for using hcitool, as they are deprecated in latest stable releases of BlueZ.
    Alternative tool like sudo buetoothctl with command scan on could be used for BT scan.