Skip to content

Latest commit

 

History

History
153 lines (109 loc) · 6.18 KB

CHANGELOG.md

File metadata and controls

153 lines (109 loc) · 6.18 KB
Raw

Changelog

Version 0.4.9 (14/03/2018)

  • Add: Support for Pi3 Model B+
  • Add: e option to display core voltage

Version 0.4.8 (23/10/2017)

  • Fix: Range errors

Version 0.4.7 (03/10/2017)

  • Add: Support for new models (CM3, Pi0W) and manufacturer (Sony Japan)

Version 0.4.6 (28/08/2017)

  • Fix: Crap...

Version 0.4.5 (28/08/2017)

  • Chg: Ignore invalid network interface and don't output network stats
  • Fix: Support Predictable Network Interface Names in Stretch (ie. enx<MAC> instead of eth0)
  • Add: If not eth0/enx interface, default to wlan0 (should work better with Pi0W)
  • Closes #7

Version 0.4.4 (17/01/2017)

  • Chg: Add additional codecs

Version 0.4.3 (05/10/2016)

  • Fix: Allow for missing CPUFreq interface with kernel 4.8+ when force_turbo=1
  • Chg: Add rounding to measure_clock to account for jitter

Version 0.4.2 (14/08/2016)

  • Fix: Read correct bits when logging past under-voltage/throttle events.

Version 0.4.1 (21/06/2016)

  • Chg: If using recent firmware (>2016-06-20), threshold events that occur during sleep intervals will now be detected and reported
  • Add: If enabled (-y), report peak number of undervolt, frequency cap and throttle events

Version 0.4.0 (13/06/2016)

  • Add: Add y/Y to control display of under-voltage(U)/freq capped(F)/throttle(T) flags

Version 0.3.9 (17/05/2016)

  • Chg: Small bump to support Pi Zero Rev 1.2 and 1.3.

Version 0.3.8 (12/03/2016)

  • Add: Option T to disable 85C temperature limit - useful when stress testing

Version 0.3.7 (29/02/2016)

  • Add: Decode hardware revision
  • Add: Pi3 support

Version 0.3.6 (15/09/2015)

  • Add: Z option to temporarily ignore a default configuration file
  • Add: A option to show accumulated memory deltas (can be used in combination with D)

Version 0.3.5 (14/09/2015)

  • Fix: Cosmetic

Version 0.3.4 (14/09/2015)

  • Chg: Make colourised output the default. Disable with m
  • Chg: Relocate GPU mem columns so that all memory stats are displayed along side each other (when enabled)
  • Chg: Automatically include the GPU (reloc) and ARM memory stats when using option D, if not already enabled by g/x - results in potentially more compact and useful display (eg. Dd10)

Version 0.3.3 (13/09/2015)

  • Fix: Mem delta is in kB not bytes

Version 0.3.2 (13/09/2015)

  • Add: D option to display GPU and ARM memory deltas - memory allocation is shown as negative/red values, while memory freed will be shown as positive/green values. Continuous allocations with no sign of memory being free would suggest memory leakage.

Version 0.3.1 (29/08/2015)

  • Fix: Damn...old firmware.

Version 0.3.0 (29/08/2015)

  • Fix: Bah. Use integer maths and allow a small 50mV variance in the detected sdram voltage

Version 0.2.9 (28/08/2015)

  • Fix: Fix rounding error when sdram voltage is 1.4000V - calculated offset is 7 (from int(7.999999)), when should be 8.

Version 0.2.8 (28/08/2015)

  • Fix: Cosmetic

Version 0.2.7 (28/08/2015)

  • Chg: Update way in which over_volatage_sdram is determined. Now take the maximum measured voltage - sdram_p (pysical), sdram_c (controller) and sdram_i (IO]) - then calculate the sdram over voltage offset that would be required to achieve this voltage. This method does result in a non-overclocked RPi2 showing +1, as over_volatage_sdram_p is slightly overclocked by default.

Version 0.2.6 (13/08/2015)

  • Chg: More tweaks: support disable_auto_turbo

Version 0.2.5 (13/08/2015)

  • Chg: Small tweak to support 300Mhz core/gpu freq dynamic overclock when using "stock" clocks

Version 0.2.4 (26/07/2015)

  • Fix: And use those correct values when colourising output...

Version 0.2.3 (26/07/2015)

  • Fix: More accurately report core/h264 max freq (take gpu_freq into consideration)

Version 0.2.2 (01/05/2015)

  • Fix: Python3 compatibility - closes #3

Version 0.2.1 (19/03/2015)

  • Chg: Cosmetic - correct help description of core optionsp/P

Version 0.2.0 (02/02/2015)

  • Chg: Add W option in place of F to force downloads

Version 0.1.9 (31/01/2015)

  • Add: Show per-CPU load with -p
  • Add: Include CPU type and quantity in summary section
  • Fix: Take multiple CPUs into consideration when calculating system load
  • Chg: Cosmetic, adjust width of Min Freq/Max Freq/Voltages to account for extra decimal on voltage
  • Chg: Cosmetic, reduce spacing between columns to increase data density

Version 0.1.8 (18/07/2014)

  • Chg: Also look for config in ~/.config/bcmstat.conf if not found elsewhere (ie. ~/.bcmstat.conf)

Version 0.1.7 (18/07/2014)

  • Chg: Don't perform auto-update if running from a read-only filesystem

Version 0.1.6 (19/06/2014)

  • Fix: Support hex encoded integers in call to vcgencmd get_config int
  • Fix: When available, use vcgencmd get_mem [reloc_total|reloc|malloc_total|malloc] calls rather than vcdbg reloc which suffers from cache coherency issues
  • Add: New f option to display malloc gpu memory (g already shows reloc memory). Contrary option is F to disable malloc display.
  • Chg: Invert interpretation of the s and S (swap memory) options, these seem to have been interpreted the wrong way around...

Version 0.1.5 (06/04/2014)

  • Fix: Store tmCore/TMAX as float not int to avoid loss of precision - thanks g7ruh. Closes #1

Version 0.1.4 (14/02/2014)

  • Add: Display peak IRQ, RX and TX values when terminating bcmstat.sh with ctrl-c

Version 0.1.3 (13/02/2014)

  • Chg: Use vcgencmd get_mem gpu and vcgencmd get_mem arm to calculate GPU/ARM split, and total available RAM.

Version 0.1.2 (09/02/2014)

  • Detect XBian

Version 0.1.1 (26/01/2014)

  • Add: Include "SwUse" (Swap Used %) in memory statistics if swap memory is enabled

Version 0.1.0 (25/01/2014)

  • Add: Include Swap allocation (if swap is enabled) in summary information

Version 0.0.9 (23/01/2014)

  • Fix: Show correct Core/SDRAM frequency when not overclocked (or when underclocked)
  • Add: Min/Max H264 frequency

Version 0.0.8 (21/01/2014)

  • Chg: Small change to filter on interface data, making it less likely to be ambiguous
  • Chg: Improve interface name validation

Version 0.0.7 (06/01/2014)

  • Chg: Tweak Raspbmc/Raspbian identification

Version 0.0.6 (05/01/2014)

  • Initial github release
  • Add: Add self-update options (V, U, F, C)