Copyright 2007 Vincent van Dam
Home pages:
This is an adjusted MSX diskrom that loads sectors from rom instead of a disk. It can be used to convert .dsk images to .rom images. The converted .rom images will act as a read only drive. If another diskinterface is present, it will be omitted (thus not usuable).
Converting .dsk images can be done by either using the dsk2rom tool, or by concatenating the custom a .dsk file to the custom diskrom. The dsk2rom tool doesn't run on MSX, but adds a few interesting new features (like compression and switching of mapper type).
To convert .dsk images to .rom images without the dsk2rom tool; use the following commands:
- MSXDOS 2:
concat /b dsk2rom.rom+<dskfile> <romfile> - Windows/MS-DOS:
copy /b dsk2rom.rom+<dskfile> <romfile> - Unix:
cat dsk2rom.rom <dskfile> > <romfile>
The mapper that is used is for the converted rom without using the dsk2rom tool itself is 'KonamiSCC'.
If the dsk2rom tool is used for conversion, a few more options will become available. The dsk2rom tool is a command-line tool with a few options. The available options will be displayed when the tool is started with no arguments at all.
Examples converting .dsk image to .rom images using the dsk2rom tool;
dsk2rom -f6c 2 alesteg.dsk alesteg.romdsk2rom -sfc 2 feedback.dsk feedback.rom
The most interesting option is compression (-c), it should be followed by a number which defines which compression should be used. Compression level 0 means no compression at all, and has the highest performance in loading. The resulting rom image will be the same as creating one without the tool. Level 1 compression will only index sectors, which means all redundant sectors will be removed. Level 2 compression adds the 'pletter' compression scheme upon the sectors and will result in smaller rom files, but also in a slightly lower performance when loading the rom image.
By default the resulting .rom images will use the Konami SCC mapper, this can be changed to the ASCII8 mapper. Some (bigger) flash cartridges use the ASCII8 mapper, the dsk2rom tool can patch the kernel to use the ASCII8 mapper addresses instead by adding the -a option when converting. Note that it is not wise to let the flash software patch the .rom image for you, because most of the .rom image is actually a data part, the flash software could wrongly patch this data, corrupting the image.
Especially the SCC mapper can conflict with aggressive memory search methods. To shield against this you can use the -s option (safe mode), which will always result in a rom which will either be 512K or 1024K. The rom will then be less vulnerable against memory searches.
Other options include; -5 and -6 to either switch to 50hz/pal or 60hz/ntsc during boot of the rom. The ability to force the msx1 palette using -p, as well as to allow booting of other diskroms to with -d.
The other options available are -v for verbose information while creating the rom, and the -f option to create rom images in standard sizes (2^sizes).
This should be enough info to start converting .dsk images to .rom images. Good luck!
A -r option has been added to allow to create back a dsk image from a rom created using dsk2rom tool. All compression modes are supported and roms with safe mode are also supported.
example of creating a .dsk image from a .rom created with dsk2rom tool
dsk2rom -r alesteg.rom alesteg.dsk
DSK2ROM by Vincent van Dam. The kernel was based on the disassembled diskroms by Arjen Zeilemaker. The pletter compression used in the kernel and tooling is made by Sjoerd Mastijn, which was based on Bitbuster by Arjan Bakker. A thank you to Arturo Ragozini for suggesting to use pletter compression. A lot of thanks go to Ramones for his testing and diskrom kernel hacking, and not to forget his GETDPB implementation included in the kernel. Another thank you to Sylver Bruneau for contributing the decoding of dsk2rom roms backs to dsks. Thanks to Sylvain Glaize who wrote the c implementation of pletter decompression allowing to revert pletter compressed roms : https://gitea.zaclys.com/Mokona/Unpletter .
- added safe mode to support dsk images with aggressive memory searching
- added setting 50/60hz during boot
- added setting msx1 palette during boot
- added non-exclusive boot mode
- added dsk2rom tooling for pc
- compression support
- improved mapper support (default scc, switchable via the dsk2rom tooling)
- removed last part of interrupt handler
- disabled h.hstke
- improved getdpb
- fixed loading into page 1
- removed custom interrupt handler
- another hack added to make sure it's always the only diskrom
- fixed loading into page 1
- support for ascii8 mapper
- first public release