Skip to content

bgp_multipath_wecmp_lbw_community_test

Jump to bottom
Github Action edited this page Oct 23, 2024 · 4 revisions

RT-1.52: BGP multipath UCMP support with Link Bandwidth Community

Summary

Validate BGP in multipath UCMP support with link bandwidth community

Testbed type

TESTBED_DUT_ATE_4LINKS

Procedure

Setup

  • Connect DUT port 1, 2 and 3 to ATE port 1, 2 and 3 respectively
  • Configure IPv4/IPv6 addresses on the interfaces
  • Establish eBGP sessions between:
    • ATE port-1 and DUT port-1
    • ATE port-2 and DUT port-2
    • ATE port-3 and DUT port-3
  • Enable an Accept-route all import-policy/export-policy for eBGP session under the neighbor AFI/SAFI - IPv6 unicast and IPv4 unicast.
  • Create an single IPv4 internal target network attached to ATE port 2 and 3
  • Create an single IPv6 internal target network attached to ATE port 2 and 3

Tests

  • RT-1.52.1: Verify use of unequal community type

    • Test Configuration
      • Configure ATE port 1, 2 and 3 on different AS, with boths AFI/SAFI
        • Advertise IPv4 and IPv6 internal target, both, form both ATE port-1 and ATE port-2 in eBGP.
        • For ATE port 2 attach link-bandwidth:23456:10K extended-community
        • For ATE port 3 attach link-bandwidth:23456:5K extended-community
      • Enable multipath, set maximum-paths limit to 2, enable allow multiple AS, and send community type to [STANDARD, EXTENDED, LARGE]
        • /network-instances/network-instance/protocols/protocol/bgp/peer-groups/peer-group/afi-safis/afi-safi/use-multiple-paths/config/enabled
        • /network-instances/network-instance/protocols/protocol/bgp/global/afi-safis/afi-safi/use-multiple-paths/ebgp/config/allow-multiple-as
        • /network-instances/network-instance/protocols/protocol/bgp/global/afi-safis/afi-safi/use-multiple-paths/ebgp/config/maximum-paths
        • /network-instances/network-instance/protocols/protocol/bgp/peer-groups/peer-group/config/send-community-type
        • /network-instances/network-instance/protocols/protocol/bgp/global/use-multiple-paths/ebgp/link-bandwidth-ext-community/config/enabled
      • Advertise equal cost paths from port2 and port3 of ATE
      • Initiate traffic from ATE port-1 to the DUT and destined to internal target network.
        • Use UDP traffic with src and dst port randomly selected from 1-65535 range for each packet. Or equivalent pattern guaranteeng high entropy of traffic.
    • Behaviour Validation
      • Check entries in AFT for advertised prefix, it should have 2 entries.
        The weight leafs of next-hops shall be in 2:1 ratio.
        • Find next-hop-group IDs for both internal target networks:
          • /network-instances/network-instance/afts/ipv4-unicast/ipv4-entry[prefix=IPv4 internal target network]/state/next-hop-group
          • /network-instances/network-instance/afts/ipv4-unicast/ipv4-entry[prefix=IPv6 internal target network]/state/next-hop-group
        • using next-hop-group as key find number and weight of next-hops of both internal target network
          • /network-instances/network-instance/afts/next-hop-groups/next-hop-group[id=next-hop-group ID]/next-hops/next-hop/state/index
          • /network-instances/network-instance/afts/next-hop-groups/next-hop-group[id=next-hop-group ID]/next-hops/next-hop/state/weight
      • Check entire traffic should be unequally forwarded between DUT port2 and port3 only * 66% via port2 * 33% via port3 * with +/-5% tolerance

  • RT-1.52.2: Verify use of equal community type

    • Test Configuration Use test configuration as in RT-1.52.1 above with following modifications:
      • Advertise IPv4 and IPv6 internal target, both, form both ATE port-1 and ATE port-2 in eBGP. * For ATE port 2 attach link-bandwidth:23456:10K extended-community * For ATE port 3 attach link-bandwidth:23456:10K extended-community
    • Behaviour Validation
      • Check entries in AFT for advertised prefix, it should have 2 entries.
        The weight leafs of next-hops shall be in 1:1 ratio.
        • Find next-hop-group IDs for both internal target networks:
          • /network-instances/network-instance/afts/ipv4-unicast/ipv4-entry[prefix=IPv4 internal target network]/state/next-hop-group
          • /network-instances/network-instance/afts/ipv4-unicast/ipv4-entry[prefix=IPv6 internal target network]/state/next-hop-group
        • using next-hop-group as key find number and weight of next-hops of both internal target network
          • /network-instances/network-instance/afts/next-hop-groups/next-hop-group[id=next-hop-group ID]/next-hops/next-hop/state/index
          • /network-instances/network-instance/afts/next-hop-groups/next-hop-group[id=next-hop-group ID]/next-hops/next-hop/state/weight
      • Check entire traffic should be unequally forwarded between DUT port2 and port3 only
        • 50% via port2
        • 50% via port3
        • with +/-5% tolerance

  • RT-1.52.3: Verify BGP multipath when some path missing link-bandwidth extended-community

    • Test Configuration Use test configuration as in RT-1.52.1 above with following modifications:
      • Configure ATE port 1, 2 and 3 on different AS, with boths AFI/SAFI
        • Advertise IPv4 and IPv6 internal target, both, form both ATE port-1 and ATE port-2 in eBGP.
        • For ATE port 2 attach link-bandwidth:23456:10K extended-community
        • For ATE port 3 DO NOT attach any link-bandwidth extended-community
    • Behaviour Validation
      • Check entries in AFT for advertised prefix, it should have 2 entries.
        The weight leafs of next-hops shall be in 1:1 ratio.
        • Find next-hop-group IDs for both internal target networks:
          • /network-instances/network-instance/afts/ipv4-unicast/ipv4-entry[prefix=IPv4 internal target network]/state/next-hop-group
          • /network-instances/network-instance/afts/ipv4-unicast/ipv4-entry[prefix=IPv6 internal target network]/state/next-hop-group
        • using next-hop-group as key find number and weight of next-hops of both internal target network
          • /network-instances/network-instance/afts/next-hop-groups/next-hop-group[id=next-hop-group ID]/next-hops/next-hop/state/index
          • /network-instances/network-instance/afts/next-hop-groups/next-hop-group[id=next-hop-group ID]/next-hops/next-hop/state/weight
      • Check entire traffic should be unequally forwarded between DUT port2 and port3 only
        • 50% via port2
        • 50% via port3
        • with +/-5% tolerance

OpenConfig Path and RPC Coverage

rpcs:
  gnmi:
    gNMI.Get:
    gNMI.Subscribe:
paths:
  ## Config Parameter Coverage
  /network-instances/network-instance/protocols/protocol/bgp/peer-groups/peer-group/afi-safis/afi-safi/use-multiple-paths/config/enabled:
  /network-instances/network-instance/protocols/protocol/bgp/global/afi-safis/afi-safi/use-multiple-paths/ebgp/config/allow-multiple-as:
  /network-instances/network-instance/protocols/protocol/bgp/global/afi-safis/afi-safi/use-multiple-paths/ebgp/config/maximum-paths:
  /network-instances/network-instance/protocols/protocol/bgp/peer-groups/peer-group/config/send-community-type:
  /network-instances/network-instance/protocols/protocol/bgp/global/use-multiple-paths/ebgp/link-bandwidth-ext-community/config/enabled:

  ## Telemetry Parameter Coverage
  /network-instances/network-instance/afts/ipv4-unicast/ipv4-entry/state/next-hop-group:
  /network-instances/network-instance/afts/next-hop-groups/next-hop-group/next-hops/next-hop/state/weight:

Required DUT platform

  • FFF - Fixed Form Factor
Clone this wiki locally