Skip to content

ForzaShiftTone v0.6
Compare
Choose a tag to compare
@theRTB theRTB released this 13 Sep 13:55
· 139 commits to main since this release
v0.6
d885ff9
This commit was created on GitHub.com and signed with GitHub’s verified signature. The key has expired.
GPG key ID: 4AEE18F83AFDEB23
Expired
Learn about vigilant mode.

ForzaShiftTone

Windows GUI application to provide a shift tone in Forza Horizon 5.

example v0.4 BMW M5 2018

Enable remote telemetry / Data out

To enable remote telemetry in Forza Horizon 5 on Steam for this application:

  • Head to Settings -> HUD and Gameplay -> scroll down to the bottom
  • Set Data Out to On, enter 127.0.0.1 as Data out IP address and Data out IP port 12350. You may have to restart the game.
    • XBox Data Out is to my knowledge broken, but would otherwise require the Data Out IP Address to be your laptop's IP address instead and the address modified in config.json. This is untested.
    • For the Microsoft Store version, install the Loopback Utility found on the internet.

Current release

If you are unsure which file to pick, download the ForzaShiftTone.v0.6.zip file.
The ForzaShiftTone.v0.6_debug.zip file will open a commandline prompt with extra debug information alongside the GUI.

Changes:

  • Double beep on locking gear ratio per gear
  • Triple beep if the power curve has been succesfully collected the first time
  • Adjustments to filtering for boost to fix some cars never passing the various checks for the power curve
  • Revlimit turns green if a power curve has been collected
  • Various settings have been softcoded into config.json
  • First attempt to fix scaling according to Windows DPI scaling

Considerations

While it is intended to run in the background without consideration while driving, there are some requirements to having accurate shift tones:

  • Drive for over one second in a single gear on road. After this the gear values will lock and turn green. There will be a short double beep.
    • Road surfaces are far more accurate than dirt/off-road
    • For AWD cars: maintain throttle at a fixed amount at speed
  • Starting from a low to medium RPM accelerate at full throttle all the way to rev limit. Rev limit should normally be avoided, but must be hit once for accurate data. Avoid impacts and ignore the shift beep. There will be a short triple beep if succesful.
    • At minimum the power at the start must be equal or lower than power at revlimit. For most cars this is easy to achieve by starting at around halfway redline
    • Boost is taken into account. Some cars with very high boost may require a run at relatively low rpm in a relatively high gear to ensure enough data points at peak boost
  • a more accurate rev limit is derived from the required run. Defaults to maximum engine rpm minus 750

Browser/Windows warnings

The current release is a Pyinstaller package that is not signed. This means various browsers and Smartscreen inside Windows are going to complain the file is unsafe or an uncommon download. Future releases will remain unsigned as it is not worthwhile.

Implementation

The Tone Offset is dynamic. The program keeps track of the time between a shift tone and an initiated shift, and modifies the running Tone Offset if the tone is early or late.
There are three triggers:

  • Shift RPM: The RPM value at which power in the current becomes lower than the power in the next gear: the ideal time to upshift. If the application predicts shift RPM is reached in the defined tone offset time, trigger a beep
  • Percentage of revlimit: Uses the tone offset distance as predicted distance to current RPM hitting the listed percentage of rev limit
    • Example: A rev limit of 7850 and a value of 99.6% triggers a beep if it predicts 7818.6 rpm will be reached in 283 milliseconds
  • Time distance to revlimit: uses the tone offset value plus the revlimit ms value as predicted distance to current RPM hitting the defined revlimit. Defaults to 83 milliseconds, which leads to a prediction distance of 367ms.

The delay between beep triggers is currently set to 0.5 seconds. This time-out is shared between the three triggers.
If you choose to not shift and remain above the trigger rpm, the program will not beep again even if revlimit is hit.

Settings

The settings are saved to config.json on exit. This includes Revlimit %, Revlimit ms, Tone offset, Hysteresis, and Volume.
Remote telemetry sends data at 60 packets per second. The offset variables (Tone offset, revlimit ms) while defined in milliseconds currently use packet counts in the backend.
There is one packet per 16.667 milliseconds, approximately.

Per gear:

  • RPM: Derived shift rpm value. This requires the ratio of the current gear and the next gear to be determined (green background)
  • Ratio: Derived gear ratio including final ratio. Final ratio cannot be separately derived and for AWD the ratio is not identical to the in-game gearing values.

General configuration:

  • Revlimit: The limit on engine RPM by its own power. Initial guess is maximum engine rpm minus 750. Revlimit is derived upon finishing a full throttle sweep up to revlimit.
  • Tone offset: Predicted distance between the beep trigger and the trigger rpm value. This should not be taken as reaction time and minimized. It should be regarded as the time you can consistently respond to the tone with the least amount of mental effort. Defaults to 283 ms.
  • Revlimit %: The respected rev limit in percentage of actual rev limit. This is to create a buffer for transients that could cause the engine to cut out due to hitting actual rev limit. Defaults to 99.6%.
  • Revlimit ms: The minimum predicted distance to actual rev limit. This is to create a buffer for fast changes in RPM that would otherwise lead to hitting actual rev limit, such as in first gear. Defaults to 83ms.
  • Hysteresis: Hysteresis may be set as another layer to smooth rpm. An intermediary rpm value is updated only if the change in rpm is larger than the hysteresis value, which is then used for the shift beep tests. Defaults to 1 rpm currently.
  • Volume: Adjusts the volume of the beep in four steps total. Each step is about half as loud as the previous, where the loudest is the default.
  • Active tickbox: If unticked, application will not track incoming packets and therefore not beep or update.
  • Edit tickbox: If unticked, the up and down arrows for the Tone offset, Revlimit ms/% and Hysteresis values do not function. This is to avoid accidental clicks.
  • Reset button: If pressed, reset revlimit and all values for all gears. Configuration values are unchanged. If the UI is unresponsive, restart the application.
Assets 4
Loading