Merge pull request #13 from AtaBayraktar0/main

KNK Force and 2 Images

docs/Technologies/KNKForce.md

@@ -9,76 +9,93 @@ permalink: /docs/technologies/KNKForce
 # HOW TO USE KNK FORCE
 
  ## Setup:
-  
+
  ### Materials:
-
-  * KNK Force
-  * Charging Cable (has a sticker on it that says “KNK”)
-  * WIFI Adapter or Ethernet cable 
-  * Cutter blade
-  * Cutting Mat
-  * Pen ( necessary for print and cut only )
+   - KNK Force
+   - Charging Cable (has a sticker on it that says “KNK”)
+   - WIFI Adapter or Ethernet cable 
+   - Cutter blade
+   - Cutting Mat
+   - Pen (necessary for print and cut only)
 
  ### For WIFI Connection:
-  Plug the device in and plug the WIFI adapter into it
+ Plug the device in and plug the WIFI adapter into it.
 
  ### For Ethernet Connection:
-  Plug the ethernet and charging cable only
+ Plug the ethernet and charging cable only.
 
  ## Connection:
-
- * Press the start button
- * A blue light will blink (might take up to 1-2 minutes)
- * Another light will appear after the blinking
-   -If it is Red: KNK doesn’t receive a connectable WIFI signal (WIFI adapter is required)
-   -If it is Green: KNK is in recovery mode and needs a manual reset. See the instructions below
-   -If it is White KNK is ready for the next step
- * Open WIFI settings from your PC and choose KNK_Force network
- * KNK is now connected to the PC 
-
-  Problems with connection? Check [Article 2.02.2](https://www.iloveknk.com/0um/Force-with-C3/KNKForce-with-C3-UM.pdf) in the PDF
-
- ### Software:
-
- * Sure Cuts a Lot (SCAL) is a software that includes KNK Force machine support. See the download link [here](https://www.craftedge.com/download/downloads.php)
- * Softwares like Inkscape are also usable with KNK Force. However, most of them require an extension to connect the device.
-
- ### SCAL First Cut:
-
- * [This Video](https://www.youtube.com/watch?v=ZcJj5l7TY34) might help for the first cut to learn about the software.
- * You’ll need an IP Address to start cutting. (The KNK with Print and Cut sticker has 10.0.0.1 as an IP)
- * IP address can be obtained by:
-    -plug an Ethernet into the machine and the PC
-    -Run Command Prompt on PC
-    -Type ipconfig and see the results of the Ethernet Cable.
-    Or
-    -Connect KNK to WIFI
-    -Connect to the KNK via WIFI
-    -Download Angry IP and search for the device
+   1. Press the start button.
+   2. A blue light will blink (might take up to 1-2 minutes).
+   3. Another light will appear after the blinking:
+      - If it is Red: KNK doesn’t receive a connectable WIFI signal (WIFI adapter is required).
+      - If it is Green: KNK is in recovery mode and needs a manual reset. See the instructions below.
+      - If it is White: KNK is ready for the next step.
+   4. Open WIFI settings from your PC and choose KNK_Force network.
+   5. KNK is now connected to the PC.
+
+ ### Problems with the connection?
+ Check [Article 2.02.2](https://www.iloveknk.com/0um/Force-with-C3/KNKForce-with-C3-UM.pdf) in the PDF.
+
+ ## Software:
+   - Inkscape is compatible with the device.
+   - IP address includes a software with it for cutting.
+
+ ## First Cut:
+   - You’ll need an IP Address to start cutting. (The KNK with “Print and Cut sticker” has 10.0.0.1 as an IP).
+   - IP address can be obtained by:
+   - Plug an Ethernet into the machine and the PC.
+   - Run Command Prompt on PC.
+   - Type ipconfig and see the results of the Ethernet Cable.
+   - Or
+   - Connect KNK to WIFI.
+   - Connect to the KNK via WIFI.
+   - Download Angry IP and search for the device.
+ ## Cutting:
+   - After you get the IP, type it into your search engine.
+   - An Interface for KNK will show up.
+   - Prepare a design from Inkscape for cutting.
+       ![A square design](SquareKNK.png)
+   - After designing in Inkscape, follow File>Save As…>[Name of your file] and select .svg.
+       ![Saving](FileSaveKNK.png)
+   - Open up the browser again and select "Upload a new SVG pattern:" 
+   - Select your design and wait for the upload. Then return to the main page.
+   - Set up your tool (see instructions below)
+   - Place your mat and material (Check [Article 1.10](https://www.iloveknk.com/0um/Force-with-C3/KNKForce-with-C3-UM.pdf) for the mat details)
+   - Select “Prepare this cutting job”
+   - Adjust the starting position of your KNK using arrows and numpad (Depends on the mat and material size) 
+
+
+ ## Setting up the Cutter/Pen tool:
+   - Setup for the tool is needed after EVERY TIME you turn KNK on.
+   - In the browser UI, select the replace left tool (ALWAYS use the left slot for single tool)
+   - Take every tool out if they were left there in the previous session and click continue
+   - Put the tool back in and adjust the screws. 
+   - The tool is set up! For pen or blade tension and adjustments, make sure you read [Article 1.08](https://www.iloveknk.com/0um/Force-with-C3/KNKForce-with-C3-UM.pdf) in the PDF.
 
  ## Recovery Mode:
 
    ### Getting the device into recovery mode:
 
- * Unplug the WIFI adapter and plug the ethernet cable
- * Turn on the KNK and wait for the red light (might take 1-2 minutes)
- * Take the ethernet cable out and back in. Also, plug the WIFI adapter this time
- * Wait for the lights to turn green
- * Now the device is in recovery mode
+   * Unplug the WIFI adapter and plug the ethernet cable
+   * Turn on the KNK and wait for the red light (might take 1-2 minutes)
+   * Take the ethernet cable out and back in. Also, plug the WIFI adapter this time
+   * Wait for the lights to turn green
+   * Now the device is in recovery mode
 
-   ### Setting up a KNK with recovery mode:
+  ### Setting up a KNK with recovery mode:
 
- *	Select the KNK_Force_Recovery network from WIFI connections. A page will open up on the screen
- * Select LAN if you want to continue the connection with ethernet
- * Save the changes and click continue
- * An IP address will open up.
- * Connect to your regular WIFI network and refresh your KNK connection from SCAL
- * It is connected and you are all set!
+   * Select the KNK_Force_Recovery network from WIFI connections. A page will open up on the screen
+   * Select LAN if you want to continue the connection with ethernet
+   * Save the changes and click continue
+   * An IP address will open up.
+   * Connect to your regular WIFI network and refresh your KNK connection
+   * It is connected and you are all set!
 
  ## For further questions,
- * Check the [C3 User Manual (recommended)](https://www.iloveknk.com/0um/Force-with-C3/KNKForce-with-C3-UM.pdf) or [SCAL 5 User Manual](https://www.iloveknk.com/0um/Force-with-SCAL5/KNKForce-with-SCAL5-UM.pdf).
- Or 
- * [KNK Manuals Page](https://www.iloveknk.com/support/knk-force-support-page/) for video support & more
+   * Check the [C3 User Manual (recommended)](https://www.iloveknk.com/0um/Force-with-C3/KNKForce-with-C3-UM.pdf) or [SCAL 5 User Manual](https://www.iloveknk.com/0um/Force-with-SCAL5/KNKForce-with-SCAL5-UM.pdf).
+   Or 
+   * [KNK Manuals Page](https://www.iloveknk.com/support/knk-force-support-page/) for video support & more