v1.7.0

[1.7.0] - 2024-09-30:

Main changes since 1.6.0
Tested Segger Embedded Studio Version: 8.16a
Tested Zcc toolchain 3.2.4

Changed:

• soc: HPM6E00: HPM6E80: add tsw section
• soc: add hpm_otp_table.h
• soc: enet: add a macro for DMA bus width
• soc: system.c: set bpor.por_confing retention bit to avoid bgpr data loss
• soc: pcfg: add pcfg_wakeup_src_t enum and pcfg_update_periph_clock_mode API
• soc: hpm5300: exclude fgpio region from dlm
• soc: add CONFIG_ENABLE_BPOR_RETENTION macro to control bpor retention
• soc: linker: icf: update cherryusb_usbh_class_info section placement
• soc: HPM6300/HPM6700: delete pcfg_dcdc_set_current_hys_range() API
• ip: i2s: add and use clk_i2s_src_audn instead of clk_i2s_src_aud0/1/2/3
• boards: remove hpm6750evk support
• boards: hpm6e00evk: update femc pinmux
• boards: pinmux: set max frequency slew rate for SPI GPIO
• boards: hpm5301evklite: Change cap1 and comp1 pins of gptmr0
• boards: hpm5301evklite: change i2c2 to i2c3 for BOARD_APP_I2C
• boards: add board_init_gptmr_channel_pin API for all board
• boards: hpm6e00evk: update core1 debugger console readme
• boards: all: add board_init_acmp_pins API
• boards: hpm6800evk: adc16: update clock bus name for clock initialization
• boards: adc16: rename api parameter clk_src_ahb to clk_src_bus
• boards: add BOARD_APP_ADC16_CLK_BUS definition
• boards: hpm6e00evk: update board readme
• boards: hpm6e00evk: bump up DCDC voltage to 1250mv
• boards: add enet pps input feature and pinmux setting API
• boards: add missing board feature and pin descriptions for enet pps output pin
• boards: xxxx.yaml: rename board feature name related to enet pps pin
• boards: add BOARD_MASTER_I2S and BOARD_SLAVE_I2S
• boards: add board mic and speaker i2s definition
• boards: doc: pwm: add pwm pin descriptions.
• boards: hpm6800evk reduce ddr io leakage.
• boards: hpm6800evk: pps: adjust pinmux settings
• drivers: tsw: optimize the logic of sending and receiving APIs
• drivers: tsw: add APIs for speed, interface, and clock delay settings
• drivers: tsw: split tsw_ep_enable_mac_ctrl API to two APIs for enableing and disabling
• drivers: usb: update usb phy init for suspend
• drivers: qeiv2: update comments
• drivers: i2c: auto ack needs to be enabled after the transmission is completed for i2c_master_transfer API
• drivers: adc16: split adc16_set_pmt_queue_enable() into enable and disable API
• drivers: gptmr: add opmode cntmode monitor configuration member for gptmr_channel_config API
• drivers: spi: add the judgment that the frequency ratio cannot be greater than 510 for spi_master_timing_init API
• drivers: enet: add retry logic in DMA initialization
• drivers: spi: Add slave mode judgment for spi_control_init API
• drivers: spi: add spi busy state judement for transfer APIs
• drivers: uart: add disable rx timeout trigger dma function
• drivers: i2s: add buff data align with frame feature
• drivers: acmp: add acmp_channel_config_cap_selection
• drivers: acmp: update acmp_channel_config_dac API
• drivers: usb: update usb phy init and deinit
• drivers: enet: add auxiliary snapshot APIs and struct definitions
• drivers: usb: update usb_force_port_resume() annd add usb_hcd_disable_ase_pse() APIs
• drivers: tsw: update the prefix of apis starting with tsn to tsw
• drivers: qeiv2: update qeiv2_config_adcx_adcy_param()
• drivers: usb: update usb_hcd_disable_ase_pse() & usb_hcd_enable_ase_pse()
• components: enet_phy: rtl8211: optimize logic for initialization config
• components: ppi: add assert check for cs_index and cmd_start_index
• components: ppi: update AD-MUX mode config to decrease address latch
• components: smbus: i2c_master_write replaces i2c_master_transfer for all smbus write APIs
• components: serial_nor: Added configuration return judgment for transfer API
• components: serial_nor: judge DMA sending completion for hpm_spi_transfer_via_dma API
• components: spi: add spi busy state judgment for hpm_spi_transfer_init API
• components: i2s_over_spi: add hpm_i2s_master_over_spi_tx_buffer_nonblocking API
• components: i2s_over_spi: optimized hpm_i2s_master_over_spi_tx_stop API
• components: i2s_over_spi: add hpm_i2s_master_over_spi_tx_is_busy API
• middleware: hpm_math: support zcc new version
• middleware: cherryusb: update to v1.4.0
• middleware: lwip: CMakeLists.txt: add cmake flag for apps
• middleware: cherryusb: don't clean csc bit when init
• middleware: cherryusb: msc host: support multi msc device
• middleware: fatfs: cherryusb: support two msc device
• middleware: reduce netx mem usage
• middleware: cherryusb: host: update usb_hc_deinit()
• middleware: usbx: host: delete mode setting in usb_host_mode_init()
• middleware: hpm_sdmmc: sdcard: added retransmission to improve SPI SD card compatibility
• middleware: tinyengine: rename old function
• samples: audio_codec: change default codec setting in CMakeLists.txt
• samples: adc16 & motor_ctrl: update adc16 preemption queue enable control APIs
• samples: ppi: parallel_adc: update function name
• samples: ppi: async_sram: update to support AD Mux Mode
• samples: lwip & modbus: add judgement for the return value of enet controller initialization
• samples: lwip: lwip_iperf: exclude flahsh_uf2 & flash_uf2_release targets
• samples: lwip: add conditional compilation for RMII port
• samples: cherryusb: msc host: adapter to fatfs update
• samples: drivers: acmp: replace init_acmp_pins API with board_init_acmp_pins API
• samples: ecat: read mailbox ram buff by ram alias address
• samples: ecat: set PHY offset
• samples: ecat_phy: disable PHY addr 00 broadcast response
• samples: drivers: adc16: reference APP_ADC16_CLOCK_BUS instead of clk_adc_src_ahb0
• samples: ecat_io: update flash_eeprom data address
• samples: ecat: update SSC config xml and ESI xml
• samples: lwip: ports: rtthread-nano: single&multiple: add sys_arch_protech()/sys_arch_unprotect()
• samples: power_mode_switch: move sysctl_enable_cpu0_wakeup_source_with_irq() to stop mode settings
• samples: power_mode_switch: keep puart clock and wakeup enable visible
• samples: acmp: add a macro TEST_ACMP_DAC_MAX_VALUE for better compatibility
• samples: drivers: enet: pps: app.yaml: rename dependency
• samples: ppi: parallel_adc: use macro BOARD_PPI_ADC_CS_INDEX
• samples: i2s: use BOARD_MASTER_I2S and BOARD_SLAVE_I2S
• samples: audio_codec: use board speaker macros
• samples: cherryusb: audio: use board mic and speaker macros
• samples: lwip & cherryusb/host/usbnet: use the external struct timeval definition from compile system
• samples: esc: update esc read to 32bit access
• samples: ecat_foe: update log and README
• samples: ecat_foe: foe flash read cache maintenance
• samples: ppi: use macros to select pins
• samples: drivers: gptmr: cntmode: volatile to key parameter variables to prevent them from being optimized
• samples: spi_sdcard: Added delay function registration
• samples: cherryusb: mouse_wakeup: update printf log
• samples: cherryusb: midi: update readme
• samples: i2s: change HDMA to XDMA
• samples: tflm: optimized speed.
• samples: tflm: add zcc compile options.
• samples: spi_component: full_duplex: Add known issues in the master readme
• samples: spi_components: half_duplex: reduce SPI SCLK frequency to adapt to different slave boards
• samples: spi_components: full_duplex: reduce SPI SCLK frequency to adapt to different slave boards

Fixed:

• soc: HPM6800: HPM6880: fix the clock bus name for wdg
• soc: SPI_SOC_TRANSFER_COUNT_MAX Definition error for HPM6E00
• soc: preserve kept symbols while -flto is enabled
• soc: hpm6880: fix clk bus name for adc from ahb0 to axis0
• soc: HPM6300: fix get get_frequency_for_i2s_or_adc() problem
• soc: HPM6700: fix clock_set_i2s_source() check condition
• soc: romapi: Fix unexpected data fetch error during flash init/write.
• soc: linker: gcc: fix fast_ram postion
• boards: hpm5301evklite: add a missing macro BOARD_APP_ADC16_CLK_BUS
• boards: i2c init: clock_add_to_group() should be before board_i2c_bus_clear()
• boards: hpm6800evk pinmux PRS set wrong value
• boards: hpm6750evkmini: fixed the iomux errata causes the slave to not work issue
• boards: hpm6750evk2: fixed the iomux errata causes the slave to not work issue
• boards: hpm6750evkmini: add the missing implement of enabling enet irq
• boards: hpm6750evkmini: fix touch reset timing.
• drivers: i2c: correct API name
• drivers: gptmr: fix cmp value can't set 0xFFFFFFFF problem
• drivers: pwmv2: fix counter burst set error.
• drivers: enet: fix return value of enet_dma_init()
• drivers: usb: fix usb_dcd_remote_wakeup() api
• drivers: enet: fix enet max frame size
• drivers: spi: Fixed mode variable assignment error for spi_slave_get_default_format_config API
• drivers: i2s: fix fill dummy data in slave mode
• drivers: adc16: fix ADC16 conversion results in single-ended mode
• drivers: enet: fix that TSIS interrupt is disabled by default
• drivers: femc: fix cmd_data_width comment error
• drivers: spi: fixed offset digit error problem for spi_get_rx_fifo_valid_data_size and spi_get_tx_fifo_valid_data_size APIs
• drivers: spi: fixed possible packet loss during reception for spi_read_data API
• drivers: usb: fix phy init for host
• drivers: touch: gtxx: fix reset timing
• drivers: mipi dsi: fix bandwidth low
• drivers: mcan: fix wrong offset in can_rx_message_t.
• drivers: adc12: fix using a wrong calibration value
• components: ppi: fix config variable init value
• components: serial_nor: Fixed the nonblock APIs naming error
• components: serial_nor: spi: fixed formating issue for write API
• components: eeprom_emulation, add "fence.i" after nor_flash init
• components: spi: fixed the waring of no return value for hpm_spi_transfer_init API
• middleware: fix Nan calculation error.
• middleware: lwip: apps: lwiperf: fix the type of clk_id from int to clockid_t
• middleware: fix tickless mode cannot work
• middleware: eclipse_threadx: netxduo: fix confilicting types for 'enet_mask_interrupt_event'
• middleware: tinyengine: zcc compile error.
• middleware: cherryusb: fix msc class miss return
• middleware: motor_monitor: fix nds toolchain error
• middleware: hpm_mcl: pwm output exception.
• samples: sdm: correct gptmr trigger time
• samples: gptmr: cmp0 and cmp1 should be setting together
• samples: i2s_emulation: fixed playback is not actually stopped issue
• samples: pwmv2: fix pwm period error.
• samples: drivers: dac: fix output stop after restart in buffer mode
• samples: fatfs: fix driver_num_buf don't have EOF
• samples: dac: buffer mode: fix DAC output of negative narrow pulse nearly to zero at the top of sinewave
• samples: lwip: fix enet receive buffer size setting
• samples: lwip: fix some memroy-related issues when using socket/netcon API
• samples: cherryusb: audio: fix mute problem when audio open
• samples: power_mode_switch: fix hpm62xx/63xx/67xx into shutdown mode can't be woke up
• samples: i2s: fix pdm record data buff size according board
• samples: lwip_ptp: v1 & v2: fix compiling error with gnu gcc toochain in v13.0
• samples: i2s_emulation: fixed build error for nds gcc
• samples: drivers: spi: interrupt: Abnormal working for IAR release build
• samples: lwip: lwip_ptp_v2: fix function error with flash_sdram_xip_release
• samples: drivers: spi: dma: master: fixed can not work sometimes with release build issue
• samples: i2s_emulation: fixed can not stop when playing issue
• samples: drivers: gptmr: opmode: fixed can not work with release build type
• samples: dsp: Calculation error in dsp demo.
• samples: lwip: lwip_ptp_v2: fix function error with flash_sdram_xip_release
• samples: drivers: uart: uart_hardware_rx_idle: fiexd can not work with zcc release build type
• samples: bldc offline detection: fix release run error.
• samples: mono: fix value get logic on zcc.
• samples: fix sample slave tamagawa's trx error handling method
• samples: ecat: fix build ZCC error
• samples: lower power: hpm6300 and hpm6700 can't use pcfg_dcdc_set_current_hys_range() API
• cmake: ide: correct glob source adding
• cmake: zcc: correct arch setting to enable dsp
• scripts: add errors=ignore and encode=utf8 parameters to avoid python unicode build error.
• samples: motor_ctrl: bldc_xxx & step_motor_foc: add missing diff_sel passed into adc12_init()
• samples: ethercat: ecat_cia402: motor: bldc_foc: add missing diff_sel passed into adc12_init()
• samples: drivers: adc: adc12: add missing diff_sel passed into adc12_int()
• doc: fix threadx doc title

Added:

• soc: HPM6300: add pps1_en
• drivers: add hrpwm recovery method.
• drivers: trgmux: add hrpwm calibration driver.
• drivers: sei: add sei_set_dma_req_enable() API
• drivers: ppi: add and use ppi_ns2cycle() API
• drivers: i2c: add I2C_WRITE_CHECK_ACK flag for i2c_master_transfer API
• drivers: i2c: add i2c_master_seq_transmit API
• drivers: plb: add new plb interface
• drivers: tsw: add tas, cbs and pps APIs
• drivers: tsw: add tx-timestamp-fifo APIs
• components: tsw_phy add RTL8211 and JL1111 drivers
• components: add pmbus
• components: ppi: add README.md docs
• components: add plb abz encoder.
• middleware: add hpmicro monitor.
• middleware: motor_ctrl: add motor parameter detection.
• middleware: add tsn
• samples: tsn: add lwip_tcpecho
• samples: bldc_foc: add motor monitor demo.
• samples: motor_ctrl: add bldc parameter detection demo.
• samples: drivers: pwmv2: add hrpwm calibration demo.
• samples: cherryusb: add mouse remote wakeup sample
• samples: gptmr: add opmode/monitor/cntmode sample
• samples: add pmbus samples
• samples: cherryusb: dual_host: support two msc device
• samples: ecat: add ecat_foe samples
• samples: ecat: add ecat_cia402 samples
• samples: ecat: add ecat_foe driver
• samples: ecat: update hpm_ecat_hw driver
• samples: drivers: enet: add pps_capture sample
• samples: add plb encoder demo.
• samples: tsn: add tsn_time_aware_scheduling
• samples: tsn: add tsn_ptp_freertos(master&slave)
• samples: tsn: add tsn_credit_based_shaper
• samples：ecat_cia402: add virtual motor support