forked from tmk/tmk_keyboard
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Makefile
132 lines (110 loc) · 4.1 KB
/
Makefile
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
# Target file name (without extension).
TARGET ?= adb_usb
# Directory common source filess exist
TMK_DIR ?= ../../tmk_core
# Directory keyboard dependent files exist
TARGET_DIR ?= .
# project specific files
SRC ?= matrix.c \
adb.c
CONFIG_H = config.h
# MCU name
# atmega32u4 Teensy2.0
# atemga32u4 TMK Converter rev.1
# atemga32u2 TMK Converter rev.2
MCU ?= atmega32u2
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU ?= 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH ?= AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB ?= $(F_CPU)
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096 for TMK Converter rev.1/rev.2
# LUFA bootloader 4096
# USBaspLoader 2048
BOOTLOADER_SIZE ?= 4096
OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE)
# Build Options
# comment out to disable the options.
#
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
CONSOLE_ENABLE ?= yes # Console for debug(+400)
COMMAND_ENABLE ?= yes # Commands for debug and configuration
NKRO_ENABLE ?= no # USB Nkey Rollover
ADB_MOUSE_ENABLE ?= yes # ADB Mouse support
UNIMAP_ENABLE ?= yes # Use unimap
ACTIONMAP_ENABLE ?= no # Use 16bit actionmap instead of 8bit keymap
KEYMAP_SECTION_ENABLE ?= yes # fixed address keymap for keymap editor
# ADB Mice need acceleration for todays much bigger screens.
ADB_MOUSE_MAXACC ?= 8
OPT_DEFS += -DADB_MOUSE_MAXACC=$(ADB_MOUSE_MAXACC)
# Enable scroll wheel functionality using the y-axis of the mouse
# Hold the assigned button down to scroll using the mouse
#
# Example:
# Kensington Turbo Mouse 5
# ________
# middle click -> |3 __ 4| <- scroll toggle (browser back when disabled)
# | / \ |
# | \__/ |
# left click -> |1 2| <- right click
# |________|
#
ADB_MOUSE_SCROLL_BUTTON ?= 4 # Assign the button (1-8) (0 to disable)
ADB_MOUSE_SCROLL_SPEED ?= 10 # 1 (fastest) to 127 (slowest)
# Optimize size but this may cause error "relocation truncated to fit"
#EXTRALDFLAGS = -Wl,--relax
OPT_DEFS += -DADB_MOUSE_SCROLL_BUTTON=$(ADB_MOUSE_SCROLL_BUTTON)
OPT_DEFS += -DADB_MOUSE_SCROLL_SPEED=$(ADB_MOUSE_SCROLL_SPEED)
#
# Keymap file
#
ifeq (yes,$(strip $(UNIMAP_ENABLE)))
KEYMAP_FILE = unimap
else
ifeq (yes,$(strip $(ACTIONMAP_ENABLE)))
KEYMAP_FILE = actionmap
else
KEYMAP_FILE = keymap
endif
endif
ifdef KEYMAP
SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
else
SRC := $(KEYMAP_FILE)_plain.c $(SRC)
endif
# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TMK_DIR)
include $(TMK_DIR)/protocol/lufa.mk
include $(TMK_DIR)/protocol.mk
include $(TMK_DIR)/common.mk
include $(TMK_DIR)/rules.mk