-
Notifications
You must be signed in to change notification settings - Fork 35
/
README.txt
150 lines (109 loc) · 6.39 KB
/
README.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
Remserial
---------
The remserial program acts as a communications bridge between a TCP/IP
network port and a Linux device such as a serial port. Any character-oriented
Linux /dev device will work.
The program can also use pseudo-ttys as the device. A pseudo-tty is like
a serial port in that it has a /dev entry that can be opened by a program
that expects a serial port device, except that instead of belonging to
a physical serial device, the data can be intercepted by another program.
The remserial program uses this to connect a network port to the
"master" (programming) side of the pseudo-tty allowing the device driver
(slave) side to be used by some program expecting a serial port. See example
3 below for details.
The program can operate as a server accepting network connections from
other machines, or as a client, connecting to remote machine that
is running the remserial program or some other program that accepts
a raw network connection. The network connection passes data as-is,
there is no control protocol over the network socket.
Multiple copies of the program can run on the same computer at the same
time assuming each is using a different network port and device.
Some examples:
1) Give access to a RS232 device over a network.
The computer with the serial port connected to the device (such as a
data aquisition device) runs the remserial program:
remserial -d -p 23000 -s "9600 raw" /dev/ttyS0 &
This starts the program in daemon mode so that it runs in the background,
it waits for connections on port 23000 and sets up the serial port
/dev/ttyS0 at 9600 baud. Network connections to port 23000 from any
machine can then read and write to the device attached to the serial port.
This can be started from /etc/rc.local or as an entry in /etc/inittab
or set up as a system service with a file in /etc/rc.init/.
2) Connect an RS232 device to a specified server.
The computer with the serial port connected to the device (such as a
data aquisition device) runs the remserial program:
remserial -d -r server-name -p 23000 -s "9600 raw" /dev/ttyS0 &
This would be used with case number 1 above creating an end-to-end serial
port connection. What goes in the serial port on one machine would come
out the serial port of the other machine. The ports could be running at
different baud rates or other serial port settings.
3) Connect a Linux program that needs a serial port to a remote serial port.
Some programs are written to communicate directly with a serial port such
as some data aquisition programs. The remserial program can use
pseudo-ttys to fool the program into thinking that it is talking to a
real serial port on the local machine:
remserial -d -r server-name -p 23000 -l /dev/remserial1 /dev/ptmx &
This creates a file called /dev/remserial1 which can be used by the
data aquisition application as its serial port. Any data sent or received
is passed to the remote server-name on port 23000 where a computer configured
in case number 1 above passes it to a real serial port.
The remserial program uses the special pseudo-tty master device /dev/ptmx
(see man ptmx) which creates a slave device that looks like a normal
serial port named /dev/pts/something. Unfortunately, the actual device
name created isn't consistent, so the remserial program creates a symbol
link from the device name specified with the -l option to the /dev/pts/
name that was created allowing the other application to be configured
with a consistent device name.
4) Server farm console control.
Assuming multiple Linux servers (such as web servers) are set up to have a
serial port as their console instead of a monitor/keyboard, their serial
ports could be connected to a control server using a multi-port serial board.
On the control server, a copy of remserial is run for each server:
remserial -d -p 23000 -s "115200 raw" /dev/ttyS0 &
remserial -d -p 23001 -s "115200 raw" /dev/ttyS1 &
remserial -d -p 23002 -s "115200 raw" /dev/ttyS2 &
remserial -d -p 23003 -s "115200 raw" /dev/ttyS3 &
etc.
From any computer on the local network, use a telnet program to connect
to the control server on the appropriate port:
telnet control-server-name 23002
This would connect through the associated serial port to the desired server's
console. This example would then give the user console access to the 3rd
server.
Careful scripting such as using the Linux "expect" program could allow
batches of commands to be run on each server.
Other Linux program useful with remserial
-----------------------------------------
- nc - The netcat program is similar to remserial except that it creates
connections between network ports and command line standard input and
output.
For example, with case number 1 above, the following command run on
another computer will send the contents of the named file out the
serial port used by the remserial program:
nc server-name 23000 <file-name
Similarily, the following command will store incoming serial data in a file
until the program is manually interrupted:
nc server-name 23000 >file-name
- telnet - The telnet program is normally used to log into a remote computer,
but when used with network ports other than number 23, it operates in a
raw data mode.
For example, with case number 1 above, the following command will allow
the user of the telnet program to see incoming serial port data and
type data on the keyboard to send to the serial port:
telnet server-name 23000
This is ideal for controlling the device connected to the serial port
if it has some sort of command line interface usable over the serial port.
remserial Usage:
---------------
remserial [-r machinename] [-p netport] [-s "stty params"] device
-r machinename The remote machine name to connect to. If not
specified, then this is the server side.
-p netport Specifiy IP port# (default 23000)
-s "stty params" If serial port, specify stty parameters, see man stty
-d Run as daemon programs
-x debuglevel Set debug level, 0 is default, 1,2 give more info
-l linkname If the device is /dev/ptmx, creates a symbolic link
to the corresponding slave pseudo-tty so that another
application has a static device name to use.
-m max-connections Maximum number of simultaneous client connections to allow
device Character oriented device node such as /dev/ttyS0.