Skip to content

Latest commit

 

History

History
124 lines (89 loc) · 5.63 KB

README.md

File metadata and controls

124 lines (89 loc) · 5.63 KB

TurboCAN

Image of TurboCAN board

This is the official repository for the TurboCAN controller board, designed specifically for the Voron AfterBurner toolhead but can also be used on similar toolheads using NEMA17 steppers. The main benefit of this board is the capability to run the toolhead over just 4 wires (CAN, +24V, Ground) which greatly simplifies the wiring in the Voron v1 and v2 models.

Features

  • 1x Combined CAN-bus and 24V power port with polarity protection
  • 1x ADXL345 accelerometer for use with Klipper's input shaper feature
  • 1x 24V stepper stick mount and motor output
  • 3x 24V MOSFET fan0/fan1/heater outputs (up to 3A)
  • 2x 5V powered endstop inputs (marked X/Y), could be used for toolhead mounted endstops (microswitch or hall effect), filament runout sensor or 5V Z probe.
  • 1x 24V powered endstop input (marked Z) with built-in BAT42 diode, used for inductive probe on the AfterBurner but also supports microswitch based probing (e.g. Magprobe).
  • 1x Thermistor input with 4.7k pullup resistor
  • 1x USB-C port
  • 1x SWD debug port with BOOT0/RESET broken out
  • 5V 3A buck converter (available externally on X/Y endstops) and 3.3V 200mA linear regulator (internal only)
  • Power LED & Activity (PA1) LED

The board supports interfacing with Klipper both over CAN and USB-C (selectable when building the Klipper firmware).

Use cases

The TurboCAN board is actually not only useful as a toolhead board, here are some reasons why you want more of them:

  • Want even less wiring? TurboCAN fits on the back of any NEMA17 stepper, so you can mount TurboCAN boards on e.g. the A/B (or X/Y) steppers and run them over a shared CAN bus.
  • Need a USB to CAN interface? TurboCAN can do USB and CAN at the same time, so you can flash CandleLight firmware and use it as a USB-CAN interface.
  • Want input shaper but annoyed by the complicated SPI wiring needed for the ADXL345 board? Just use a spare TurboCAN board over USB(/CAN) instead.

Current status

WARNING: While the author has a working printer running a TurboCAN v0.1 board, this project is in early development, and most likely still has undiscovered issues. Build one at your own risk!

  • v0.1 boards ordered
  • v0.1 boards testing
    • LEDs
    • 3.3v LDO
    • SWD debug port
    • USB interface
    • Buck converter
    • Stepper stick
    • MOSFET outputs
    • CAN-bus + Flashing Klipper (CAN)
    • Thermistor input
    • X/Y endstop inputs
    • Z endstop input

Getting started

  1. Configure Klipper using make menuconfig:

Klipper menuconfig

  1. Put a jumper between BOOT0 and 3.3V and power cycle the board.

  2. Flash the TurboCAN board using make flash FLASH_DEVICE=1234:ABCD (replace USB vendor/product, you find them with lsusb).

  3. Connect the TurboCAN board using your favorite CAN bus interface (or use another TurboCAN board, see below).

  4. Run the klipper/scripts/canbus_query.py command to determine the CAN address. See Klipper docs for more info.

  5. Use the provided Klipper config as a starting point.

Changelog

v0.2

  • Errata fixes
    • LEDs are now mounted the right way.
    • R11 connected to R10/VSENSE.
    • SPI bus to the ADXL345 now have MISO/MOSI on the right pins.
    • Z probe input now has filtering and pullup resistor.
    • Reworked buck converter compensation circuitry.
    • Added CAN termination resistor.
  • Added 100uF bulk capacitor for 24V to mitigate voltage fluctuations due to long cables.
  • Thermistor resistor is now in 0805 package (was 0402) to simplify replacement to 1k (for PT1000 sensor).
  • Improved filtering of analog power domain to reduce ADC noise.
  • Replaced the heater mosfet with a more powerful AON7400A.
  • Replaced the +3.3V connection to MS1 with an unpopulated resistor to give the board UART address 0 by default.
  • Added optional pullup resistors to MS2/SPREAD to support standalone mode for the step stick.

Errata

v0.1

  • LEDs are mounted backwards.
    • Workaround: Reverse them (or simply skip, they aren't essential).
  • R11 not connected to R10/VSENSE.
    • Workaround: Simple to bodge as R10 is next to it.
  • MISO and MOSI are swapped on the SPI bus to the ADXL345.
    • Workaround: Use software SPI.
  • Z probe input lacks filtering and pullup resistor
    • Workaround: Use MCU internal pullup.
  • Higher than optimal noise from the buck converter leading to noisy accelerometer readings.
    • Workaround: Doesn't need one, performance is still good enough for input shaper.
  • No CAN termination resistors on-board
    • Workaround: Mount a 0603 120Ohm resistor between the H/L legs of the CAN JST-XH connector on each end of the bus.
  • Thermistor readings are noisy (fluctuating 2-3C) with a PT1000 sensor
    • Workaround: Use a B3950 or replace the pullup resistor with a 1k 0.5%

Developer Info

Generating fabrication outputs for JLCPCB

  1. Export Gerbers and drill file from pcbnew, make a zip file out of these.
  2. Generate a BOM csv using bom_csv_jlcpcb.py from kicad-jlcpcb-bom-plugin.
  3. Generate a CPL file from pcbnew.
  4. Convert the CPL file to JLCPCB format using using kicad_pos_to_cpl.py from kicad-jlcpcb-bom-plugin.

Attribution

Although this was designed from scratch, it was inspired by the Huvud board made by Pontus Borg.

License

For compability with other Voron projects, all included files are licensed under the GNU GPL-3 license.