-
Notifications
You must be signed in to change notification settings - Fork 106
/
8821au.conf
153 lines (153 loc) · 3.74 KB
/
8821au.conf
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
# /etc/modprobe.d/8821au.conf
#
# Purpose: Allow easy access to specific driver options.
#
# Edit the following line to change, add or delete driver options:
#
options 8821au rtw_led_ctrl=1
#
# Note: The above `options` line is a good default for managed mode. Below
# are examples for AP mode. Modify as required after reading the documentation:
#
# Band 1 (2.4 GHz)
#options 8812au rtw_switch_usb_mode=2
#
# Band 2 (5 GHz)
#options 8812au rtw_switch_usb_mode=1 rtw_vht_enable=2 rtw_dfs_region_domain=1 rtw_country_code=US
#
# After editing is complete, save this file (if using nano: Ctrl + x, y, Enter)
# and reboot to activate the changes.
#
# Note: hostapd information is located at the end of this file.
#
# Documentation:
#
# -----
#
# Log options ( rtw_drv_log_level )
#
# 0 = NONE (default)
# 1 = ALWAYS
# 2 = ERROR
# 3 = WARNING
# 4 = INFO
# 5 = DEBUG
# 6 = MAX
#
# Note: You can save a log file that only includes RTW log entries by running
# the following in a terminal:
#
# sudo ./save-log.sh
#
# Note: A log option greater than 1 must be set. The name of the log
# file will be `rtw.log`.
#
# -----
#
# LED options ( rtw_led_ctrl )
#
# 0 = Always off
# 1 = Normal blink (default)
# 2 = Always on
#
# -----
#
# VHT options ( rtw_vht_enable )
#
# 0 = Disable
# 1 = Enable (default)
# 2 = Force auto enable (use only for 5 GHz AP mode)
#
# Notes:
# - A non-default setting can degrade performance greatly in managed mode.
# - Option 2 allows 80 MHz channel width for 5GHz AP mode, such as when
# you are using hostapd.
#
# -----
#
# Power options ( rtw_power_mgnt )
#
# 0 = Disable power saving
# 1 = Power saving on, minPS (default)
# 2 = Power saving on, maxPS (not recommended for AP mode)
#
# -----
#
# DFS Options ( rtw_dfs_region_domain )
#
# 0 = NONE (default)
# 1 = FCC
# 2 = MKK
# 3 = ETSI
#
# Notes:
# - Activates DFS channels in AP mode.
# - DFS FCC 80 MHz channels for hostapd: 52(58), 100(106), 116(122) and 132(138)
# - For more information: https://en.wikipedia.org/wiki/List_of_WLAN_channels
#
# Note: An AP needs to listen on a DFS channel for a period of 60 seconds
# before transmitting on the channel. If any radar pulses are detected,
# the AP cannot use that channel and will have to try a different channel.
#
# -----
#
# Wireless Mode options ( rtw_wireless_mode )
#
# 1 = 2.4GHz 802.11b
# 2 = 2.4GHz 802.11g
# 3 = 2.4GHz 802.11b/g
# 4 = 5GHz 802.11a
# 8 = 2.4Hz 802.11n
# 11 = 2.4GHz 802.11b/g/n
# 16 = 5GHz 802.11n
# 20 = 5GHz 802.11a/n
# 64 = 5GHz 802.11ac
# 84 = 5GHz 802.11a/n/ac
# 95 = 2.4GHz 802.11b/g/n 5GHz 802.11a/n/ac (default)
#
# -----
#
# Country Code options ( rtw_country_code )
#
# Note: Allows the Country Code to be set in cases where it is unable to
# be obtained otherwise.
#
# URL: http://en.wikipedia.org/wiki/ISO_3166-1_alpha-2
#
# Example for the US: rtw_country_code=US
# Example for Panama: rtw_country_code=PA
# Example for Norway: rtw_country_code=NO
# Example for Kuwait: rtw_country_code=KW
# Example for Taiwan: rtw_country_code=TW
#
# -----
#
# To see all driver options that are available:
#
# $ ls /sys/module/8821au/parameters/
#
# -----
#
# To see the values that are in use:
#
# $ grep [[:alnum:]] /sys/module/8821au/parameters/*
#
# -----
#
# hostapd setup information for rtl8821au
# Note: The best settings can vary but the following may be a good place to start.
#
# /etc/modprobe.d/8821au.conf
# options 8821au rtw_drv_log_level=0 rtw_led_ctrl=0 rtw_vht_enable=2 rtw_power_mgnt=1 rtw_dfs_region_domain=1
#
# Note: The best setting for `rtw_dfs_region_domain=` will depend on your location.
#
# /etc/hostapd/hostapd.conf
#
# hw ht capab: 0x962
# ht_capab=[HT40+][HT40-][SHORT-GI-20][SHORT-GI-40][RX-STBC1][MAX-AMSDU-7935]
#
# hw vht capab: 0x3c00122
# vht_capab=[MAX-MPDU-11454][SHORT-GI-80][RX-STBC-1][HTC-VHT][MAX-A-MPDU-LEN-EXP7]
#
# -----