Skip to content

Releases: hpmicro/hpm_sdk

v1.7.0

30 Sep 07:40
Compare
Choose a tag to compare

[1.7.0] - 2024-09-30:

Main changes since 1.6.0
Tested Segger Embedded Studio Version: 8.16a
Tested Zcc toolchain 3.2.4

Changed:

  • soc: HPM6E00: HPM6E80: add tsw section
  • soc: add hpm_otp_table.h
  • soc: enet: add a macro for DMA bus width
  • soc: system.c: set bpor.por_confing retention bit to avoid bgpr data loss
  • soc: pcfg: add pcfg_wakeup_src_t enum and pcfg_update_periph_clock_mode API
  • soc: hpm5300: exclude fgpio region from dlm
  • soc: add CONFIG_ENABLE_BPOR_RETENTION macro to control bpor retention
  • soc: linker: icf: update cherryusb_usbh_class_info section placement
  • soc: HPM6300/HPM6700: delete pcfg_dcdc_set_current_hys_range() API
  • ip: i2s: add and use clk_i2s_src_audn instead of clk_i2s_src_aud0/1/2/3
  • boards: remove hpm6750evk support
  • boards: hpm6e00evk: update femc pinmux
  • boards: pinmux: set max frequency slew rate for SPI GPIO
  • boards: hpm5301evklite: Change cap1 and comp1 pins of gptmr0
  • boards: hpm5301evklite: change i2c2 to i2c3 for BOARD_APP_I2C
  • boards: add board_init_gptmr_channel_pin API for all board
  • boards: hpm6e00evk: update core1 debugger console readme
  • boards: all: add board_init_acmp_pins API
  • boards: hpm6800evk: adc16: update clock bus name for clock initialization
  • boards: adc16: rename api parameter clk_src_ahb to clk_src_bus
  • boards: add BOARD_APP_ADC16_CLK_BUS definition
  • boards: hpm6e00evk: update board readme
  • boards: hpm6e00evk: bump up DCDC voltage to 1250mv
  • boards: add enet pps input feature and pinmux setting API
  • boards: add missing board feature and pin descriptions for enet pps output pin
  • boards: xxxx.yaml: rename board feature name related to enet pps pin
  • boards: add BOARD_MASTER_I2S and BOARD_SLAVE_I2S
  • boards: add board mic and speaker i2s definition
  • boards: doc: pwm: add pwm pin descriptions.
  • boards: hpm6800evk reduce ddr io leakage.
  • boards: hpm6800evk: pps: adjust pinmux settings
  • drivers: tsw: optimize the logic of sending and receiving APIs
  • drivers: tsw: add APIs for speed, interface, and clock delay settings
  • drivers: tsw: split tsw_ep_enable_mac_ctrl API to two APIs for enableing and disabling
  • drivers: usb: update usb phy init for suspend
  • drivers: qeiv2: update comments
  • drivers: i2c: auto ack needs to be enabled after the transmission is completed for i2c_master_transfer API
  • drivers: adc16: split adc16_set_pmt_queue_enable() into enable and disable API
  • drivers: gptmr: add opmode cntmode monitor configuration member for gptmr_channel_config API
  • drivers: spi: add the judgment that the frequency ratio cannot be greater than 510 for spi_master_timing_init API
  • drivers: enet: add retry logic in DMA initialization
  • drivers: spi: Add slave mode judgment for spi_control_init API
  • drivers: spi: add spi busy state judement for transfer APIs
  • drivers: uart: add disable rx timeout trigger dma function
  • drivers: i2s: add buff data align with frame feature
  • drivers: acmp: add acmp_channel_config_cap_selection
  • drivers: acmp: update acmp_channel_config_dac API
  • drivers: usb: update usb phy init and deinit
  • drivers: enet: add auxiliary snapshot APIs and struct definitions
  • drivers: usb: update usb_force_port_resume() annd add usb_hcd_disable_ase_pse() APIs
  • drivers: tsw: update the prefix of apis starting with tsn to tsw
  • drivers: qeiv2: update qeiv2_config_adcx_adcy_param()
  • drivers: usb: update usb_hcd_disable_ase_pse() & usb_hcd_enable_ase_pse()
  • components: enet_phy: rtl8211: optimize logic for initialization config
  • components: ppi: add assert check for cs_index and cmd_start_index
  • components: ppi: update AD-MUX mode config to decrease address latch
  • components: smbus: i2c_master_write replaces i2c_master_transfer for all smbus write APIs
  • components: serial_nor: Added configuration return judgment for transfer API
  • components: serial_nor: judge DMA sending completion for hpm_spi_transfer_via_dma API
  • components: spi: add spi busy state judgment for hpm_spi_transfer_init API
  • components: i2s_over_spi: add hpm_i2s_master_over_spi_tx_buffer_nonblocking API
  • components: i2s_over_spi: optimized hpm_i2s_master_over_spi_tx_stop API
  • components: i2s_over_spi: add hpm_i2s_master_over_spi_tx_is_busy API
  • middleware: hpm_math: support zcc new version
  • middleware: cherryusb: update to v1.4.0
  • middleware: lwip: CMakeLists.txt: add cmake flag for apps
  • middleware: cherryusb: don't clean csc bit when init
  • middleware: cherryusb: msc host: support multi msc device
  • middleware: fatfs: cherryusb: support two msc device
  • middleware: reduce netx mem usage
  • middleware: cherryusb: host: update usb_hc_deinit()
  • middleware: usbx: host: delete mode setting in usb_host_mode_init()
  • middleware: hpm_sdmmc: sdcard: added retransmission to improve SPI SD card compatibility
  • middleware: tinyengine: rename old function
  • samples: audio_codec: change default codec setting in CMakeLists.txt
  • samples: adc16 & motor_ctrl: update adc16 preemption queue enable control APIs
  • samples: ppi: parallel_adc: update function name
  • samples: ppi: async_sram: update to support AD Mux Mode
  • samples: lwip & modbus: add judgement for the return value of enet controller initialization
  • samples: lwip: lwip_iperf: exclude flahsh_uf2 & flash_uf2_release targets
  • samples: lwip: add conditional compilation for RMII port
  • samples: cherryusb: msc host: adapter to fatfs update
  • samples: drivers: acmp: replace init_acmp_pins API with board_init_acmp_pins API
  • samples: ecat: read mailbox ram buff by ram alias address
  • samples: ecat: set PHY offset
  • samples: ecat_phy: disable PHY addr 00 broadcast response
  • samples: drivers: adc16: reference APP_ADC16_CLOCK_BUS instead of clk_adc_src_ahb0
  • samples: ecat_io: update flash_eeprom data address
  • samples: ecat: update SSC config xml and ESI xml
  • samples: lwip: ports: rtthread-nano: single&multiple: add sys_arch_protech()/sys_arch_unprotect()
  • samples: power_mode_switch: move sysctl_enable_cpu0_wakeup_source_with_irq() to stop mode settings
  • samples: power_mode_switch: keep puart clock and wakeup enable visible
  • samples: acmp: add a macro TEST_ACMP_DAC_MAX_VALUE for better compatibility
  • samples: drivers: enet: pps: app.yaml: rename dependency
  • samples: ppi: parallel_adc: use macro BOARD_PPI_ADC_CS_INDEX
  • samples: i2s: use BOARD_MASTER_I2S and BOARD_SLAVE_I2S
  • samples: audio_codec: use board speaker macros
  • samples: cherryusb: audio: use board mic and speaker macros
  • samples: lwip & cherryusb/host/usbnet: use the external struct timeval definition from compile system
  • samples: esc: update esc read to 32bit access
  • samples: ecat_foe: update log and README
  • samples: ecat_foe: foe flash read cache maintenance
  • samples: ppi: use macros to select pins
  • samples: drivers: gptmr: cntmode: volatile to key parameter variables to prevent them from being optimized
  • samples: spi_sdcard: Added delay function registration
  • samples: cherryusb: mouse_wakeup: update printf log
  • samples: cherryusb: midi: update readme
  • samples: i2s: change HDMA to XDMA
  • samples: tflm: optimized speed.
  • samples: tflm: add zcc compile options.
  • samples: spi_component: full_duplex: Add known issues in the master readme
  • samples: spi_components: half_duplex: reduce SPI SCLK frequency to adapt to different slave boards
  • samples: spi_components: full_duplex: reduce SPI SCLK frequency to adapt to different slave boards

Fixed:

  • soc: HPM6800: HPM6880: fix the clock bus name for wdg
  • soc: SPI_SOC_TRANSFER_COUNT_MAX Definition error for HPM6E00
  • soc: preserve kept symbols while -flto is enabled
  • soc: hpm6880: fix clk bus name for adc from ahb0 to axis0
  • soc: HPM6300: fix get get_frequency_for_i2s_or_adc() problem
  • soc: HPM6700: fix clock_set_i2s_source() check condition
  • soc: romapi: Fix unexpected data fetch error during flash init/write.
  • soc: linker: gcc: fix fast_ram postion
  • boards: hpm5301evklite: add a missing macro BOARD_APP_ADC16_CLK_BUS
  • boards: i2c init: clock_add_to_group() should be before board_i2c_bus_clear()
  • boards: hpm6800evk pinmux PRS set wrong value
  • boards: hpm6750evkmini: fixed the iomux errata causes the slave to not work issue
  • boards: hpm6750evk2: fixed the iomux errata causes the slave to not work issue
  • boards: hpm6750evkmini: add the missing implement of enabling enet irq
  • boards: hpm6750evkmini: fix touch reset timing.
  • drivers: i2c: correct API name
  • drivers: gptmr: fix cmp value can't set 0xFFFFFFFF problem
  • drivers: pwmv2: fix counter burst set error.
  • drivers: enet: fix return value of enet_dma_init()
  • drivers: usb: fix usb_dcd_remote_wakeup() api
  • drivers: enet: fix enet max frame size
  • drivers: spi: Fixed mode variable assignment error for spi_slave_get_default_format_config API
  • drivers: i2s: fix fill dummy data in slave mode
  • drivers: adc16: fix ADC16 conversion results in single-ended mode
  • drivers: enet: fix that TSIS interrupt is disabled by default
  • drivers: femc: fix cmd_data_width comment error
  • drivers: spi: fixed offset digit error problem for spi_get_rx_fifo_valid_data_size and spi_get_tx_fifo_valid_data_size APIs
  • drivers: spi: fixed possible packet loss during reception for spi_read_data API
  • drivers: usb: fix phy init for host
  • drivers: touch: gtxx: fix reset timing
  • drivers: mipi dsi: fix bandwidth low
  • drivers: mcan: fix wrong offset in can_rx_message_t.
  • drivers: adc12: fix using a wrong calibration value
  • components: ppi: fix config variable init value
  • components: serial_nor: Fixed the nonblock APIs naming error
  • components: serial_nor: spi: fixed formating issue...
Read more

v1.6.0

28 Jun 00:42
Compare
Choose a tag to compare

[1.6.0] - 2024-06-28:

Main changes since 1.5.0
Tested Segger Embedded Studio Version: 8.10d
Tested IAR Embedded Workbench for RISC-V Version: 3.30.1

Known Issue:

  • some IAR projects does not work properly when optimization level is increased

Changed:

  • soc: reorganize the directory structure
  • soc: hpm6750: declare get_frequency_for_source API for clock drver header file
  • soc: update soc cmakelists to add b ext info
  • soc: hpm6750: add feature for ioc pad ctrl setting issue
  • soc: toolchains: gcc: correct LMA for NOLOAD sections
  • soc: move eh_frame into separate section
  • boards: hpm6750xxxx apply workaround for E00029.
  • boards: change hpm5301evklite adc16 channel
  • boards: board.h: adc16: add marco BOARD_APP_ADC16_HW_TRIG_SRC_CLK_NAME
  • boards: adjust function position of adc pin initialization
  • boards: hpm6300evk and hpm6e00evk: sdram use px07 as femc dqs pin
  • boards: hpm6e00evk: rename init_sdram_pins to init_femc_pins
  • boards: hpm6e00evk: change board i2c instance to I2C0
  • drivers: can/mcan add parameter check for low-level bit timing.
  • drivers: enet: add bitfield ENET0_RMII_TXCLK_SEL for hpm6300
  • drivers: i2c: add DATACNT high byte process
  • drivers: pwm: update HRPWM process
  • drivers: spi: optimize reading speed for spi_read_data API
  • drivers: spi: add set/get data phase format APIs for spi master
  • drivers: spi: delete the spi startand operation APIs
  • drivers: adc16: remove an unused member conv_duration from adc16_config_t
  • drivers: enet: update for enet_interrupt_enable_t
  • drivers: mcan reduce unnecessary register access in mcan_read_rxfifo.
  • drivers: mtg: add calculate function param clock
  • drivers: mtg: add several calculate functions
  • drivers: mcan lookeup the mcan msg ram base via mcan_soc_msg_buf variable if the MSG_BUF is in AHB RAM.
  • drivers: adc16: disable improvement logic of adc16 for continuous sampling maximum voltage
  • drivers: mcan improve transmitter delay compensation setting logic.
  • drivers: femc: rename data_width_in_byte to cmd_data_width
  • drivers: femc: update ns2cycle() to align up
  • drivers: common: add packed attribute
  • drivers: femc: delete duplicate config
  • drivers: mtg: change the default parameters to the low order filter
  • drivers: adc16: add API adc16_set_seq_hw_trigger_enable()
  • drivers: spi : convert enumeration return in that gets parameters APIs
  • drivers: pwm: add fault recovery code.
  • driver: pwm: change pwm trig time
  • components: enet_phy: dp83867/rtl8211: move the macro definition RGMII to board-level CMakeLists.txt
  • components: eeprom_emulation: Add ATTR_RAMFUNC for all function
  • components: eeprom_emulation: add power-off protection mechanism.
  • components: dma_mgr: add burst in fixed transfer size and swap feature
  • components: spi: add full_duplex and half_duplex operating APIs
  • components: spi: support 1 to 32 bits width transfer for nonblocking APIs
  • components: usb: device: support iso transfer mult feature
  • middleware: hpm_sdmmc add emmc sleep & wakeup function.
  • middleware: tinyusb: ehci: support chain transfer
  • middleware: threadx: add low power support
  • middleware: cherryusb: update for advance descriptor
  • middleware: hpm_sdmmc: optimized to support multiple cards
  • middleware: cherryusb/tinyusb/usbx: enable suspend isr
  • middleware: FreeRTOS: update to 202210.01 lts
  • middleware: cherryusb: update to v1.3.0
  • middleware: freertos: modify missed timer count num
  • middleware: freertos: update IAR port file
  • middleware: freertos: delete fence operations
  • middleware: freertos: make the calculation more simple.
  • middleware: hpm_sdmmc add cache control macro.
  • middleware: hpm_sdmmc: improve the logic for detecting CMD23 support.
  • middleware: freertos: add tickless stop mode support
  • middleware: freertos: add user custom process function call
  • middleware: hpm_mcl_v2: add hpm smc control.
  • middleware: freertos: place xPortxxx to isr_vector section
  • middleware: hpm_math: add dsp support for zcc
  • middleware: microros: add zcc support
  • middleware: rtos: asm adjustment for zcc toolchain
  • middleware: hpm_mcl_v2: add pwm dead area compensation.
  • middleware: hpm_mcl_v2: add dq axis decoupling function
  • middleware: cherryusb: add macro USBH_USE_CUSTOM_ISR/USBD_USE_CUSTOM_ISR
  • middleware: lvgl: upgrade to v9
  • middleware: lvgl: rewrite the scissor.
  • middleware: lvgl: upgrade allocate algorithm for draw_buf.
  • samples: rdc: remove unused dac driver in sample
  • samples: lwip/netxduo/modbus: add conditional compile for reference clock setting in RMII mode
  • samples: audio_codec: common: change FIL_SEARCH_NUM from 10 to 20
  • samples: dhyrstone: surpress build warnings
  • samples: dhrystone Optimize performance.
  • samples: coremark Optimize performance.
  • samples: drivers: spi: interrupt: transmission optimization. The transmission will start after the configuration is completed.
  • samples: adapt spi components to drive and move to the samples dir for spi sdcard samples
  • samples: cherryusb: device: change descriptor string to HPMicro
  • samples: cherryusb: device: use advanced descriptor to support high/full speed
  • samples: rename jpeg to image
  • samples: drivers: sdxc: sd_fatfs: add card hotplug support
  • samples: cherryusb: host: usbnet: replace block to noblock for read terminal char
  • samples: cherryusb: host: usbnet: decrease lwip MEM_SIZE
  • samples: cherryusb: move host hid info print code to thread
  • samples: audio_codec: refactoring code
  • samples: spi: dma: SPI master transmission optimization
  • samples: mtg: make the open_loop_trajectory sample more readable
  • samples: drivers: adc16: add some misc optimization
  • samples: drivers: adc16: add pwmv2 support
  • samples: motor_ctrl: bldc_foc_hw: remove hardware control
  • samples: drivers: mcan add tips for the usage of tdc.
  • samples: vglite: update rtos config file to fit gptmr tickless mode
  • samples: lwip/modus/netxduo: add a function call to get the enet default interrupt config
  • samples: sdm: using pwm to provide clock for sdm sensor.
  • samples: spi_components: half_duplex: updated to support 1 to 32bits width transfer
  • samples: spi_components: full_duplex: updated to support 1 to 32bits width transfer
  • samples: add freertos tickless stop mode sample
  • samples: benchmark: update compile options for zcc
  • samples: drivers: adc16: optimize the process logic of sequence and preemption
  • samples: drivers: sei: device: tamagawa: update eeprom cmd
  • samples: adc12: optimization for trigger mux and trigger frequency settings
  • samples: sei: device: tamagawa: support EEPROM protocol
  • samples: mcl: add pwm dead area compensation.
  • samples: motor_ctrl: add dq axis decoupling function
  • samples: cherryusb: move dual_port samples to dual_port folder
  • samples: cherryusb: adapter to cherryusb v1.3.0
  • samples: drivers: adc12/adc16/dac: support abort feature in interactive terminal
  • samples: lwip: lwip_iperf: support abort feature to reselect the test mode
  • samples: lwip: common: multiple: add definitions of remote ip addresses for iperf
  • samples: motor_ctrl: bldc_lvlg_foc: add lvgl v8.3.5 for this demo
  • samples: tinyusb: uac2: support full speed
  • samples: power_mode_switch: update readme
  • samples: cherryusb: uac2: change default samplerate order
  • samples: bldc_foc: update bldc_foc_angle_align() for hardware loop
  • cmake: toolchain: add ar option to remove timestamp
  • cmake: toolchain: suppress output while querying spec
  • cmake: lld: update link option for zcc
  • cmake/scripts/soc: support b ext convertion to tools
  • cmake: sdk_app_src_glob: modify to recursive

Fixed:

  • soc: update USE_NONVECTOR_MODE defined used
  • soc: initialize .fast_ram.* section
  • soc: iar linker: fix safe stack init
  • soc: add missing ptmr clock
  • soc: hpm6880: fix get_frequency_for_i2s error
  • soc: hpm6880: Modify the value of SPI_SOC_FIFO_DEPTH from 4 to 8. for hpm_soc_feature.h
  • soc: toolchain: iar fix iar ram_stress issue in ram_debug build.
  • boards: hpm5301evklite: fixed can't output work for gptmr samples such as pwm_generate
  • drivers: enet: fix the clearing of DMA PBL setting
  • drivers: dma: fix dma_clear_transfer_status() API
  • drivers: sdxc Fix timeout calculation issue and DMA enabling logic.
  • drivers: adc16: fix the logic of adc16_set_pmt_queue_enable() when the parameter enable is false
  • drivers: mbox: fix error that BEIE can't be operated by interface
  • drivers: spi: fixed assignment value error for spi_set_clock_phase and spi_set_clock_polarity APIs
  • drivers: lcdc: fix ST and DMA_ST clear api.
  • drivers: mipi_dsi: fix MIPI_DSI_FMT_RGB565 config.
  • drivers: spi: fixed assignment error issue for enable/disable address phase APIs
  • drivers: i2c: fix return value type of i2c_get_data_count()
  • components: usb device/enet_phy: fix unwanted files in localize folder
  • components: panle: fix panel timing.
  • components: eeprom_emulation: demo flash crashed.
  • middleware: cherryusb: ehci: delete timeout clear before give sem
  • middleware: uC/OS-III: modify fpu context save&restore
  • middleware: cherryusb: fix freertos enter/exit critical
  • middleware: audio_codec: fix hpm_wav_decode() single channel pbuf data
  • middleware: mclv2: fix andes toolchain compiler error.
  • middleware: cherryusb: fix ehci_qh_pool init miss busid for v1.3.0
  • middleware: lwip: apps: lwiperf: fix the bug of failing to restart iperf in TCP/UDP server mode
  • middleware: tinyusb: fix _usbd_dev.speed error to support full speed
  • middleware: hpm_mcl_v2: fix uncontrolled after large changes in motor speed.
  • samples: dhyrstone: fi...
Read more

v1.5.0

29 Mar 07:58
Compare
Choose a tag to compare

[1.5.0] - 2024-03-29:

Main changes since 1.4.0

Tested Segger Embedded Studio Version: 7.32a
Tested IAR Embedded Workbench for RISC-V Version: 3.20.1

Known Issue:

  • some IAR projects does not work properly when optimization level is increased

Changed:

  • soc: iomux: update macro prefix in pmic_iomux and batt_iomux.
  • soc: feature: change usb endpoint max number from 8 to 16
  • soc: correct svd files and add subpart module list
  • drivers: usb: change usb_phy_get_line_state() to external function
  • drivers: qeiv2: update filter length setting
  • drivers: adc12/adc16: add sanity check for sample cycle
  • drivers: femc: add delay_cell_disable config option
  • drivers: i2s: change fifo threshold parameter.
  • drivers: i2c: replace and use the macro definition of hpm_soc_ip_feature.
  • drivers: uart: supplementary description of uart_check_status API.
  • components: enet_phy: lan8720/rtl8201/rtl8211: unify the default config with type bool
  • components: enet_phy: remove unused included header file
  • components: enet_phy: rtl8201/rtl8211: update register description
  • components: dma_mgr: change isr handler from static to public
  • middleware: tinyusb: host: use echi drivers
  • middleware: tinyusb: rename CFG_TUSB_HOST_DEVICE_MAX to CFG_TUH_DEVICE_MAX
  • middleware: tinyusb: update to v0.16
  • middleware: rtthread-nano: use soc reset_handler and define MAIN_ENTRY as entry
  • middleware: fatfs: tinyusb: adapter to tinyusb update
  • middleware: threadx: use TX_TIMER_TICKS_PER_SECOND to config work ticks
  • middleware: threadx: use samples tx_user.h
  • middleware: uC/OS-III: enable sw interrupt in OSCtxSw/OSIntCtxSw
  • middleware: ucos: ports: Added IAR portable layer for ucos.
  • middleware: cherryusb/azure_rtos: add defined ICCRISCV for iar
  • middleware: hpm_math: simplify libdsp path.
  • middleware: cherryusb: update to v1.1.0
  • middleware: rtthread-nano:halt cpu when exception occur.
  • middleware: hpm_math: simplify libnn path.
  • middleware: threadx: move frequently called function to ram.
  • middleware: tinyusb: change endpoint number from 8 to 16
  • middleware: usbx: change endpoint number from 8 to 16
  • middleware: cherryusb: msc device: update to support multi lun and deinit
  • middleware: eclipse_threadx: update license
  • middleware: fatfs: tinyusb: add osal_task_delay() when use rtos wait
  • middleware: tinyusb: update CMakeLists.txt and delete custom osal_task_delay()
  • middleware: tinyusb: add debounce in port change isr
  • samples: erpc: add middleware src use middleware CMakeLists.txt
  • samples: multicore: core1: use board_init_core1() API
  • samples: multicore: coremark: delete custom reset_handler and use app_main as MAIN_ENTRY
  • samples: tinyusb: update samples to adapter tinyusb v0.16
  • samples: usbx: host: delete unused hpm_usb_host.h
  • samples: usb: delete CONFIG_USB_HOST set
  • samples: lvgl_coremark: disable freqswitch_btn when coremark running
  • samples: mono: move to driver directory.
  • samples: freertos: change configMAX_PRIORITIES from 7 to 32
  • samples: rtthread: delete unused macro RT_THREAD_PRIORITY_32
  • samples: cherryusb: usbnet: decrease rtos stack config size
  • samples: lwip: all: unify logs about IP information
  • samples: lwip: lwip_https_server: remove an unused file
  • samples: lwip: all: update DHCP progress logic
  • samples: lwip: common: remove s_pxNetIf
  • samples: lwip: adjust the directories of netconf.c/netcof.h
  • samples: lwip: common: optimize speed for getting IP from DHCP server
  • samples: lwip: rename common_lwip.c to common.c
  • samples: lwip: common: adjust the call logic of netif_set_up/netif_set_down
  • samples: lwip: common: change the time of invoking netif_user_notification
  • samples: lwip: common: rename user_notification to netif_user_notification
  • samples: lwip: adjust directory structures to be compatible with single and multiple network ports
  • samples: use generate_ide_projects for new samples
  • samples: cherryusb: device: cdc acm: reorganize directory structure
  • samplse: gptmr: t_shape_accel_decel: modify the source address mode of DMA.
  • samples: cherryusb: device: change readbuf size from 2048 to CDC_MAX_MPS
  • samples: drivers: femc: update sdram dqs config
  • samples: update app.yaml to use ip_feature
  • samples: drivers: uart: change to app uart
  • samples: audio_codec: update wm8960 I2S protocol.
  • samples: drivers: cam: change cam sample to cam_dvp sample.
  • samples: usbx: device: msc: decrease ram disk size to 16KB
  • samples: cherryusb: msc device: update to support multi lun
  • samples: driver: uart_lin: support LIN transceiver on board.
  • samples: adc: temp: rename temp to adc16_temperature
  • samples: bldc block: Compatible with both hall and qeiv2 peripherals.
  • samples: motor_ctrl: Modify the value of pwm reload.
  • samples: lwip: common: single/multiple: update the size passed into sys_mbox_new()
  • samples: lwip: common: single/multiple: replace enet_get_link_status with netif_is_link_up
  • samples: lwip: lwip_https_server: remove unused header file
  • samples: lwip: rename macro TCP_XXX_PORT
  • samples: lwip: add cmake flag for netconn/socket api
  • samples: decode_wav: sd_fafts: update sd_choose_music.
  • samples: power_mode_switch: maintain xpi0 clock on switching preset
  • samples: dhrystone Change the optmization level to O3.
  • samples: tinyusb: hid_generic_inout: delete redundant image
  • samples: power_mode_switch: hpm67/hpm63: preserve femc clock at wait/stop mode
  • samples: erpc: core1: use optimization -os
  • samples: update uart_tamagawa to use software trig if TRGM not exist.
  • samples: eeprom_emulation: reduce management area
  • samples: sdxc: use block_size instead of 512
  • samples: erpc: add -fno-exceptions compile option
  • samples: tinyusb: disable debug log print
  • boards: hpm5300evk and hpm6800evk: add delay after USB_PWR Pin init for power stable
  • boards: hpm6750evkmini: modify gptmr pins.
  • boards: hpm6200evk: modify gptmr pins.
  • boards: hpm6200evk: modify the i2c pins.
  • boards: hpm6750xxx: update sdram dqs config
  • boards: hpm6800evk:pinmux Increase drive strength for sdxc pins
  • boards: iomux: update macro prefix for pmic_iomux and batt_iomux.
  • boards: rename board feature
  • boards: update BOARD_APP_UART definition
  • boards: rename console definitions
  • boards: hpm5301evklite: update uart clock in board.c.
  • boards: hpm6750evkmini: change BOARD_GPTMR_PWM_DMA_SRC definition.
  • docs: samples: use glob in high level readme.
  • docs: update top level readme.
  • docs: netxduo: update sntp readme.
  • docs: threadx: update threadx hello readme.
  • docs: lwip: align pictures to the left
  • docs: pip: add cmake doc dependency
  • docs: add changelog to sphnix-doc.
  • scripts: ses: generate asm after build by default.
  • scripts: update linked project path logic.
  • scripts: check_board_cap.py: check ip feature's availability
  • cmake: remove CMP0116 setting.
  • cmake&scripts: clarify the error caused by core1 compiling failure.
  • scripts: ses/iar: use relpath in project file

Added:

  • soc: hpm6360/hpm6750/hpm6800: add MAC-related definitions in OTP section
  • soc: reset: add MAIN_ENTRY macro to custom define main entry
  • soc: add hpm6850 and hpm6830 part.
  • soc: soc_modules.list: add tamper drivers
  • soc: Add IAR toolchain support.
  • soc: add ip feature to soc_modules.list
  • soc: add hpm_soc_ip_feature.h
  • soc: driver: ppor: add reset hold operation APIs
  • soc: clock_driver add the clock_get_divider API.
  • soc: sysctl: add apis to control clock preservation
  • soc: toolchains: gcc: ram linker: add ILM last address overflow check
  • drivers: mcan Add timeout counter support.
  • drivers: tamper: add tamper driver
  • drivers: cam: add cam_update_buffer2 API
  • drivers: opamp: Add user configuration code.
  • drivers: lcdc: add stride for layer config.
  • drivers: pdma: add pdma_blit_ex.
  • drivers:pllctl add out-of-bound check in pllctl driver.
  • components:uart_lin: add hpm_uart_lin_send_wakeup() API
  • components: enet_phy: add LAN8720 driver
  • components: enet_phy: add definition of enet_phy_link_status_t
  • middleware: cherryusb: host: add dual port support
  • middleware: cmsis_os2: adapter to rtthread wrapper
  • middleware: cmsis_os2: update freertos files
  • middleware: cmsis_os2: adapter to threadx wrapper
  • middleware: cmsis_os2: adapter to ucOS-III wrapper
  • middleware: hpm_sdmmc Add eMMC config partition API.
  • middleware: cherryusb Add IAR toolchain support
  • middleware: erpc Fix IAR RISC-V support issue
  • middleware: tflm: add IAR riscv support in flatbuffer
  • middleware: FreeRTOS: portable:Added IAR portable layer.
  • middleware: segger_rtt Added EWRISCV support
  • middleware: hpm_math Add nds_dsp library for IAR.
  • middleware: lwip: cc: add PACK_STRUCT_XXX definitions for IAR platform
  • middleware: uC/OS-III: enable plicsw in IAR asm code
  • middleware: add tinyengine
  • middleware: threadx: add support for gptmr.
  • middleware: threadx: add profile support.
  • middleware: add agile_modbus.
  • middleware: add cherryrb.
  • middleware: cherryusb Add missing swap32/swap16 implementation.
  • middleware: hpm_mclv2: add block type drive motors
  • middleware: cherryusb: fix usbh_core ep0 buffer index
  • boards: hpm6200xxx and hpm6750xxx: add board_init_core1() API
  • boards: add tamper feature and pins init
  • boards: hpm5300evk: add board_init_console() declaration in board.h
  • boards: hpm6750evk/hpm6750evk2: add board_dual_usb feature
  • boards: openocd: add windows guide to *_all_in_one.cfg
  • boards: openocd: soc: add reset_soc proc
  • board:add pgpio configuration on hpm5301evklite
    ...
Read more

v1.4.0

28 Dec 07:19
Compare
Choose a tag to compare

[1.4.0] - 2023-12-29:

Main changes since 1.3.0

Tested Segger Embedded Studio Version: 7.32

Changed:

  • soc: hpm5301: add hpm5301
  • soc: hpm6880: add hpm6880
  • soc: HPM6750: pcfg: update dcdc dcm mode config
  • soc: clock driver: update clock_set_source_divider() and clock_get_source()
  • boards: add hpm5301evklite
  • boards: add hpm6800evk
  • boards: update clock_set_source_divider() to use clk_src_t type param
  • boards: hpm6750evkmini: use the same uart port as core1 for some samples.
  • drivers: dao: update driver support new feature on hpm6800
  • drivers: adc16: update comment about cal_avg_cfg in calibration
  • drivers: qeiv2: change adc trigmux name x to 0 and y to 1
  • drivers: femc: add overflow protect to time config
  • drivers: mcan Enlarge the range of CAN_EVENT_ERROR.
  • components: serial_nor: add subdirectory in cmakelists
  • middleware: cherryusb: update to v0.10.2
  • middleware: cherryusb: rename host and device isr
  • middleware: FreeRTOS: xPortIsInsideInterrupt() using CSR_MSCRATCH
  • middleware:hpm_sdmmc Enhanced all speed modes support for SD and eMMC.
  • middleware: usbx: device: support chain transfer
  • samples: cherryusb: host: rndis: integrate dhcp thread into ping thread for host rndis ping and iperf sample
  • samples: adc: temp: add isr for temp out of thresholds
  • samples: drivers: acmp: optimization for comparing input voltage
  • samples: lwip: add DHCP macro definition in CMakeLists.txt
  • samples: lwip_ptp: enable DHCP feature in PTP samples
  • samples: drivers: qeiv2: update API for adc-qeiv2 pin initialization
  • samples: bldc_foc: change adc buffer size from 40 words to 48 words
  • samples: remove explicitly c++ standard setting.
  • samples: driver: cam: set default cmake build type
  • samples: lwip: update to Class C static IP adress
  • samples: tinyuf2: remove unnecessary cache ops.
  • samples: lwip: lwip_tcpecho_freertos: optimization for API call in a thread-safe way
  • samples: lwip: lwip_ptp: v1: slave: update static ip
  • samples: lwip: optimize DHCP enable logic
  • samples: lwip: opts: adjust the allocation strategy of memory pool
  • samples: lwip: lwip_iperf: adjust MEM_SIZE for saving memory consumption
  • samples: lwip: lwip_tcpecho_multi_ports: update the second IP with C class
  • samples: enet: optimization for PHY selections
  • samples: dma: update uart rx circle transfer buffer size
  • samples: drivers: sdxc/emmc Correct doc for emmc sample.
  • cmake: sdk_link_libraries link libraries for supported tools.
  • cmake: add project name for hpm_sdk sub directory.
  • cmake: decouple CMAKE_BUILD_TYPE and linker script.
  • cmake: ses: remove -Ox from gcc option list.
  • cmake: set default c++ standard to c++11.
  • Update CONFIG_HAS_xxx to HPMSOC_HAS_xxx.
  • segger: enable all warnings.
  • segger: release: release optimization level use cmakelist config
  • scripts: ses: set intermediate dir in project file.
  • docs: remove quick start guide from top level readme
  • docs: change doc structure.

Added:

  • soc: HPM5361: add trgm filter shift length feature
  • soc & drivers: hpm5300: add DMAMUX_SOC_WRITEONLY and TRGM_SOC_HAS_DMAMUX_EN features
  • drivers: lcb: add lcb driver.
  • drivers: sdxc add more APIs for timing and power control.
  • drivers: mipi_csi: add mipi csi.
  • drivers: cam: add cam_stop_safely API
  • components: usb: device: add dtd chain transfer
  • components: panel: enable panel component.
  • components: camera: ov5640: add mipi interface.
  • middleware: rtthread-nano: add v3.1.5
  • middleware: rtthread-nano: add FPU support.
  • middleware: tinyusb: device: update to support chain transfer
  • middleware: cherryusb: device: update to support chain transfer
  • middleware: vglite: add 4.0.49.
  • middleware: cherryusb: add USB_OSAL_WAITING_FOREVER for sem and mq use
  • middleware: add hpm_mcl_v2
  • middleware: lwip: add ptpd v1 & v2
  • middleware: cmsis_os2: add source files.
  • samples: mcl: add step motor.
  • samples: lwip: lwip_ptp: v2: support IEEE1588 V2
  • samples: cherryusb: add audio_v2_mic_speaker_rtthread sample
  • samples: cherryusb: host: add hid and msc rtthread samples
  • samples: cherryusb: host: usbnet: add support ec20 module sample.
  • samples: cmsis_os2: add blinky sample.
  • samples: driver: mipi_csi: add mipi_csi.
  • samples: mcan Support MCAN4-7 loopback testing.
  • cmake: support custom output file name.

Fixed:

  • soc: fix cache maintenance at startup
  • soc: hpm53xx Correct exip API tree offset.
  • soc: toolchain: missing .fast.* in gnu ld linker script.
  • soc: fix tbss and tdata section not initialized.
  • soc: sysctl: sysctl_enable_group_resource() should be check LOC_BUSY
  • soc: hpm5300 Correct Cache size and Cacheline size.
  • boards: hpm6750evkmini Fix the issue that eMMC is still 3.3V even 1.8V is selected.
  • boards: hpm5301evklite correct jlink script device number.
  • components: camera: power_up is enable by default for ov5640/ov7725.
  • docs: samples: drivers: add numberic index.
  • drivers/soc: fix build warning
  • drivers: i2c: add slave device response judgment for master read/write APIs
  • drivers: opamp: fix opamp vssa connect error.
  • drivers: pllv2: fix pllctlv2_pll_is_stable() API
  • drivers: qeiv2: fix invalid argument check
  • drivers: dac: fix the upper limit value setting for DAC_OUTPUT
  • drivers: jpeg: fix pixel format index for out buffer.
  • drivers: uart: fix not support oversample 32 for rx idle detection on hpm5300
  • middleware:ftafs Fix SD card init crash.
  • middleware: mcl: fix path plan error.
  • middleware: hpm_sdmmc Fix the issue that IO initialization work unstable on HPM6300.
  • middleware: hpm_sdmmc Fix voltage switch setting issue for SD and eMMC.
  • middleware: hpm_sdmmc Fix the PWR and VSEL IO initiaization issue. refs:hpm-sdk-#863
  • samples: sei: fix nikon sample crc calc error.
  • samples: cherryusb: msc device: add pre-format fat12 file system in u disk
  • samples: adcx: replace const with a macro for ADC sample cycle
  • samples: tinyusb:fix the usb host pin init.
  • samples: motor_ctrl: bldc_littlevgl_foc: program crash.
  • samples: qeiv2: uvw: fix uninitialized pointer usage
  • samples: cherryusb: fix semaphore give in isr
  • samples: drivers: Fix the issue that can error example may block.
  • samples: uart_irq: fix unable to limit receive large than buffer size.
  • samples: drivers:sdxc:emmc remove infinite loop for emmc initialization.
  • samples: drivers: i2s: fix tx underflow during tx start
  • samples: lwip: lwip_tcpecho_multiple_ports: fix no echo data when receiving large amounts of data
  • samples: mcl: pwm duty set error.
  • samples: cherryusb: host: usbnet: fixed when performing a stress test with a large amount of iperf data, will send fai.
  • samples: cherryusb: audio_v2_mic_speaker_rtthread: fix mic no voice problem
  • samples: jpeg_decode: add delay after usb pins init for waiting power stable
  • samples: hfi: hpm6750evk2: fix the motor shake.
  • cmake: segger: remove workstation specific path info.
  • cmake/soc: fix heap/stack size setting for andes toolchain.
  • cmake: ses: correct device name for core1.

v1.3.0

28 Sep 03:55
Compare
Choose a tag to compare

[1.3.0] - 2023-09-28:

Main changes since 1.2.0

Tested Segger Embedded Studio Version: 7.32

Changed:

  • boards: hpm6200evk/hpm6300evk: delete unwanted clock_ahb div set
  • boards: hpm6750xxx: switch dcdc work mode to dcm mode
  • docs: sdk: boards: hpm6750evk2: add pps pin information
  • component: wm8960: support sysclk pre-divider
  • components: serial_nor: add serial nor flash.
  • openocd: probes: ft2232: remove trst and srst config.
  • ip: cam:remove 0x5c MAX_WN_CYCLE register in regs.h
  • driver: cam: remove invalid register
  • drivers: i2s: update API
  • drivers: adc: adc12/adc16: rename adc16_get_busywait to adc16_is_nonblocking_mode
  • drivers: adc: adc12/adc16: update adcx_init API
  • drivers: pllctrl: update pllctrl drivers
  • drivers: spi : add spi enable and disable datamerge
  • drivers: spi : add spi_set_address_len API
  • drivers: pdgo Add missing APIs
  • drivers: uart: update uart rx idle flag process and fifo control
  • soc: delete_unnecessary_ppor_reset_bit_field
  • soc: hpm_gpiom_soc_drv.h: delete gpiom_gpio_t soc name
  • soc: delete DMA_SOC_BUS_NUM Macro
  • soc: pcfg: update pcfg SCG_CTRL related drivers
  • soc: hpm6750:startup Enable LMM1 clock before access to LMM1
  • soc: gcc ld: add memory used size check
  • middleware: cherryusb: update to v0.10.1
  • middleware: guix: demo adapts to 800 * 480 resolution
  • middleware: guix: improve demo display performance
  • middleware: cherryusb: update for midi descriptor define
  • middleware: cherryusb: update for midi
  • samples: drivers: adc: adc12/adc16: speed optimization for oneshot reading
  • samples: drivers: adc: adc12/adc16: update API call used for nonblocking judgement
  • samples: drivers: adc: adc12/adc16: update API call related to blocking setting in oneshot mode
  • samples: drivers: adc: adc12/adc16: reduce the input parameters of init_trigger_target function
  • samples: drivers: adc: adc12/adc16: update init_oneshot_config
  • samples: drivers: adc: adc12/adc16: optimization for clearing interrupt status
  • samples: drivers: pwm: Add pwm clock jitter demo
  • samples: cherryusb: hid host: separate mouse and keyboard urb
  • samples: hrpwm: Add demo for updating hrpwm frequency
  • samples: drivers:mcan Add CAN error handling and refined logic.
  • samples: mbx: move dualcore mbx sample to multicore folder
  • samples: cherryusb: update for v0.10.1
  • samples: motor_ctrl: bldc smc: gcc toolcahin enable fpu.
  • samples: lwip: lwip_tcpecho_freertos: optimization in a thread-safety way
  • samples: qeo: update qeo abz frequency configuration
  • samples: gptmr: add sent_signal sample.
  • samples: lwip: lwip_ptp: remove the dependency on pps0 pinout
  • samples: dma_manager: update for use dma_mgr_setup_channel()
  • samples: drivers: gptmr: pwm_measure: support use dma
  • samples: lwip: lwip_httpsrv/lwip_https_server: rename project names for uniform naming
  • samples: multicore: lvgl_coremark: delete custom linker files and using andes toolchain
  • samples: flash_algo: update device size.
  • samples: cherryusb: host: hid: use ep_mps to fill urb

Added:

  • cmake: ses: support specify custom openocd board cfg file.
  • cmake: support specifying minimum sdk version in app.yaml.
  • boards: add hpm5300evk
  • components: eeprom_emulation: add hpm nor-flash support
  • components: eeprom_emulation: add eeprom emulation component
  • soc: add APIs for get or set sysctl resource status
  • drivers: common: add HPM_ALIGN_DOWN and HPM_ALIGN_UP define
  • drivers: adc: ad12/adc16: add adcx_set_blocking_read/adcx_set_nonblocking_read
  • drivers: add encoder position driver
  • drivers: lcdc: add enable/disable background in alpha blender.
  • drivers: usb: add api to set dp/dm pin pulldown resistance
  • drivers: spi: add spi_get_rx_fifo_valid_data_size and spi_get_tx_fifo_valid_data_size APIs
  • drivers: spi: add directIO function APIs
  • drivers: enet: add rx resume API
  • drivers: adc16: add resolution setting in adc16_get_default_config API
  • drivers:rtc Add rtc_get_timeval API.
  • drivers:mcan Add mcan_transmit_via_txfifo_nonblocking API.
  • drivers: usb: add usb_hcd_set_power_ctrl_polarity() API
  • drivers: plb: add plb drivers
  • drivers: linv2: add linv2 driver
  • drivers: sei: add sei driver
  • drivers: dmav2: add dmav2 driver
  • drivers: qeo: add qeo driver
  • drivers: qeiv2: add qeiv2 driver
  • drivers: mmc: add mmc driver
  • drivers: rdc: add rdc driver
  • drivers: add opamp driver
  • drivers: bgpr: add related APIs for bgpr
  • middleware: FreeRTOS: add xPortIsInsideInterrupt() API
  • middleware: threadx: add definition automatically when enable traceX
  • middleware: freeRTOS: add use gptmr to generate interrupt
  • middleware: hpm_mcl: add hfi
  • samples: drivers: adc: adc12/adc16: add wdog feature
  • samples: add opamp demo
  • samples: cherryusb: rndis: host: add iperf sample.
  • samples: cherryusb: rndis: host: add ping sample.
  • samples: drivers: adc: adc12/adc16: add hw trigger configuration in sequence mode
  • samples: eeprom_emulation: add eeprom emulation perf test sample
  • samples: eeprom_emulation: add base api demo
  • samples: tracex: add demo for traceX usage
  • samples: cherryusb: add audio_v1_mic_speaker_midi sample
  • samples: cherryusb: add midi device sample
  • samples: drivers: sei: add sei samples
  • samples: drivers: plb: add plb demo
  • samples: drivers: mmc: add mmc demo
  • samples: drivers: qeiv2: add qeiv2 demo
  • samples: drivers: qeo: add qeo demo
  • samples: drivers: dmav2: add dmav2 demo
  • samples: drivers: linv2: add linv2 demo
  • samples: drivers: rdc: add rdc demo
  • samples: drivers: pdgo Add PDGO samples
  • samples: drivers: ewdg Add EWDG sample
  • samples: lwip: add a lwip_tcpecho_multi_ports sample
  • samples: motor_ctrl: add hfi

Fixed:

  • cmake: fix segger default heap and stack size config
  • cmake: fix add_subdirectory_ifdef arg processing.
  • doc: boards: hpm6300evk: fix acmp pin info.
  • boards: hpm6750evkmini: fix board_init_rgb_pwm_pins() problem
  • boards: hpm6200evk: fix BOARD_G_GPIO_CTRL defined in wrong position
  • openocd: hpm6750-dual-core: fix expression warning.
  • component: wm8960: fix clock tolerance process
  • soc: toolchains: segger: block tls add with fixed order
  • soc: toolchain: gcc: fix Thread-Local Storage problem
  • soc: segger linker files: fix heap and ctors initialize
  • soc: fix interrupt complete operation
  • soc: pcfg: fix DCDC_PROT[OVERLOAD_LP] bit access
  • soc: ip: adc12: fix ADC12 threshold setting
  • soc: HPM6750: fix clock setting and frequency obatining error
  • soc: HPM6360: fix clock source definitions for ADC16
  • soc: HPM6280: fix clock source definitions for ADC16
  • soc: HPM6360: fix obtaining clock source error for DAC
  • soc: HPM6280: fix obtaining clock source for DAC
  • drivers: adc16: add bus mode enable control APIs
  • drivers: adc16: fix ahb setting
  • drivers: cam: clear the status of CAM should not affect other bits
  • drivers: trgmux: filter function can't work.
  • drivers: src: adc16: fix end count setting
  • drivers: adc/dac: fix interrupt status clearing
  • drivers: adc16: fix DMA access format
  • drivers: sdm: fix over sample rate and signal sync problem
  • drivers: pwm: fix pwm xcmp enable setting
  • drivers: pwm: correct external fault polarity setting.
  • drivers: pwm: add update hrpwm reload shadow api
  • drivers: spi: fix can't set change data_bits use spi_set_data_bits API
  • drivers: ptpc: fix ptpc_clear_irq_status API issue.
  • drivers: i2c: fix i2c_clear_status API issue.
  • drivers: gptmr: fix gptmr_clear_status API issue.
  • middleware: erpc: rpmsg_lite: fix platform_in_isr() error
  • middleware:hpm_sdmmc Fix the issue sdsc cards are not supported.
  • middleware: threadx: fix D extend asm code error
  • samples: usbx: add multi devices and hot plug support
  • samples: motor_ctrl: fix adc trig invalidate.
  • samples: lwip: fix TCP reception error when size over 2KB
  • samples: lwip: DHCP failure in lwip_tcpecho_freertos
  • samples: drivers: adc: adc12: fix the status flag judgement in isr process
  • samples: rgb_led: fix cmp shadow error
  • samples: gptmr: pwm_generate: fix inaccurate duty in high frequency
  • samples: lwip: low_level_input: fix the network storm issue
  • samples: timer_basic: fix inconsistent use of defines
  • samples: drivers: adc: adc16: fix the bit of interrupt status clearing in sequence mode
  • samples: power_mode_switch: trigger system lowpower for standby mode
  • samples: touch_panel: fix error data when 5 fingers touch screen at same time.
  • samples: jpeg: jpeg_decode: fixed lcd display is tore when decoder is running
  • samples: jpeg: jpeg_decode: malloc out of memory on gcc
  • samples: drivers:can Fix abnormal behavior on can error sample.
  • samples: segger_rtt: call board_init_clock.
  • samples: drivers: acmp: fix one toggle value but multi toggle pulses
  • samples: lwip_tcpecho_freerstos: fix code stuck with gcc toolchain
  • samples: jpeg: fix JPEG_USE_UDISK compile error
  • samples: bldc_foc: fix input value range.
  • samples: cherryusb: rndis: udp_echo: fix echo extra char
  • samples: usbx: fix global var placement
  • samples: power_mode_switch: set to preset_1 after exiting wait mode.
  • samples: pla: fix pla first pulse abnormal.
  • samples: plb: fix the first pulse is abnormal.

v1.2.0

03 Jul 02:40
Compare
Choose a tag to compare

[1.2.0] - 2023-06-30:

Main changes since 1.1.0

Tested Segger Embedded Studio Version: 7.22

Changed:

  • boards: hpm6750evk*: decrease core frequency from 816MHz to 648MHz
  • openocd: soc: hpm6280: simplify dual core release core1 approach.
  • cmake: segger: configure optimization level according to gcc level.
  • soc: dmamux: move it from ip to soc
  • soc: interrupt: adjust irq api. #659
  • soc: improve svd file
  • soc: hpm_soc_feature.h: remove ADC16_SOC_TEMP_CH_EN for some specified Socs
  • components: enet_phy: update the common enet phy header file
  • components: sgtl5000 and wm8960: update clock setting
  • drivers: uart: update uart driver
  • drivers: pdma: improve quality of scale
  • drivers: adc: adjust wait_dis type in adc16_config_t struct
  • drivers: enet: update rmii reference clock setting API for ENET
  • utils: hpm_swap: escape for andes toolchain.
  • middleware: hpm_sdmmc: add spi sdcard
  • middleware: motor_ctrl: change the file organization
  • middleware: motor_ctrl: remove slide control content from foc
  • middleware: lvgl: upgrade to v8.3.5 (with pdma)
  • middleware: lvgl: Add direct mode
  • middleware: cherryusb: update version to v0.8.0
  • samples: I2S_DMA and I2S Interrupt: update sample behavior
  • samples: cherryusb: hid host: separate mouse and keyboard urb
  • samples: cherryusb: increase max interface and endpoint number Configuration
  • samples: cherryusb: uac2: move setting sampling freq to isr
  • samples: cherryusb: audio: update descriptor for identification
  • samples: audio_codec: set codec voice to max and increase irq priority
  • samples: multicore: lvgl_coremark: delete custom linker files and using andes toolchain
  • samples: lvgl_audio_player: update CMakeLists.txt to using noncacheable framebuffer
  • samples: spi: clean the redundant code
  • samples: i2c: improve the processing of FIFO in ISR
  • samples: drivers: uart: update uart_rx_timeout demo
  • samples: drivers: gptmr: split sample into multiple function samples
  • samples: drivers: adc: optimization for all macro definitions in applications
  • samples: drivers: adc: update struct member names
  • samples: update clock divider setting for ADC-related examples
  • samples: cherryusb: move vid/pid etc definition to usb_config.h
  • samples: cherryusb: device: update vid to hpmicro 0x34B7
  • samples: cherryusb: change API update for v0.8
  • samples: cherryusb: device: audiov1: change to full speed mode
  • samples: tinyusb: uac2: update descriptor and sample
  • samples: lwip: disable mmc interrupt settings
  • samples: lwip: lwip_ptp: v1: sync precision improvement

Added:

  • cmake: toolchains: add isa spec 20191213 support.
  • cmake: ses: support set ses raw option in CMakeLists.txt
  • cmake: add option to specify board search path.
  • cmake: generate compile_commands.json file
  • soc: hpm_soc_feature: add a common macro for ADC12 and ADC16
  • drivers: cam: add new APIs
  • drivers: spi: add new APIs
  • drivers: i2c: add new APIs
  • drivers: I2S: add i2s_check_data_line_status API
  • drivers: dma: add dma_set_transfer_src_width_byte_size() API
  • drivers: gptmr: add output capture APIs
  • drivers: gptmr: add gptmr_channel_get_dma_request_event api
  • drivers: adc: add adc16_trigger_pmt_by_sw API
  • drivers: enet: add some APIs related to interrupt settings
  • drivers: enet: add a new API for transmisstion
  • drivers: usb: add macro CONFIG_USB_DEVICE_FS to set full speed mode
  • components: uart_lin: add uart lin component
  • components: add smbus
  • components: add sccb
  • middleware: lvgl: add macro HPM_LVGL_FRAMEBUFFER_NONCACHEABLE
  • middleware: add AzureRTOS (threadx/usbx/netx/guix)
  • middleware: hpm_mcl: sensorless over-zero
  • middleware: add smc
  • middleware: hpm_sdmmc Add eMMC support
  • middleware: hpm_math: add bit conversion function
  • middleware: add uC/OS-III
  • middleware: cherryusb: audio: add feedback descriptor
  • middleware: cherryusb: audio: add param to set endpoint bmAttributes
  • middleware: microros: add microros foxy sources
  • samples: drivers: spi: add spi_sdcard_fatfs sample
  • samples: drivers: spi: add sd sample
  • samples: add uart_lin
  • samples: motor_ctrl: sensorless: over-zero demo
  • samples: cherryusb: add rndis host dhcp samples
  • samples: drivers: sdxc :emmc Added eMMC sample
  • samples: drivers: adc12: update irq pattern for sequence usage
  • samples: drivers: pla: add pla tamagawa demo
  • samples: drivers: gptmr: add counter_sync sample
  • samples: drivers: gptmr: add timer_basic sample
  • samples: drivers: gptmr: add t_shape_accel_decel sample
  • samples: drivers: dma/gptmr: add trigger dma transfer using gptmr event sample
  • samples: drivers: uart add uart_rx_timeout sample
  • samples: i2c: add smbus samples
  • samples: lwip: lwip_tcpecho_freertos: add self-adaption
  • samples: cherryusb: hid host: move usbh_submit_urb() out of condition
  • samples: cherryusb: add composite freertos sample
  • samples: cherryusb: add rndis freertos sample
  • samples: cherryusb: add msc freertos sample
  • samples: cherryusb: add audio v2 mic speaker freertos sample
  • samples: cherryusb: add hid mouse freertos sample
  • samples: cherryusb: add hid keyboard freertos sample
  • samples: cherryusb: add cdc acm freertos sample
  • samples: cherryusb: add rndis tcp server sample
  • samples: cherryusb: add rndis device udp_echo sample
  • samples: cherryusb: add rndis device http_server sample
  • samples: cherryusb: device: add audio_v2_speaker_sync sample
  • samples: add several uC/OS-III samples
  • samples: smc: add smc demo
  • samples: microros: add subscriber, sevice and publisher
  • samples: uC/OS-III: mutex

Fixed:

  • cmake: ses: fix __SEGGER_RTL_vfprintf issue with nds tool in SES 7.20.
  • soc: hpm6280: Modify the number of PWM cmps.
  • soc: reset.c: __dso_handle needs to be declared for nds toolchain.
  • soc: fix max buffer length in sequence mode for ADC
  • soc: HPM6750: enet soc drv: fix set clock delay settings
  • soc:hpm6360:sdxc Correct clock divider settting issue
  • drivers: pla: missing Union Field
  • drivers: spi: fix the problem of CMD and ADDR configuration order
  • drivers: i2c: fix clock frequency error rate problem
  • drivers: i2c: clear CMPL bit in API to avoid blocking the trans
  • drivers: i2c: fix i2c slave device read and write fail
  • drivers: i2c: fix read data unexpected multi transition.
  • drivers: i2c: fix w1c clear status error
  • driver: usb: fix w1c clear flag error
  • drivers: gptmr: fix dma request enum definition
  • drivers: adc: fix logics for judging the validity of arguments
  • component: uart_lin: fix break signal problem
  • middleware: cherryusb: fix buffer size error
  • middleware: lvgl: fix fbbuffer option
  • samples: gptmr: fix pwm_measure sample compile waring
  • samples: jpeg: fix interchange format of exif support
  • samples: jpeg: fix jpeg decode
  • samples: drivers: spi: fix the problem of CMD and ADDR configuration order
  • samples: drivers: mcan: can_fd loopback test setting is incorrect
  • samples: cherryusb: http_server_freertos: fix printf content error
  • samples: cherryusb: audio: change endpoint attributes for support MACBOOK
  • samples: tinyusb: msc: increase block numbers for windows format
  • samples: lwip: lwip_httpsrv: fix reload or refresh error

v1.1.0

03 Jul 02:44
Compare
Choose a tag to compare

[1.1.0] - 2023-03-31:

Main changes since 1.0.0

Tested Segger Embedded Studio Version: 7.10

Changed:

  • docs: add new docs for rtd project.
  • soc: ip: enet: update the enet register file
  • soc: ip: adc16: update the adc16 header file
  • soc: hpm_romapi - Add APIs for configuring remapping, exip regions
  • drivers: enet: improve APIs related to PPS
  • drivers: adc: change adc bus blocking interface
  • drivers: adc: optimize getting oneshot result
  • drivers: src: update the default config for ADC12&ADC16
  • boards: rename board-level APIs related to enet
  • components: enet_phy: rtl8201: update the register file
  • middleware: hpm_math: update dsp version
  • middleware: erpc: update to v1.10.0
  • samples: uart: rename uart_dma_rx_idle to uart_software_rx_idle
  • samples: uart: add hardware rx idle detection sample
  • samples: multicore: erpc: core1 add sdk_compile_options(-O1)
  • samples: drivers: gptmr: update sample output.
  • samples: lwip: common: arch: ethernetif: update a calling function name
  • samples:drivers: adc: optimize oneshot handler

Added:

  • arch: add FPU related APIs
  • soc/board: add HPM6280 support
  • soc: HPM6750: acmp: add ACMP section
  • components: add mt9m114 support
  • drivers: add raw8 pixel format support
  • drivers: csr - Implement CSR driver
  • drivers: adc: adc16: support resolution setting
  • drivers/samples: add SDM/PLA/CRC/MCAN
  • drivers: I2C: add new API
  • drivers: adc: adc16: support resolution setting
  • drivers: enet: add enet control config for transmission
  • middleware: cherryusb: audio: update class driver and demo template
  • middleware: add mbedtls lib files with SDP acceleration
  • freeRTOS: add support for static allocation
  • samples: drivers: enet: add a pps demo
  • samples: cherryusb: add audio samples
  • samples: add the resolution parameter in all demos with ADC16
  • samples: add rfft demo
  • sampels: i2c: add interrupt b2b samples
  • samples: drivers: i2s: add an i2s_master demo
  • samples: drivers: i2s: add an i2s_slave demo
  • samples : rom_api : add sw_gm_api filter
  • samples: add the resolution parameter in all demos with ADC16

Fixed:

  • openocd: hpm6300evk: update sdram initialization.
  • drivers: trgmux: trigmux edge filter setting error
  • drivers: enet: fix register access error
  • drivers: adc16: fix the config error of ADC16_CONFIG1
  • drivers: i2c: fix i2c timing configuration
  • drivers: SPI: fix SPI status API
  • drivers: fix gptmr cmp value don't minus one
  • drivers: mcan: correct the mcan ext_id filter issue
  • drivers: I2C: fix issue in i2c_master_address_read API
  • drivers: Self_ACK cannot be set in CAN driver
  • drivers: rtc rtc_config_alarm always return error code
  • cmake: correct source code compilation
  • soc: toolchain: gcc: initialize heap for SES
  • soc: gcc linker files: add NOLOAD keyword to noncacheable.bss section
  • soc: HPM6360: gcc: ld: correct noncacheable region name.
  • drivers: qei: Fix speed display always zero
  • middleware: freertos: disable global irq before vTaskStartScheduler
  • freeRTOS: fix trap when enable float feature
  • freeRTOS: fix tick lost
  • freeRTOS: fix segger project build warning
  • samples: drivers: i2s: fix CFGR config
  • samples: drivers: fix acmp toggle error
  • samples: lwip: fix the DHCP issue
  • samples: uart: fix irq_id judgment
  • samples: fix the order of uart pin configuration and clock configuration
  • samples: update spi dma sample
  • samples: drivers: sysctl: correct reset enable approach.
  • samples: fix dma_general_transfer sample memory out of bounds
  • samples: drivers: wdog: Fix logic issue on finding the nearest interrupt interval
  • sample: audio_codec: decoder_wav: add '\0' to fatfs path

v1.0.0

03 Jul 02:45
Compare
Choose a tag to compare

[1.00.0] - 2022-12-31:

Main changes since 0.14.0

Tested Segger Embedded Studio Version: 7.10

Changed:

  • boards: add version info in banner.
  • board: lcdc: move panel para to board
  • components: spi component to support to transfer different width of data in dma handshake mode
  • drivers: rename dram to femc
  • middleware: cherryusb update to v0.7.0
  • middleware: erpc: update for support rtos
  • middleware: hpm_mcl: update api naming
  • samples: erpc: rename erpc_matrix_multiply_rpmsg to erpc_matrix_multiply_rpmsg_bm
  • samples: erpc: reorganize erpc_matrix_multiply_rpmsg samples
  • samples: erpc: move samples folder to erpc_matrix_multiply_rpmsg
  • samples: update i2c/spi dma channel and dmamux channel definition
  • ses: project template: use demo.* as output file naming.
  • soc: HPM6750: toolchains: update linker files
  • soc: HPM6360: toolchains: update linker files

Added:

  • arch: riscv: add read_clear_csr() API
  • component: add wm8960 support
  • component: add usb device iso transfer support
  • drivers: hpm_common: include hpm_sdk_version.h.
  • drivers: common: add NOP and WFI.
  • drivers: uart: add api to recv/send byte directly.
  • soc: HPM6750 linker files: rename rpmsg_sh_mem to sh_mem
  • cmake: add sdk version header file generation.
  • middleware: tinyusb: add audio class
  • middleware: hpm_math: add NN library
  • samples: erpc: add erpc_two_way_rpc_rpmsg_rtos sample
  • samples: erpc: add erpc_matrix_multiply_rpmsg_rtos sample
  • samples: add power mode switch demo. #282
  • samples: drivers: adc: add a temperature measurement demo
  • samples: drviers: femc: add sram sample
  • samples: lwip demo for FreeRTOS
  • samples: lwip demo of interrupt usage
  • samples: tinyusb: add uac2 demo
  • samples: tflm: add face detection demo
  • samples: tflm: add MLPerf Tiny benchmark demo
  • samples: lwip: common: feature: add a LPI interrupt process

Fixed:

  • drivers:interrupt: Fix FPU context crashing in nested irq case
  • drivers: src: adc: fix adc result in period mode
  • segger: update app directory structure in SES.
  • soc: disable irq during cache maintenance
  • middleware: lvgl: fps calculation to No.
  • samples: get off level based on board api.
  • samples: multicore: hello: core1 rgb led does not change correctly.