Frankenstein is a quick and dirty firmware, made from different bits and pieces (thus the name) for ESP8266. The features:
- A nice and shiny commandline interface similar to that of u-boot. No more sloppy AT commands.
- Full command line editing and history.
- A very easy way of adding new commands to the shell
- More or less clean code
- Highly configurable (sort of)
- Supports firmware updates over tftp
You can start by grabbing a binary and burning it to your device. Remember about backups, for all your data on the flash will be gone.
Please note, to use proper commandline editing, use a SANE serial terminal emulator.
Linux: minicom, screen, kermit Windows: putty
Do not file bugs telling me that commandline editing doesn't work in, say, coolterm.
If you are communicating with frankenstein with some other hardware, here's some technical stuff for you:
-
All lines you send to ESP8266 should end with CR, i.e. "\r". (No more pressing CTRL^J on Linux terminals, either!)
-
CTRL+C tries to interrupt the running command and unlocks the terminal
-
Install cmake, bash, make (Follow your linux distro manuals. Windows and macOS are untested!)
-
Get ESP Open SDK 2.0 or higher. Grab from here and build in STANDALONE mode xtensa-lx106-elf toolchain should be in your path.
-
Get kconfig-frontends from here and install
Prepare the environment and build it!:
mkdir build
cd build
cmake ..
make menuconfig
make
- Flash the resulting binaries with esptool.py
Now that we're clear with that, let's start the device and open up terminal. You'll see something like this:
Frankenstein ESP8266 Firmware
(c) Andrew 'Necromant' Andrianov 2014 <andrew@ncrmnt.org>
This is free software (where possible), published under the terms of GPLv2
Memory Layout:
data : 0x3ffe8000 ~ 0x3ffe8f60, len: 3936
rodata: 0x3ffe8f60 ~ 0x3ffeae58, len: 7928
bss : 0x3ffeae58 ~ 0x3fff2720, len: 30920
heap : 0x3fff2720 ~ 0x3fffc000, len: 39136
hello=23env: Environment @ 0x0007b000 size 0x00001000 bytes (0x00000ffc real)
env: Bad CRC (fe1 vs ffff) using defaults
Saving environment to flash disabled by config
Recompile with CONFIG_ENV_NOWRITE=n
=== Current environment ===
sta-mode dhcp
default-mode STA
sta-ip 192.168.0.123
sta-mask 255.255.255.0
sta-gw 192.168.0.1
ap-ip 192.168.1.1
ap-mask 255.255.255.0
ap-gw 192.168.1.1
hostname frankenstein
bootdelay 5
dhcps-enable 1
=== 201/4092 bytes used ===
dhcpserver: started
=== Press enter to activate this console ===
frankenstein >
The workflow is simple. You type commands, frankenstein does things. Simple?
You can store come configuration parameters in 'environment'.
Environment is just a key=value storage. Certain variables affect behavior of different commands.
You can list environment with printenv.
=== Current environment ===
sta-mode dhcp
default-mode STA
sta-ip 192.168.0.123
sta-mask 255.255.255.0
sta-gw 192.168.0.1
ap-ip 192.168.1.1
ap-mask 255.255.255.0
ap-gw 192.168.1.1
hostname frankenstein
bootdelay 5
dhcps-enable 1
telnet-port 23
telnet-autostart 1
telnet-drop 60
tftp-server 192.168.1.215
tftp-dir /
tftp-file antares.rom
=== 309/4092 bytes used ===
You can set environment values with setenv.
frankenstein > setenv key value
You can get environment values with getenv. e.g.
frankenstein > getenv key
value
All changes are made in ram. To save them to flash run
saveenv and they will survive reboot.
Environment variables hold paramers for the firmware that are applied on boot or affect certain commands. All variables are described in README.env. You can also store arbitrary data in environment variables.
Wireless modes can be switched using iwmode command.
Modes are: NONE, STA, AP, APSTA.
Default mode is specified in default-mode environment variable.
Use iwmode to switch manually:
frankenstein > iwmode STA
mode change: AP->STA
frankenstein > iwscan
BSSID b0:48:7a:d6:92:a8 channel 11 rssi -88 auth WPA2_PSK TP-LINK_D692A8
BSSID c0:4a:00:c7:9d:8e channel 11 rssi -80 auth WPA_WPA2_PSK Home_TP-LINK
frankenstein > iwconnect apname password
Connected
Spaces are allowed with simple or double quotes:
frankenstein > iwconnect "ap name" 'my password'
iwconnect starts connection process and waits for some seconds until it
either connects or an error occurs. It will continue to try and reconnect in
background.
ifconfig prints the info about curently active interfaces. they are named ap0 and sta0.
They do not correspond (yet!) to lwip iface names.
frankenstein > ifconfig
ap0: WiFi Access Point Interface
state: Running
inet addr:192.168.4.1 Mask:255.255.255.0 Gateway:192.168.4.1
sta0: WiFi Client Interface
state : Connected
rssi : -60
channel : 3
inet addr:192.168.0.198 Mask:255.255.255.0 Gateway:192.168.0.20
apconfig with no arguments shows current ap configuration.
frankenstein > apconfig
SSID: arven AUTH WPA2_PSK BSSID: 1a:fe:34:98:dc:9e
frankenstein > apconfig myap WPA2_PSK 12345678
frankenstein > apconfig
SSID: myap AUTH WPA2_PSK BSSID: 1a:fe:34:98:dc:9e
To enable DHCP server set 'dhcps-enable' to '1' and reboot. To start AP on boot set 'default-mode' to 'AP' or 'APSTA'.
A very simple TCP test command. It will listen on a port and print out the line of text received. '\n' terminates connection.
frankenstein > listen 8080
Listening (TCP) on port 8080
connect | 192.168.0.101:60804
receive | hello
disconnect | 192.168.0.101:60803
A very simple TCP test command. It will connect to a remote host, write a string and disconnect. Disconnect (for some reason) takes a while.
frankenstein > send 192.168.0.101 8080 hello
connected!
data sent
disconnected!
help - Show this message
telnet - start/stop telnet server
telnet start - start service
telnet stop - stop service
telnet quit - drop current client
argtest - Print out argc/argv
deepsleep - Enter deep sleep for some microseconds
deepsleep 10000
reset - Soft-reboot the device
chipinfo - Display chip information
meminfo - Display memory information
hname - Set dhcp hostname
envreset - Reset environment to defaults
resetenv
saveenv - Write environment to flash
setenv var value
getenv - Get an environment variable
getenv var
setenv - Set an environment variable
setenv var value
printenv - Print all environment variables
apconfig - Setup Access Point.
apconfig name OPEN/WEP/WPA_PSK/WPA2_PSK/WPA_WPA2_PSK [password]
iwconnect - Join a network/Display connection status.
iwconnect ssid password
iwmode - Get/set wireless mode. Available modes: NONE, STA, AP, APSTA
iwmode STA
iwscan - Scan for available stations
ifconfig - Show network interfaces and their status
ifconfig [iface]
ifconfig sta0
gpio - Control gpio lines. gpio mode line [value]
gpio in 0
gpio out 0 1
flash_scan - Scan the upper portion of FLASH for dirty blocks
Used to find out where the blobs store config
flash_scan
spi_dump - Hexdump flash contents
spi_dump start len
wipeparams - Wipe blob configuration section of flash
wipeparams any three arguments
spi_wipe - Wipe the whole spi flash blank
wipe any three arguments
listen - Listen for incoming data ona port
listen 8080
send - Send data to a remote host.
send hostname port [data]
ds18b20 - Read temperature from DS18B20 chip.
ds18b20 <gpio>
dht22 - Read temperature and humidity from DHT-11 or DHT-22 module.
dht22 init <gpio> <11|22>
dht22 read
tftp - Update firmware over tftp
tftp
AT - says OK
If you dont have a pl2303 gpio breakoutboard and have to manually set the programming GPIO, use the following procedure.
- Dont be running minicom or other terminal program
- Connect RST and GPIO#0 to GND
- Release RST
- Release GPIO#0 (at least 300ms after)
- Deploy
Frankenstein supports OTA updates via tftp. TFTP update requirements:
- Firmware you're flashing is <=256KiB (SPI_FLASH_SIZE /2 )
- Firmware is made up of ONE file that will be burned at 0x0000
To update use the following:
- Set up a tftp server on the host pc. e.g. tftpd-hpa.
- Set 'tftp-server' environment variable to the tftp server ip address.
- Set 'tftp-dir' and 'tftp-file' to point to your firmware file.
e.g. To get
/tftpboot/antares.romyou'll need
setenv tftp-dir /tftpboot/
setenv tftp-file antares.rom
tftp
Optionally, use saveenv before tftp.
If everything goes well - you'll be running your new firmware in a few seconds.
Note, tftp doesn't check what stuff you have in your image...