ARTIK 053

The ARTIK 053 is a SOC for Wi-Fi™ IoT solutions. The ARTIK 053 has a Wi-Fi subsystem, security subsystem, and application subsystem.

Information

The Samsung ARTIK™ 053 Module is a highly integrated module for secure Internet of Things (IoT) devices that require Wi-Fi®. It is based on an ARM® Cortex® R4 core with on-chip memories, a complete 2.4GHz Wi-Fi® Phy, MAC layer processing, a large complement of standard digital buses, a PUF-based security system and power management. The module is packaged with additional external Flash memory, a hardware Secure Element and a single integrated 2.4GHz structural antenna. Aimed especially at power-sensitive devices needing Wi-Fi®, the ARTIK 053 Module provides excellent performance in a variety of environments, with a feature set tailored specifically for IoT end nodes.

ARTIK053 Starter Kit PinOut

CON710 CON711 CON708 CON709

                 XGPIO13(gpio42) <- SW702 | SW703 -> XGPIO15(gpio44)
                XGPIO16(gpio45) <- LED703 | LED702 -> XGPIO20(gpio49)
                                             [CON708]
                           |           |     * -> XI2C0_SCL
                           |           |     * -> XI2C0_SDA
                           |           |     * -> AREF
              [CON710]     |           |     * -> GND
               NC <- *     |           |    13 -> XSPI1_CLK
               NC <- *     |           |    12 -> XSPI1_MISO
            RESET <- *     |           |    11 -> XSPI1_MOSI
             3.3V <- *     | ARTIK053  |    10 -> XSPI1_CSN
               NC <- *     |           |     9 -> XPWMTOUT_4
              GND <- *     |           |     8 -> XGPIO21(gpio50)
              GND <- *     |           |     [CON709]
              Vin <- *     |           |     7 -> XGPIO19(gpio48)
              [CON711]     |           |     6 -> XPWMTOUT_2
            XADC0 <- A0    +-----------+     5 -> XPWMTOUT_1
            XADC1 <- A1                      4 -> XGPIO18(gpio47)
            XADC2 <- A2                      3 -> XPWMTOUT_0
            XADC3 <- A3                      2 -> XGPIO17(gpio46)
            XADC4 <- A4                      1 -> XUART0_TX
            XADC5 <- A5                      0 -> XUART0_RX

                   [CON703]
                   2 4 6 8 10 12 14 16 18 20 22 24
                   1 3 5 7  9 11 13 15 17 19 21 23
                   [CON704]
                   2 4 6 8 10 12 14 16 18 20 22 24
                   1 3 5 7  9 11 13 15 17 19 21 23

CON703

                 XPWMTOUT_1 <-  1 |  2 -> VCC_EXT3P3
                 XPWMTOUT_2 <-  3 |  4 -> XADC6
                 XPWMTOUT_3 <-  5 |  6 -> XADC7
                 XPWMTOUT_0 <-  7 |  8 -> XI2C1_SCL
                 XUART1_RXD <-  9 | 10 -> XI2C1_SDA
                 XUART1_TXD <- 11 | 12 -> GND
            XGPIO26(gpio55) <- 13 | 14 -> VCC_EXT3P3
            XGPIO25(gpio54) <- 15 | 16 -> XSPI0_CLK
            XGPIO24(gpio53) <- 17 | 18 -> XSPI0_CSN
            XGPIO23(gpio52) <- 19 | 20 -> XSPI0_MISO
            XGPIO22(gpio51) <- 21 | 22 -> XSPI0_MOSI
             XEINT0(gpio57) <- 23 | 24 -> GND

CON704

                 XPWMTOUT_4 <-  1 |  2 -> VCC_EXT3P3
                 XPWMTOUT_5 <-  3 |  4 -> XUART2_RXD
             XEINT2(gpio59) <-  5 |  6 -> XUART2_TXD
             XEINT1(gpio58) <-  7 |  8 -> XUART3_RXD
            XGPIO12(gpio41) <-  9 | 10 -> XUART3_TXD
            XGPIO10(gpio39) <- 11 | 12 -> GND
             XGPIO9(gpio38) <- 13 | 14 -> VCC_EXT3P3
            XGPIO11(gpio40) <- 15 | 16 -> XGPIO4(gpio33)/XSPI2_CLK
             XGPIO8(gpio37) <- 17 | 18 -> XGPIO5(gpio34)/XSPI2_CSN
             XGPIO2(gpio31) <- 19 | 20 -> XGPIO6(gpio35)/XSPI2_MISO
             XGPIO1(gpio30) <- 21 | 22 -> XGPIO7(gpio36)/XSPI2_MOSI
             XGPIO3(gpio32) <- 23 | 24 -> GND

MemoryMap

8MB is allocated to the SPI Flash area. 1280 KB is prepared for operation in SRAM. Here is the physical memory address, see [here].

Environment Set-up

This section covers board-specific environment set-up.
Please set TizenRT common environment, quick start, first before doing below.

Add USB device Rules

This is an optional environment.
But as ARTIK is connected through USB, some operation like programming of binary can't be worked without this configuration.

By dbuild.sh script

The dbuild.sh script with the menu option supports the u. USBrule option to add it.

Select the d. Download option after building TizenRT

======================================================
  "Select build Option"
======================================================
  "1. Build with Current Configurations"
  "2. Re-configure"
  "3. Menuconfig"
  "4. Build Clean"
  "5. Build Dist-Clean"
  "6. Build SmartFS Image"
  "d. Download"
  "x. Exit"
======================================================
d

Select the u. USBrule option

==================================================
  "Select download option"
==================================================
  "1. ALL"
  "2. OS"
  "4. APPS"
  "5. OTA"
  "6. ROM"
  "7. MICOM"
  "8. WIFI"
  "9. LOADPARAM"
  "10. BL1"
  "11. BL2"
  "12. SSSFW"
  "13. WLANFW"
  "14. ERASE OTA"
  "15. ERASE USERFS"
  "16. ERASE ALL"
  "u. USBrule"
  "x. Exit"
==================================================
u

NOTE It requires root permission.

By manually

Make a file named 99-<anyname>.rules.
Add below contents at above file.

SUBSYSTEMS=="usb",ATTRS{idVendor}=="0403",ATTRS{idProduct}=="6010",MODE="0666" RUN+="/sbin/modprobe ftdi_sio" RUN+="/bin/sh -c 'echo 0403 6010 > /sys/bus/usb-serial/drivers/ftdi_sio/new_id'"

Place the above file in /etc/udev/rules.d folder with sudo permission.
Reboot your system.

How to program a binary

After building TizenRT, execute below command at $TIZENRT_BASEDIR/os folder.
See [Getting the sources] for how to set TIZENRT_BASEDIR.

./dbuild.sh download [Programming Option]

For example, ALL option makes complete set of binaries programmed.

./dbuild.sh download ALL

See programming options list which is pre-defined at .flashSpec.xml.

Refer How to program using OpenOCD to make user-specific programming seqeunce.

Factory Reset

If you can not boot normally, you can change os to the initial version. This is possible if there is an initialization binary in memory.

How to Download the Initialization Binaries

You can download it using OpenOCD. You compress the compiled firmware and download it to the board.

gzip -c tinyara_head.bin > factoryimage.gz
openocd -f artik05x.cfg -s ../build/configs/artik05x/scripts -c ' \
    flash_erase_part ota ;\
    flash_write factory    ../build/configs/artik053/bin/factoryimage.gz;      \
    exit'

How to enter initialization mode

When you press the RESET button (SW700) to reboot the Starter Kit, press and hold the 'ARDUINO RESET' button (SW701) for 10 seconds. Enter initialization mode as follows.

.....
Factory reset.
Erasing boot partitions...
....................................e
Erased 600 sectors
Flashing factory image...
Uncompressed size: 1258496 = 0x133400
resetting ...

........ <RESET>.....................
U-Boot 2017
.....

ROMFS

How to set romfs partition

How to use GDB

Run OpenOCD daemon.

@ubuntu:~/TizenRT/os$ ../build/tools/openocd/linux64/openocd -f artik05x.cfg -s ../build/configs/artik05x/scripts/
Open On-Chip Debugger 0.10.0-dirty (2017-09-02-08:32)
Licensed under GNU GPL v2
For bug reports, read
	http://openocd.org/doc/doxygen/bugs.html
adapter speed: 2000 kHz
Info : auto-selecting first available session transport "jtag". To override use 'transport select <transport>'.
force hard breakpoints
trst_and_srst separate srst_gates_jtag trst_push_pull srst_push_pull connect_deassert_srst
adapter_nsrst_assert_width: 50
adapter_nsrst_delay: 100
debug_level: -1

Run GDB at another terminal.
Please find <-- COMMAND at below logs.

@ubuntu:~/TizenRT/os$ arm-none-eabi-gdb ../build/output/bin/tinyara   <-- COMMAND
GNU gdb (GNU Tools for ARM Embedded Processors) 7.8.0.20150604-cvs
Copyright (C) 2014 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>
This is free software: you are free to change and redistribute it.
There is NO WARRANTY, to the extent permitted by law.  Type "show copying"
and "show warranty" for details.
This GDB was configured as "--host=i686-linux-gnu --target=arm-none-eabi".
Type "show configuration" for configuration details.
For bug reporting instructions, please see:
<http://www.gnu.org/software/gdb/bugs/>.
Find the GDB manual and other documentation resources online at:
<http://www.gnu.org/software/gdb/documentation/>.
For help, type "help".
Type "apropos word" to search for commands related to "word"...
Reading symbols from TizenRT/build/output/bin/tinyara...done.
(gdb) target remote:3333   <-- COMMAND
Remote debugging using :3333
0x00003834 in ?? ()
(gdb) monitor reset halt   <-- COMMAND
target halted in ARM state due to debug-request, current mode: Supervisor
cpsr: 0x60000153 pc: 0x040db8a8
D-Cache: enabled, I-Cache: enabled
(gdb) monitor cortex_r4 maskisr on   <-- COMMAND
cortex_a interrupt mask on
(gdb) b hello_main
Breakpoint 1 at 0x40d30fc: file hello_main.c, line 196.
(gdb) b up_assert
Breakpoint 2 at 0x40c9364: file armv7-r/arm_assert.c, line 945.
(gdb) c
Continuing.

Breakpoint 1, hello_main (argc=1, argv=0x202fd1c) at hello_main.c:196
196	{
(gdb) s
197		sleep(20);
(gdb) s
sleep (seconds=seconds@entry=20) at unistd/lib_sleep.c:155
155		if (seconds) {
(gdb) c
Continuing.

Breakpoint 2, up_assert (filename=filename@entry=0x40ea757 "hello_main.c", 
  lineno=lineno@entry=198) at armv7-r/arm_assert.c:945
945		lldbg("Assertion failed at file:%s line: %d task: %s\n", filename, lineno, this_task()->name);
(gdb)

help will help you to find GDB commands.

Configuration Sets

extra

This can be used to use full functionality of TizenRT on ARTIK053.

hello

This provides simple hello world application including kernel.

iotivity

This can be used to use Iotivity (OCF).

iotjs

This can be used to use IoT.js

kernel_sample

This can be used to test kernel functionality.

minimal

This can be used to use the minimal functionality of TizenRT on ARTIK053.

nettest

This can be used to test network functionality.

st_things

This can be used to test Smart Things Things SDK functionality.

tc

This can be used to test database, File System, kernel, network functionality of TizenRT on ARTIK053.

Appendix

On Chip Debugger installation

OpenOCD is used to program and debug.

OpenOCD v0.10.0 is recommended and can be installed like below, but pre-built OpenOCD binaray on tools/openocd/linux64(or 32) can be used without installing.

sudo apt-get build-dep openocd
git clone --depth 1 -b v0.10.0 https://git.code.sf.net/p/openocd/code openocd-code
cd openocd-code
./bootstrap
./configure
make
sudo make install

How to program using OpenOCD

This is used to program a partial binary.
Export 'OPENOCD_SCRIPTS' to environment variable.

export OPENOCD_SCRIPTS=$TIZENRT_BASEDIR/build/tools/openocd

At first, programming the complete set of binaries are needed.

openocd -f artik05x.cfg -s ../build/configs/artik05x/scripts -c ' \
    flash_write bl1    ../build/configs/artik053/bin/bl1.bin;      \
    flash_write bl2    ../build/configs/artik053/bin/bl2.bin;      \
    flash_write sssfw  ../build/configs/artik053/bin/sssfw.bin;    \
    flash_write wlanfw ../build/configs/artik053/bin/wlanfw.bin;   \
    flash_write os     ../build/output/bin/tinyara_head.bin;       \
    exit'

Once the complete binaries are successfully programmed, each partition can be updated separately with new one.

openocd -f artik05x.cfg -s ../build/configs/artik05x/scripts -c ' \
    flash_write os ../build/output/bin/tinyara_head.bin; exit'

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

README.md

README.md

ARTIK 053

Contents

Information

ARTIK053 Starter Kit PinOut

CON710 CON711 CON708 CON709

CON703

CON704

MemoryMap

Environment Set-up

Add USB device Rules

By dbuild.sh script

By manually

How to program a binary

Factory Reset

How to Download the Initialization Binaries

How to enter initialization mode

ROMFS

How to use GDB

Configuration Sets

extra

hello

iotivity

iotjs

kernel_sample

minimal

nettest

st_things

tc

Appendix

On Chip Debugger installation

How to program using OpenOCD

Files

README.md

Latest commit

History

README.md

File metadata and controls

ARTIK 053

Contents

Information

ARTIK053 Starter Kit PinOut

CON710 CON711 CON708 CON709

CON703

CON704

MemoryMap

Environment Set-up

Add USB device Rules

By dbuild.sh script

By manually

How to program a binary

Factory Reset

How to Download the Initialization Binaries

How to enter initialization mode

ROMFS

How to use GDB

Configuration Sets

Appendix

On Chip Debugger installation

How to program using OpenOCD