This repository contains a set of demo applications for the wolfSSL embedded SSL/TLS library using the Microchip ATECC608A module. wolfSSL is a lightweight, embedded SSL/TLS library that supports up to the most current TLS 1.3 and DTLS 1.2 protocols. These demos use the Microchip ATECC608A Trust&GO module configuration by default, but could be easily adapted to be run with either TrustFLEX or TrustCUSTOM modules.
This repository is intended for demo/example purposes only. It includes driver and middleware code which is copyright of Microchip Technology Inc.
- wolfMQTT TLS Client: wolfmqtt_trust_platform
- wolfSSL TLS Client: wolfssl_client_trust_platform
The included demo applications have been created for the following development environment and hardware platform:
IDE: MPLABX v5.35
Compiler: Microchip XC32 v2.30 compiler
Harmony: Microchip Harmony 3
cryptoauthlib: v3.1.0
wolfSSL: modified version of 4.3.0
PIC32MZEF Curiosity 2.0 board (DM320209)
LAN8720A PHY Daughter Board (AC320004-3)
ATECC608A Trust (DT100104) - using TNGTLS (Trust&GO) module
This repository contains the following demo applications. These applications have been set up to use the pre-configured Microchip Trust&GO ATECC608A module.
Located in the "wolfcrypt_test" directory, this application runs the wolfCrypt cryptography tests and verifies all algorithms are working correctly on the target platform. See the README.md located in the "wolfcrypt_test" directory for more details.
Located in the "wolfssl_client" directory, this application makes a simple TLS 1.2 client connection, sends an HTTP GET message, and prints the server response that is received. See the README.md located in the "wolfssl_client" directory for more details.
Located in the "wolfssl_server" directory, this application runs a simple single-threaded TLS 1.2 server application. This server waits for a client connection, establishes a secure TLS 1.2 connection, reads a message from the client, then sends back a simple HTTP web page in response. See the README.md located in the "wolfssl_server" directory for more details.
wolfSSL has several build options for customizing the integration of the library with ATECC508/608A modules. Further documentation can be found in the README.md located in the wolfSSL library, at:
/wolfcrypt/src/port/atmel/README.md
WOLFSSL_ATECC508A - Enable support for ATECC508A modules.
WOLFSSL_ATECC608A - Enable support for ATECC608A modules using the
Microchip cryptoauthlib library. By default uses wolfSSL's default ATECC slot
configuration settings. ATECC608A slot usage settings can be customized by
implementing a custom slot allocator function (see below), or by enabling
wolfSSL support for pre-configured ATECC608A module such as Trust&GO.
WOLFSSL_ATECC_TNGTLS - Used in addition to WOLFSSL_ATECC608A to enable
out-of-the-box support and slot configuration for Microchip Trust&GO modules.
WOLFSSL_ATECC_PKCB - Enables support for the reference public key (PK)
callbacks without requiring applications to manually initialize them.
WOLFSSL_ATECC_RNG - Enable support for using ATECC RNG.
WOLFSSL_ATECC_SHA256 - Enable support for using ATECC SHA-256.
WOLFSSL_ATECC_ECDH_ENC - Enable use of atcab_ecdh_enc() for encrypted ECDH
operations. Note that this requires special slot configuration, and in most
cases WOLFSSL_ATECC_ECDH_IOENC should be used instead.
WOLFSSL_ATECC_ECDH_IOENC - Enable use of atcab_ecdh_ioenc() for encrypted
ECDH operations using the ATECC I/O protection key for encryption.
WOLFSSL_ATECC_DEBUG - Enable wolfSSL ATECC debug messages.
ATECC_GET_ENC_KEY - Macro to define your own function for getting the I/O
encryption key. See examples for sample usage.
wolfSSL fully supports integration with the pre-configured and provisioned Trust&GO TLS modules. When using wolfSSL with Trust&GO modules, both WOLFSSL_ATECC608A and WOLFSSL_ATECC_TNGTLS should be defined when compiling the library sources. Other defines can be added as needed/required.
The ATECC608A-TNGTLS datasheet can be found on the Microchip website for full module details.
wolfSSL uses the following slot configuration with Trust&GO modules:
- Slot 0 - Device ECC private key, used for ECDSA sign/verify operations
- Slot 2 - ECDH key slot, used for ECDH shared secret generation
- Slot 6 - I/O protection key slot, used to encrypt ECDH shared secret
The examples in this repository use the following ATECC configuration with to initialize cryptoauthlib and the ATECC608A I2C module:
/* configuration for ATECC608A Trust&GO module */
ATCAIfaceCfg atecc608a_0_init_data_TNGTLS = {
.iface_type = ATCA_I2C_IFACE,
.devtype = ATECC608A,
.atcai2c.slave_address = 0x6A,
.atcai2c.bus = 0,
.atcai2c.baud = 400000,
.wake_delay = 1500,
.rx_retries = 20,
.cfg_data = &i2c1_plib_api
};
Although these demo applications are set up to use the Microchip Trust&GO modules by default, they should be easily adaptable to the TrustFLEX modules. TrustFLEX uses the same slot configuration as Trust&GO, with the main difference being that custom certificates are used and provisioned to the module instead of the default Microchip certificates used with Trust&GO. On the ATECC608A development kits, TrustFLEX modules use a different I2C address than Trust&GO (0xC6). To connect to these modules, a cryptoauthlib configuration would need to be used similar to below:
/* configuration for ATECC608A TrustFLEX module */
ATCAIfaceCfg atecc608a_0_init_data_TrustFLEX = {
.iface_type = ATCA_I2C_IFACE,
.devtype = ATECC608A,
.atcai2c.slave_address = 0xC6,
.atcai2c.bus = 0,
.atcai2c.baud = 400000,
.wake_delay = 1500,
.rx_retries = 20,
.cfg_data = &i2c1_plib_api
};
If using these demo applications with a TrustFLEX module, areas of code that use the cryptoauthlib TNG APIs will need to be converted to loading the correct device and signer certificates. For example, in the "wolfssl_client" and "wolfssl_server" applications, functionality in "common/tls_common.c" will need to be adjusted. There are reference functions commented out which can act as a starting point: tls_build_signer_ca_cert() and tls_build_end_user_cert(), which would replace the Trust&GO specific functions: tls_build_signer_ca_cert_tlstng() and tls_build_end_user_cert_tlstng().
wolfSSL is compatible with Microchip TrustCUSTOM modules through the ability for users to write and register their own ATECC608A slot allocator function with wolfSSL. This will allow wolfSSL to use a custom slot definition for ECDSA and ECDH operations. On ATECC608A development kits, the Microchip TrustCUSTOM modules use a different I2C address than Trust&GO or TrustFLEX. The default I2C address for TrustCUSTOM is 0xC0. To connect to these modules, a cryptoauthlib configuration would need to be used similar to below:
/* configuration for ATECC608A TrustCUSTOM module */
ATCAIfaceCfg atecc608a_0_init_data_TrustCUSTOM = {
.iface_type = ATCA_I2C_IFACE,
.devtype = ATECC608A,
.atcai2c.slave_address = 0xC0,
.atcai2c.bus = 0,
.atcai2c.baud = 400000,
.wake_delay = 1500,
.rx_retries = 20,
.cfg_data = &i2c1_plib_api
};
wolfSSL integrates with ATECC608A modules and cryptoauthlib primarily in the following two source files (header and source):
<wolfssl>/wolfssl/wolfcrypt/port/atmel/atmel.h
<wolfssl>/wolfcrypt/src/port/atmel/atmel.c
wolfSSL uses a default slot allocation scheme for ATECC508A or ATECC608A Trust&GO modules. This default slot allocator can be found in atmel.c, and is called atmel_ecc_alloc(). There is also a default slot free function called atmel_ecc_free(). The default slot allocator is set up to allow individual slots to be changed in the existing allocator structure using the following preprocessor defines:
ATECC_MAX_SLOT - Sets the maximum usable slot number
ATECC_SLOT_AUTH_PRIV - Device key, used for ECDSA sign/verify
ATECC_SLOT_ECDHE_PRIV - Ephemeral ECDH key slot
ATECC_SLOT_I2C_ENC - Symmetric I/O protection key
ATECC_SLOT_ENC_PARENT - Key used to encrypt ECDH shared secrets
By default, the wolfSSL Trust&GO configuration (WOLFSSL_ATECC_TNGTLS) uses the following slots:
#define ATECC_MAX_SLOT (0x8) /* only use slots 0-7 */
#define ATECC_SLOT_AUTH_PRIV (0x0) /* device private key */
#define ATECC_SLOT_ECDHE_PRIV (0x2) /* ECDHE key slot */
#define ATECC_SLOT_I2C_ENC (0x06) /* I/O protection key */
#define ATECC_SLOT_ENC_PARENT (0x6) /* ECDH encryption key */
If the above defines do not allow for enough customization, users can write a custom slot allocator function to return slot numbers to wolfSSL when a specific type of operation is requested. A custom slot allocator and free function can be registered by using the following function:
#include <wolfssl/wolfcrypt/port/atmel/atmel.h>
typedef int (*atmel_slot_alloc_cb)(int slotType);
typedef void (*atmel_slot_dealloc_cb)(int slotId);
int atmel_set_slot_allocator(atmel_slot_alloc_cb alloc,
atmel_slot_dealloc_cb dealloc);
Custom allocator functions should accept a slotType, which will be requested by wolfSSL when required by internal ECDSA/ECDH functionality. Possible slot types are listed in the "atmelSlotType" enum in atmel.h:
enum atmelSlotType {
ATMEL_SLOT_ANY,
ATMEL_SLOT_ENCKEY,
ATMEL_SLOT_DEVICE,
ATMEL_SLOT_ECDHE,
ATMEL_SLOT_ECDHE_ENC,
};
Before wolfSSL can use and interact with ATECC608A modules over I2C, applications should provide wolfSSL with the correct ATCAIfaceCfg definition through the following function:
#include <wolfssl/wolfcrypt/port/atmel/atmel.h>
int wolfCrypt_ATECC_SetConfig(ATCAIfaceCfg* cfg);
Several ATECC608A operations can encrypt the data being transferred via I2C using the I/O protection key. This key is commonly set up during an initial pairing between the ATECC608A module an MCU, so that they both share the same key and can use it to encrypt/decrypt data travelling over the I2C bus.
By default, wolfSSL uses a I/O protection key of all zero's. Applications should provide wolfSSL with the ability to obtain the actual I/O protection key. They can do this by defining the following macro to a function that copies the protection key into the 'enckey' argument array:
#define ATECC_GET_ENC_KEY(enckey, keysize) atmel_get_enc_key_default((enckey), (keysize))
For support inquiries and questions, please email support@wolfssl.com.